Preface Welcome to the Pantum Series products! We heartily appreciate your using of Pantum Series products! To protect your vital interests, please carefully read the following statements. Legal Notice Trademark Pantum and Pantum logos are registered trademarks of Zhuhai Pantum Electronics Co.,Ltd. Microsoft®, Windows®, Windows Server® and Windows Vista® are trademarks registered by Microsoft Corporation in the United States or other countries/regions.
Safety Precautions Disconnect the power supply The product should be placed close to or easily accessible to power sockets, so as to allow easy disconnection of power supply! Laser Safety The laser radiation is harmful to the human body. Since laser components are completely sealed in the printer, laser radiation will not leak. To avoid laser radiation, please do not randomly disassemble the printer! The printer follows the provisions of Class 1 laser products under CFR standard.
Precautions Precautions before Using the Printer: 1. Read and understand all instructions; 2. Familiarize yourself with the basic principles associated with operating electrical appliances; 3. Comply with all warnings and instructions marked on the equipment or specified in the manual supplied with the equipment; 4. If the operating instructions conflict with the safety information, please refer back to the safety information, as you may have misunderstood the operating instructions.
16.If you continuously print multiple pages, the surface of the tray will become very hot. Take care not to touch this surface, and keep children away from this surface; 17.The signal wire of the device connected with the printer can not be connected to the outdoors; 18.Please ensure timely ventilation in case of a prolonged use or printing huge amounts of documents in a poorly ventilated room; 19.
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 28.Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 29.The power consumption of the product is 3.
Legal Information This symbol indicates that, at the end of your product’s life, it must not be discarded as domestic waste. Instead, you should dispose of your used equipment at a designated collection point for the recycling of waste electrical and electronic equipment. Ref: EU Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). Please contact your distributor / supplier for further information. This product is suitable for indoor use only.
Table of Contents 1.Before Using the Printer .....................................................................................................................1 1.1.Product series introduction ..........................................................................................................1 1.2.Supplied Accessories ...................................................................................................................2 1.3. Product View.................................................
7.3. Cancel printing...........................................................................................................................58 7.4. Printing Mode.............................................................................................................................58 7.4.1. Printing with the Automatic Feeder Tray.............................................................................58 7.4.2. Printing with manual feed tray.........................................................
1.Before Using the Printer 1.1.
1.2.Supplied Accessories Name Parts Toner cartridge Drum component USB Interface Cable Power Cord CD Quick Setup Guide Pantum Warranty Note：• The Pantum Warranty may not be attached in some regions.
1.3.Product View Side view 1 Output Bin For storing the printed paper. 2 Control Panel Indicate printer status to conduct set operation. 3 Output Tray To prevent the printed paper from falling. 4 Front Cover To open the front cover to take out the laser toner cartridge. 5 Manual feed tray For placing mediums that are printed in manual feed tray. 6 Power switch Turn the power on or off and press this button under Ready state to enter energy-saving mode.
10 Paper width deflector of auto feed tray Slide paper width deflector to adapt to paper width. 11 Paper length deflector of auto feed tray Slide paper length deflector to adapt to paper length. 12 Clip of extended tray of auto feed tray For adjustment of length extension of the tray . Rear View 1 USB Interface For connecting product to computer with USB cable. 2 Network Interface For connecting product to network with network cable.
1.4.Laser Toner Cartridge Laser toner cartridge is composed of drum component and toner cartridge.
1.5.Control Panel 1.5.1.Overview of control panel The layout of the printer control panel is shown below: LCD control panel No. Name 1 LCD Display Wi-Fi 2 indicator/save toner indicator 3 Toner cartridge/ status indicator Functions Display operation interface and product information. Indicate Wi-Fi connection status (applicable to Wi-Fi model only). Indicate the on/off of save toner function (applicable to non-Wi-Fi model only).(Please refer to Chapter 1.5.2.
7 Down Scroll through the menus and options . For menu item needs to be input, shift the entry positions from left to right,for example, IP address entry. 8 Back Return to the previous menu. 9 Wi-Fi key/ save toner key 11 Cancel Start Wi-Fi function (applicable to Wi-Fi model only).
Press this button for more than 2s to cancel current printing operation under normal printing condition. Cancel/continously press key 3 Press this button to continue the current printing operation, or press this key for more than 2s to cancel the current printing operation when paper feed fails or it is lack of paper. Press this button for more than 2s to print information page at idle state. 1.5.2.Indicator function of control panel 1.5.2.1.
