Instructions / Assembly

ManualsBrandsPanellift ManualsBuilding materials11 ft. 150 lbs. Drywall Panel Hoist Cable/Sheave Kit

CABLE REPLACEMENT INSTRUCTIONS

B E F O R E installing th e c om ponen ts describe d in t hese instru ctions, determine the

mode l o f

PANELLIFT

Brand Drywall Lift into which the components will be installed.

THEN read an d b ecome familiar wit h t he co mplete Operato r ’s Manual for

that model

of PANELLIFT

Brand Drywall Lift.

The complete Operator’s Manual for the PANELLIFT

Brand Drywall Lift Model 138-2 and 125

is available at www.paragonpromfg.com or call 701-775-0551 to receive a hard copy by mail.

BEFORE installing this component, thoroughly read this set of instructions, make sure you understand them, and

only then follow the step-by-step directions.

FAILURE TO READ AND FOLLOW THESE INSTRUCTIONS could result in failure of the equipment.

Failure of the equipment while the lift is raised can include a sudden and rapid lowering of the lift and

load possibly resulting in serious property damage and/or serious bodily injury.

WARNING

• Use and maintenance of the PANELLIFT

Drywall Lift shall be

limited to authorized personnel who are trained in the proper

techniques for its safe operation and maintenance and who are

familiar with the various hazards of overhead material handling.

• DO NOT ATTEMPT TO USE YOUR PANELLIFT

Drywall Lift

IF ANY PART IS MISSING, DAMAGED OR WORN. ORDER A

REPLACEMENT PART IMMEDIATELY. Using a PANELLIFT

Drywall Lift with missing, damaged or worn components can

result in failure of the unit and possibly severe property damage

and/or serious bodily injury.

• Inspect the Sheaves (Pulleys) and follow the procedure at the

right to replace when worn. Sheave (Pulley) wear can occur

where the cable rides and on the axle. Make sure to inspect

both. Sheave can either be brass or aluminium. The sheave

on the left is badly worn on both the axle and cable groove.

Sheave on right is a new sheave.

• Use only factory authorized replacement parts. Installation of

other parts can compromise the safe design of the PANELLIFT

Drywall Lift and may cause failure of the unit possibly resulting

in serious property damage and/or serious bodily injury.

Questions? - Call Paragon Pro Customer Service at 1-800-448-0822 or 701-775- 0454

Inspect and replace sheaves (pulleys) before replacing the cable.

There are 3 sheaves on the 138-2 Panellift

, one on the frame

and two on the “B” telescoping section. Sheaves should be solid

on their axle and not move up and down or back and forth. To

replace, remove cotter keys and discard old axle and sheave.

Replace with new sheave, axle and new cotter keys.

BE SURE that the cable is fed correctly over the roller sheaves

according to the following instructions:

“B” Section

Sheave

Frame Sheave

Paragon Pro Manufacturing Solutions

7251 S 42nd St• Grand Forks, ND 58201 USA

701-775-0551 Phone • 701-775-0629 Fax

sales@paragonpromfg.com

Quantity: 1

Questions about assembly?

Can’t find a part?

Need some other help?

Call us:

1.800.448.0822

701.775.0551

We’ll get you set up!

Summary of content (4 pages)

PAGE 1
CABLE REPLACEMENT INSTRUCTIONS WARNING BEFORE installing this component, thoroughly read this set of instructions, make sure you understand them, and only then follow the step-by-step directions. FAILURE TO READ AND FOLLOW THESE INSTRUCTIONS could result in failure of the equipment. Failure of the equipment while the lift is raised can include a sudden and rapid lowering of the lift and load possibly resulting in serious property damage and/or serious bodily injury.
PAGE 2
CABLE REPLACEMENT INSTRUCTIONS cont. 2 3) Feed out through near end of sheave pocket LIMITED WARRANTY 2) Feed into top of “B” Section. T ELPRO INC products manufactured by PARAGON PRO MANUFACTURING SOLUTIONS INC are warranted to be free from defects in material and workmanship under normal use for one year from date of purchase.
PAGE 3
ASME Standards for wire rope (cable) inspection and replacement Reprinted with permission from ASME B30.19 Cableways CABLE REPLACEMENT INSTRUCTIONS cont. The following is intended as a helpful guide to the general topic of inspection and replacement of wire rope (cable). It is not intended to be an exhaustive treatment of the topic.
PAGE 4
CABLE REPLACEMENT INSTRUCTIONS continued CABLE REPLACEMENT INSTRUCTIONS continued DO NOT X Starting through the “A” section anchoring “V” from the bottom (1), into the top of the “B” section (2), back out through the sheave pocket at the end nearest the top of the telescoping section (3), into the slot of the “B” section (4), and out a final time through the end of the sheave pocket nearest the bottom of the “B” section (5). X (a) (b) “B” Section 9.