User's Manual

3. Select “Automatic”, “Always Confirm” or “Never Confirm” by
pressing the Directional Key up or down, then press the OK
Key
[OK].
SENSITIVITY
The Sensitivity setting controls how the voice recognition software determines when a
spoken word is a match. If you frequently experience the messages “Please Repeat...” or
“No Match Found,” adjust the sensitivity toward Reject Less. If you frequently
experience false activations (when the phone recognizes a name you didn’t say), adjust
the sensitivity toward Most Sensitive.
1. From standby mode, press the OK Key [MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 2. Tools,
1. Voice Commands.
2. Press the Right Soft Key
[Settings], “3. Sensitivity”.
3. Select “Most Sensitive”, “ Recommended” or “Least Sensitive” b y
pressing the Directional Key
up or down, then press the OK
Key [OK].
ADAPTATION
Voice Command is speaker independent, which means that no training or adaptation
is required. Some users with heavy accents or unusual voice characteristics may find
difficulty in achieving high accuracy with speaker independent Voice Command,
so the Adapt Voice feature allows users to dramatically improve the recognition
accuracy through adaptation. Users who get acceptable recognition accuracy will find
no additional benefit to performing the Adapt Voice adaptaion.
1. From standby mode, press the OK Key [MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 2. Tools,
1. Voice Commands.
2. Press the Right Soft Key
[Settings], “4. Adaptation”.
3. Select “1. Adapt Voice” or “2. Reset Voice” by pressing the
Directional Key
up or down, then press the OK Key [OK].
• Adapt Voice: Requires that you make recordings of your voice to customize the voice
recognitions system. It will take a few minutes.
• Reset Voice: Once you finish the adaptation process, you can reset the adaptation
to factory default.
“Reset Voice” menu option only appears after you finish the “Adapt Voice” process.
4. Wait for the beep, and then repeat the sentences using a normal
tone of voice.
78 Chapter 4 − Menu Function
Voice ToolsVoice Tools
5. Repeat steps 1-4. When you are finished with a full session, you
will reach a screen that reads “Adaptation Complete”.
PROMPTS
Allows you to select the voice command system characteristics.
1. From standby mode, press the OK Key [MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 2. Tools,
1. Voice Commands.
2. Press the Right Soft Key
[Settings], “5. Prompts”.
3. Select “1. Mode” or “2. Audio playback” by pressing the Directional
Key
up or down, then press the OK Key [OK].
• Mode: Select the voice command system mode from the following:
- Prompts: For handset to read out voice command prompts.
- Readout: For handset to read out prompts, dialing digits and menus.
- Tones Only: For handset to prompt you with a tone only.
• Audio playback: Allows audio playback to play through the speakerphone or
through the earpiece. Select “Automatic”, “ Speakerphone” or
“Earpiece” with the Directional Key up or down.
CALL ALERT
Provides audible readout of the phone number and/or name (if in your contact list) of
an incoming call.
1. From standby mode, press the OK Key [MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 2. Tools,
1. Voice Commands.
2. Press the Right Soft Key
[Settings], “6. Call Alert”.
3. Select “Ring Only”, “ Caller ID + Ring” or “Name Repeat” by pressing
the Directional Key
up or down, then press the OK Key
[OK].
ABOUT
1. From standby mode, press the OK Key [MENU], the Directional
Key right twice for SETTINGS & TOOLS, and press 2. Tools,
1. Voice Commands.
2. Press the Right Soft Key
[Settings], “7. About”.
3. The VoiceSignal version appears.
4. To return to the previous screen, then press the OK Key
[OK].
Menu Function − Chapter 4 79
Voice ToolsVoice Tools
080716_CDM8950_ECHO.indd 78-79080716_CDM8950_ECHO.indd 78-79 2008.7.16 4:1:51 PM2008.7.16 4:1:51 PM