4 5 6 Orange indicator blinks Low toner warning Orange indicator normally on Toner cartridge error (uninstalled ink cartridge, unmatching ink cartridge, invalid toner cartridge) Red indicator normally on Printer errors such as paper error(paper out, paper jam, paper feed failure), opened front cover 1.5.2.2.Indicator status display of LED control panel Display meanings of drum component/paper status indicators are as follows: No.
Display meanings of toner cartridge/status indicator are as follows: Display of toner cartridge/status indicator Status Status description 1 Die out Sleep mode 2 Green indicator normally on Printer is ready 3 Green indicator blinks Warming up, printing, print cancelling 4 Red indicator normally on Printer errors such as opened front cover 5 Orange indicator normally on Toner cartridge error (uninstalled ink cartridge, unmatching ink cartridge, invalid toner cartridge) 6 Orange indicator b
2.Paper and Print Media 2.1.
Please note the following matters when selecting the print media: 1. Desired print effect: The print media selected should meet the requirement of the print tasks. 2. Surface smoothness: The smoothness of the print media may affect the sharpness of the print outcome. 3.Some print media may meet all the use guidelines contained herein, but they still can not bring satisfactory effect.This may be due to incorrect operation, inappropriate temperature and humidity,or other factors beyond the control of Pantum.
2.3.Loading Paper 2.3.1.Loading into the Automatic Feeder Tray 1. Slide out the automatic feeder tray from the printer. 2. Slide the clip of extended tray of auto feed tray, paper length deflector and paper width deflector to the slot suitable for paper size, in order to match paper length and width. Note： • Do not overly squeeze the "paper length guide" and "paper width guide", otherwise it could easily lead to deformation of paper. 3.
4. Raise the output tray to avoid the printed paper from slipping and falling, or immediately remove the printed document after the printing is complete. Note： • It is recommended that you raise the output tray to prevent the paper from slipping and falling after printing. If you choose not to raise the output tray, we recommend that you immediately remove the printed paper from the printer.
3. Slide the paper deflector of manual feed tray to match the two sides of paper. Do not use excessive force;otherwise, paper will be made jammed or skewed. 4. Put a flat printing medium into the manual feed tray with both hands. Note： • The printer will enter manual feed mode automatically when you put papers inside the manual feed tray. • Please put one printing medium inside the manual feed tray each time and put in another piece after finishing printing.
2.4.Non-printable Area The shaded area indicates the non-printable area. Usage Paper Size Top and bottom margins (A) Left and right margins (B) A4 5mm(0.197inch) 5mm(0.197inch) Letter 5mm(0.197inch) 5mm(0.197inch) Printing 2.5.Paper application rules • Rough textured, uneven, oil stained and extremely smooth paper will make printing effect poor. • Please make sure that there is no dust, fluff, etc. on the paper. • Paper shall be put on a flat surface and stored under a cool and dry environment.
3. Driver installation and uninstallation 3.1. How to install Windows printer driver Windows driver installation software provides two installing methods: one-click installation and manual installation.We recommend one-click installation, which can help to install driver automatically in a faster and more convenient way.If you have any difficulty in using one-click installation, please try manual installation.
5. After the installation, click “Print &Test Page” button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.1.2. Method II: Connect the printer via wired network 1. Turn the power of printer and computer on. 2. Connect the computer to wired network. 3. Connect network cable to the network interface of printer, to make sure the printer is connected to computer network (please refer to Chapter 4 for network setup). 4.
• Windows 10 system: When the “DVD RW driver” window pops up from the right top corner of computer desktop, click anywhere in the window, then click “Autorun.exe” to run the installation procedure. Note: • Some computers may be unable to auto play the CD beacase of system configuration. Please double click "Computer" icon, find "DVD RW driver", then double click "DVD RW driver" to run the installation procedure. 5.
• If your software has searched several printers, click on the”One-click intallation” button, and the printer list interface will pop up. Please select the printer that you need according to your printer wired network IP address or host ID.
Note:• If the printer you need is not shown in the list, please click “Refresh” button to search again. If it is not found, please check if the printer and computer are in the same network. (Please see Chapter 5.3 for how to check). • When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver. If you need to install the printer driver with the host ID, please check the option “Install the printer in the list with host ID”.
4. Click on the “I agree” button on the right buttom corner after reading the license agreement and enter into driver installation interface. 5. Click the “One-click installation” button in Method III to install driver software. Note: • You can put your mouse cursor in the “One-click installation” button to check the popup information in order to confirm if the current printer is the one you need to install through IP address before you click the button.
• If your software has searched several printers, click “One-click intallation” button, and the printer list interface will pop up. Please select “Configure printer with Wi-Fi via USB and install” and select USB printer, click “Confirm” button and enter into installation process to complete automatic network configuration and driver installation. Note: • When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver.
