Cut Sheet

www.panduit.com/networkzone
specifications
The pre-configured network zone system shall be validated to accommodate
one or two industrial switches with optional expansion modules, and power
supply for use in an EtherNet/IP* zone architecture/topology. The enclosure
shall be UL Type 4/12/4X and IP66 rated. A removable pre-engineered back
plate with DIN rails installed shall be incorporated in the enclosure to enable
rapid installation of switch, power supply and uninterruptible power supply
(UPS). Pre-installed accessory side panels, fiber slack spool, and L rings shall
be included for cable management. The door shall be secured with 3mm
double bit or slotted latch drive feature. The door shall hinge on the right or
left. Class 2 power circuits shall be pre-wired, labeled, and tested. A barrier
shall be present to isolate IT personnel from high voltage power circuit.
Pre-Configured Network Zone System
SPECIFICATION SHEET
applications
The Panduit Pre-Configured Network Zone System
protects industrial switches using a building block
approach, helping to easily define a plant-wide
Ethernet architecture. The system is designed to
rapidly deploy the network by minimizing
engineering and installation time. With UL Type
4/12/4X and IP 66 ratings, the enclosures provide
reliability and high performance, as an integral
component of the end-to-end solution for Industrial
Networks.
*EtherNet/IP is a trademark of ODVA.
technical information
Standards:
UL 508A Standard for Industrial Control Panels, UL Type 4/12 or 4X, IP66 Rated
Dimensions:
Z23C with mounting angles: 40.0"H x 24.0"W x 11.7"D (1016mm x 610mm x 297mm)
Without mounting angles: 36.0"H x 24.0" W x 11.7"D (914mm x 610mm x 297 mm)
Z22C with mounting angles: 28.0"H x 24.0" W x 11.7"D (711mm x 610mm x 297mm)
Without mounting angles: 24.0"H x 24.0" W x 11.7"D (610mm x 610mm x 297 mm)
Z11C with mounting angles: 18.0"H x 12.0" W x 9.7"D (457mm x 305mm x 247mm)
Color and
material:
Enclosures: Gray, 14 gauge cold roll steel or 316 stainless steel
Back panels: 14 gauge galvannealed steel or 304 stainless steel
Thermal
analysis:
Validated to 140°F/60°C
Mounting:
Wall mount with optional outside-mount flange
key features and benefits
Pre-configured solution
Reduces time required for planning, designing, procurement, and installation,
resulting in simpler specification and faster implementation
Patch field and copper/
fiber connectivity
Enables troubleshooting of network connections and verification of
field terminations
Defined equipment
locations and
cable routings
Incorporate Panduit developed best practices in connectivity, cable
management, wiring, and grounding in a secure enclosure to ensure
network reliability
Isolation barrier
Segregates higher line voltage from lower voltage switch for increased safety
Bonding provisions
and grounding bar
Ensure path to ground to protect personnel and equipment
Gland plate
Allows quick and easy access to machine ingress points into enclosure
Mounting flexibility
Bolt in place flange mounting for NEMA applications; optional direct mount
through back wall installation maintains NEMA rating when supplied sealing
washer is used; reversible door for left or right-hand opening
Detailed installation
guide
Provides easy, repeatable design instructions assuring consistency and
saving time on the job-site
Pre-Configured Network Zone System
3-DIN rail, mild steel,
UTP copper: Z23C-S
3-DIN rail, mild steel,
STP copper: Z23C-SS
3-DIN rail, 316
stainless steel,
UTP copper: Z23C-6
3-DIN rail, 316
stainless steel,
STP copper: Z23C-6S
2-DIN rail, mild steel,
UTP copper: Z22C-S
2-DIN rail, mild steel,
STP copper: Z22C-SS
2-DIN rail, 316
stainless steel,
UTP copper: Z22C-6
2-DIN rail, 316
stainless steel,
STP copper: Z22C-6S
1-DIN rail, mild steel,
UTP copper: Z11C-S
PanZone
®
NEMA 4X Rated
Compression Fittings
Cable diameters
0.115" – 0.250": PZNF1
Cable diameters
0.230" – 0.395": PZNF2
Cable diameters
0.170" – 0.450": PZNF3
Drain kit: PZNDVK
IndustrialNet
™
TX6
™
Connectors
Category 6 UTP
bulkhead
connector: IAEBH6
Category 6
shielded bulkhead
connector: IAEBH6S
Fiber Uplink Accessories
Surface mount
fiber box: CBXF6BL-AY
LC OptiCam
®
connector: FLCDMCXAQY
LC connector
module: CMDSAQLCZBL
LC patch 10Gig
patch cord: FX2ERLNLNSNM001
Opti-Core
®
Interlocking
Armored Cable: FOPRX12Y
DIN Rail Patching Accessories
Mini-Com
®
Copper
8-Port DIN Rail
Patch Panel: CDPP8RG
Mini-Com
®
Fiber
8-Port DIN Rail
Patch Panel: FDME8RG
Mini-Com
®
Single
Port DIN Rail
Mount Adapter: CADIN1IG
‡
IndustrialNet
™
TX6
™
PLUS Patch Cords
UTP with dust cap: IUTPSP3BL**
UTP without
dust cap: IUTPSPNC3BL**
Shielded with
dust cap: ISTPSP1MBL***
Shielded without
dust cap: ISTPSPNC1MBL***
‡
For standard colors other than International
Gray, replace IG in part number with BL (Black),
EI (Electric Ivory), IW (O White), or WH (White).
*For lengths other than 3 feet (5, 7, 10, 15, or 20
feet) change the length designation in the part
number to the desired length.
**For lengths other than 1 meter (2, 3, or 5
meters) change the length designation in the
part number to the desired length.