Use and Care Manual

3
Inspection/Installation of Panels
Panels should be inspected on-site, prior to installation.
If there are any defective areas that make the panels
aesthetically unfit for use, contact Panolam immediately.
Upon verification, the defective panel will be replaced by
Panolam. Panolam’s sole responsibility is the replacement
of defective material only, but not for labor or any other
installation expenses.
Panels to be installed per manufacturer’s installation
guide on web site.
Certifications
1. Meets requirements for Class C per ASTM-E84.
2. NSF/ANSI 51 certified.
3. Does not support mold or mildew and meets USDA/
FSIS requirements.
4. GREENGUARD certified.
5. GREENGUARD Gold certified.
6. Meets requirements for CAN/ULC S102.
Cleaning and Maintenance
Cleaning FRP wall and ceiling panels on a regular basis
is recommended in order to avoid soil or dirt build-up.
Recommended cleaners and cleaning methods apply to
both embossed and smooth finishes. FRP panels can
withstand repeated cleanings without adverse effect.
A 5 - 10% solution of trisodium phosphate (TSP) and water,
not to exceed 130º F, can be used successfully for routine
cleaning. Most national home product stores will have TSP
in stock. If TSP is not readily available, a 5 - 10% solution
of household automatic dishwashing detergent or a mild
commercially available cleaner can be used. If a USDA or
FDA approved cleaner is required, a neutral cleaner (pH
range 6.5- 7.5) is preferred. Do not use strong cleaners
or stain removers that contain chlorinated hydrocarbons
or acetone as these will dull the surface finish. Do not
use abrasive cleaners or steel wool as these will mar the
surface.
The surface of the FRP panels is best cleaned using a
sponge or soft bristle brush. Apply the cleaning solution
by working it across the surface in a scrubbing or circular
motion. Thoroughly rinse the area with clean warm water to
remove all traces of the cleaning solution otherwise there
is a possibility of a film build up which will give the panels
a dull, dirty appearance. When using a specialty cleaner,
follow the manufacturer’s instructions. Test a small area
prior to applying to the entire surface.
For hard water deposits, a 10% solution of acetic acid in
cold water may be applied in a scrubbing motion using a
sponge or soft bristle brush. Thoroughly rinse the area after
cleaning.
For oily deposits or difficult substances, mineral spirits may
be used with a clean soft cloth in the affected area. DO NOT
USE strong solvents such as acetone or xylene.
Limited Warranty
Subject to the limitations set forth below, Panolam
®
Industries International Inc. (Panolam) expressly warrants
that our products are reasonably free of defects in material
and workmanship, and when properly handled and
fabricated will conform, within accepted tolerances, to
applicable manufacturing specifications as set forth in
our technical brochure. This warranty shall extend to the
original buyer for a period of twelve (12) months from the
date of shipment of this product by Panolam, and shall not
be assignable by the original buyer. This warranty does not
cover damage resulting from accident, misuse, alteration,
abuse or lack of reasonable care.
Due to the variety of uses and applications to which this
product may be put, and because the manufacturer has
no control over the end products fabricated, the warranty
set forth above is exclusive and in lieu of all warranties,
expressed or implied, in fact or by operation of law or
otherwise, or arising by course of dealing or performance,
custom or usage in the trade, including, without limitation,
the implied warranties of fitness for a particular purpose
and merchantability, and Panolam shall have no obligation
or liability to any person or entity in connection with or
arising from the furnishing, sale, installation or repair, use or
subsequent sale of any product supplied by it.
Our maximum liability arising out of the sale of the products
or their use, whether based upon warranty, contract, tort or
otherwise, shall not exceed the actual payments received by
us in connection therewith.
In no event shall we be liable for special, incidental
or consequential damages, including, but not limited to,
arising hereunder or from the loss of profits, or loss of use
damages, sales of the products.
Headquarters
Panolam Industries International, Inc.
One Corporate Drive, Suite 725
Shelton, CT 06484
1-877-726-6526
www.panolam.com
© 2019 Panolam Industries International, Inc.
4/2019