II. Connect computer to router via network cable 1. Connect computer to router via network cable. 2. Connect the printer to computer via USB cable, then power the printer on. 3. Place the attached installation CD in the computer CD-ROM: • Windows XP system: automatically run the installation procedure. • Windows 7/Vista/Server 2008 system: Pop up “Autoplay” interface, click “Autorun.exe” to run the installation procedure.
• Click on the “One-click installation” button if your software has only searched only one printe, and the wireless network configuration interface will pop up, input the SSID and password that you need, then click “Confirm” button, and enter into installation process. The process may need some time, and the duration is related to your computer configuration, please wait patiently. • If your software has searched more than one printers, the printer list interface will pop up.
Note:• When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver. If you need to install the printer driver with the host ID, please check the option "Install the printer in the list with host ID". 6. After the installation, click “Print &Test Page” button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.1.3.1.2.
2. Connect computer to the Wi-Fi Direct network of the printer (please refer to Chapter 5.2.2.2 for setup method). 3. Place the attached installation CD in the computer CD-ROM: • Windows XP system: automatically run the installation procedure. • Windows 7/Vista/Server 2008 system: Pop up “Autoplay” interface, click “Autorun.exe” to run the installation procedure.
6. After the installation, click “Print &Test Page” button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.1.3.2. The printer is already connected to wireless network 1. The printer is already connected to wireless network, you can print the “Network configuration page” to check.(See Chapter 9.4 to for how to print). 2. Connect the computer to printer network. 3.
Note:• You can put your mouse cursor in the “One-click installation” button to check the popup information in order to confirm if the current printer is the one you need to install through IP address before you click the button. • You can check the printer IP address through “Network configuration page” (Please see Chapter 9.4 for how to print) • Click on the “One-click installation” button to enter installation process if your software has searched only one printer.
• If the software has searched several printers, the printer list interface will pop up. Please select the printer you need according to your printer wired network IP address or host ID . Note:• If the printer you need is not shown in the list, please click “Refresh” button to search again. If it is not found, please check if the printer and computer are in the same network. (Please see Chapter 5.3 for how to check).
6. After the installation, click “Print &Test Page” button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.2. Manual installation • Before installing the drive, you need to learn about printer model by printing printer information page out and check the product name (please refer to Chapter 9.4 for printing methods). 3.1.2.1. Installation via USB connection 1. Connect the printer to computer via USB cable, power the printer and computer on. 2.
7. The software installs the driver automatically and the installation process may need some time. The duration is related to your computer configuration, please wait patiently. 8. After the installation, click “Print &Test Page” button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.2.2. Installation via wired network connection 1. Turn the power of printer and computer on. 2. Connect the computer to wired network. 3.
9. The installation software will search the printer automatically and the searching process may need some time. 10. After finishing searching, select the printer that needs to be connected and click “Next”. Note: • If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again. • When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver.
3.1.2.3.1. Installation in basic structure mode 1. Connect computer to access point (wireless router). 2. Connect the printer to computer via USB cable, then power the printer on. 3. Place the attached installation CD in the computer CD-ROM: • Windows XP system: automatically run the installation procedure. • Windows 7/Vista/Server 2008 system: Pop up “Autoplay” interface, click “Autorun.exe” to run the installation procedure.
8. 8. Select “Yes, I want to configurate the printer’s wireless network” on the wireless setup window popped out, and operate according to the prompts to set up the printer to wireless network (please refer to Chapter 5.1.1 for setup method). 9. The installation software will search the printer automatically after wireless network is configured successfully. The search process may need some time. 10. Select the printer needs to be connected and click “Next”.
11. The software installs the driver automatically and the installation process may need some time. The duration is related to your computer configuration, please wait patiently. 12. After the installation, click “Print &Test Page” button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.2.3.2. Installation in Wi-Fi Direct mode 1. Turn the power of printer and computer on. 2.
8. Select “No, the printer has been connected to wireless network” on the wireless setup window popping out, and then click “Next”. 9. The installation software will search the printer automatically and the searching process may need some time. 10. Select the printer needs to be connected and click “Next”. Note: • If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again.
11. The software installs the driver automatically and the installation process may need some time. The duration is related to your computer configuration, please wait patiently. 12. After the installation, click "Print &Test Page" button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.3. Method of driver unistallation Windows 7 is taken as the example in the following operation.
3.2. Mac system driver installation • Driver installation under Mac system is divided into 2 steps, driver installation and adding a printer. If you are going to print in AirPrint mode, there is no need to install a driver and you just need to add a printer directly. • When you are installing a driver with wired or wireless network, you may need to know the Bonjour name of printer. Please print the “Network setup page” to view it. (Please refer to Chapter 9.4). 3.2.1.Driver installation Mac 10.
5. Click “Agree” on the prompt window popping out to accept the licensing agreement. 6. Click “Install”. 7. Input computer password and click “Install Software”. 8. Click “Continue Installation” on the prompt window popping out. 9. The system will finish driver installation automaticall . • If using a USB cable to connect a computer with a Wi-Fi model printer, a wireless network configuration prompt window will pop up during driver installation, as shown in following picture.
3.3.Add printer to Mac system 3.3.1.Add up the printer via USB 1. Connect the printer to computer with USB cable and then turn power on. 2. Enter the “System Preferences” – “Printers & Scanners” of computer. 3. Click button to select “Add Printer or Scanner”. 4. Select printer and then select the corresponding printer mode from the “Use” menu popping out. 5. Click “Add”. 3.3.2.Add up the printer via wireline connection 1. Turn the power of printer and computer on. 2.
3. Enter the “System Preferences” – “Printers & Scanners” of computer. 4. Click button to select “Add Printer or Scanner”. 5. Select printer and then select the corresponding printer mode from the “Use” menu popping out. 6. Click “Add”. 3.3.4. Add AirPrint printer 1. Turn the power of printer and computer on. 2. Make sure the connection between printer and computer is set up (USB connection or network connection). 3. Enter the “System Preferences” – “Printers & Scanners” of computer. 4.
4. Wired network setup (applicable to wired network models) In case printers support wired network printing, they can be connected to network to control printer to print in wired network mode. 4.1.Set IP Address The IP address of the printer may be automatically obtained through DHCP function or set manually. 4.1.1.Automatic Setting DHCP automatic setting function is enabled by default on the printer. 1. Connect the printer to the network through a network cable and complete the startup preparation work.
5.Wireless network setup (applicable to Wi-Fi models) Wireless network connection type is divided into basic structure mode and Wi-Fi Direct mode. If you have problems with wireless network setup, please refer to Chapter 5.3 Wireless Network Setup FAQs. Basic structure mode: connecting to a wireless device via router 1. Access point (wireless router) 2. Wireless network printer 3. Computer connecting to access point via wireless network 4.
5.1.1.2.Setup methods of wireless network setup tools 1. Take the wireless network setup tool in computer. 1) Windows system: Click the “Start menu” – “All programs” - “Pantum”- Product name – “Wireless network setup tool”. 2) Mac system: Click “Go” - “Applications” - “Pantum” - “Utilities” - “Wireless Network Configuration Tool” on the computer Finder menu bar. 2. Use USB cable to connect and configure. Select “Yes, I have an USB cable that can be used for installation” in the following interface.
Note: • The SSID you selected should be consistent with the SSID of access point (wireless router) connected to your computer. 2) Please tick “No” to configure other wireless network needed to connect to. Complete configuration according to interface prompt. Note: • At present, the printer supports 3 types of safe modes: none, WEP and WPA/WPA2. 1) None: There is no encryption method used. 2) WEP: Send and receive data via security key by using WEP (Wired Equivalent Privacy).
2.2 The computer is not connected to wireless network Input the SSID (case sensitive) and password of access point (wireless router) in the interface below. Complete configuration according to interface prompt. Note: • If you do not know the SSID of access point (wireless router), please click “Print Wireless Network Information Page” to view the SSID of the needed access point (wireless router).
1) Use WPS method to perform steps below to start wireless network on printer. (Please refer to Chapter 5.1.2 for detailed WPS configuration) 2) Judge if the printer is successfully connected according to the status of Wi-Fi indicator on printer. If configuration failed, please click “Previous” to configure again; if configuration succeeded, please click “Done” to complete configuration.
5.1.2.Wi-Fi Protected Setup (WPS) setup If the access point (wireless router) supports Wi-Fi Protected Setup (WPS), the Wi-Fi key on the control panel of printer and WPS key on access point (wireless router) can be pressed in order to connect the printer to wireless network. 5.1.2.1.Preliminary preparations 1. The access point (wireless router) supports Wi-Fi Protected Setup (WPS). 2. A printer that has wireless network function. 5.1.2.2.Wi-Fi Protected Setup (WPS) method 1.
5.2.Wi-Fi Direct mode You can connect wireless client (including the computer and mobile device with wireless network feature) to wireless network printer without using the access point (wireless router). 5.2.1.Preliminary preparations 1. Printer with the Wi-Fi Direct feature. 2.Wireless client (including computer and mobile device with wireless network feature). 5.2.2.Wi-Fi Direct connection The Wi-Fi Direct connection feature of printer must be on if it is needed.
3. Select “Advanced” and then select “Wi-Fi Direct” in advanced WLAN interface. 4. Select printer SSID on direct interface to launch a connection invitation. 5. Press “OK key” to confirm connection when the panel lead to prompts whether to connect to start Wi-Fi Direct connection. Note: • In case of auto connection mode, the mobile device will start to connect automatically after initiating connection invitation without panel confirmation. 5.2.2.2.
2. SSID cannot be found when network is connected • Inspect if the power switch of access point (wireless router) is turned on. • The printer cannot find the SSID of the access point (wireless router) you need to connect, please check the SSID of access point and try to connect again. • Every time when the setup of access point (wireless router) is changed, you must set up the wireless network of printer again. 3.
6.Web server You can manage printer setup via the embedded Web server. 6.1.Visit the embedded Web server 1.Turn on the power of printer and computer. 2.Connect the printer to network to ensure that the printer is connected to the network where the computer is connected to (please refer to Chapter 4 or Chapter 5 for network setup method). 3. Input the IP address of printer in the address bar of Web browser to visit the Web server imbedded in printer.
6.2.1.IP address setup You need to connect your printer to network before IP address setup. 1. In case of wired network model, connect the printer to wired network by connecting to its network interface with network cable. 2. In case of wireless network model, the printer can be connected to wireless network via wireless network setup tools or Wi-Fi Protected Setup(WPS) (please refer to Chapter 5.1.2). 6.2.1.1.
6.2.1.2.IPv6 setup 1.Turn on printer power to connect printer to network. 2.Log in the embedded Web server (please refer to Chapter 6.1 for login method). 3.Click “Settings” – “Network settings” – “Protocol Settings” – “IPv6”. 4.Tick “Enable IPv6 protocol” and “Enable DHCPv6” (ticked by default) and then click “Apply”. You can refresh the browser and view the “IPv6 Local Link Address” and “Stateful Address” in “Wired IP Configuration” interface.
6.2.2.4.Wi-Fi Direct setup 1. Click “Settings” – “Network settings” – “Wireless setup” – “Wi-Fi Direct”. 1) Wi-Fi Direct is off as default. If it needs to be enabled, please tick “Enable P2P pairing” and then click “Apply”. 6.2.3.Machine setup You can add mail address contacts, set up e-mail notification, set up sleep time and recover factory settings via machine setup page. 6.2.3.1.
7.Print 7.1.Print Function You can set the print function through "Start"-"Devices and Printers"- select corresponding printer- right click – set print function in "Printing preferences". Some functions are as follows: Functions Diagram Automatic Two-Sided Printing Collate Print Reverse Print N-in-1 Poster Print(for Windows Operation System only) Zoom Print Custom Size Note： • Windows 7 is taken as example in the above description.
7.2.Print Settings You can set up printing parameters with the following two methods before sending printing work (such as paper type, paper size and paper source). Operating system Windows 7 Mac OS Temporary printing setup change 1. Click “File” menu – “Print” – “Select printer" -“Printer properties” (the detailed steps may differ because of multiple operating systems). Permanent default setup change 1.Click “Start” menu- “Control Panel” – “Devices and Printers”. 2.
Note： • For precautions on loading paper, see Chapter 2. • For the type of media to be printed with the automatic feeder tray,see Chapter 2.1. 7.4.2.Printing with manual feed tray When you put papers in the manual feed tray, the printer will enter manual feed mode. Note： • Manual feed mode means that papers will be fed from the manual feed tray first if there are papers being put inside it. • Generally, the manual feeder tray is used to print on special paper, such as envelopes, transparencies, etc.
7.5.Automatic Two-Sided Printing The printer supports automatic two-sided printing of plain paper. Paper size supported by the automatic two-sided printing: A4,Letter, Legal, Oficio, Folio,16K. Note：• Trying the automatic two-sided printing may damage the printer if some paper media are not suitable for automatic two-sided printing. • Auto duplex printing does not support poster printing. • Please refer to Chapter 2 for paper loading and type of mediums that can be printed via auto feed tray. 7.5.1.
3. Adjust paper size slide to A4 or Letter position to finish setting up. 4. Install the duplex unit in the printer. 7.5.2.How to carry out auto duplex printing 1.Open the print job to be printed from the application (such as a Notepad). 2.Select Print from the File menu.
3. Select printer of the corresponding model. 4. Single click “Preferences” for printing setup. 5. Select the “Duplex” in “Basic” tab and then select “Long Edge” or “Short Edge”. 6. Single click “OK” to finish printing setup. Click “Print” to realize auto duplex printing.
7.6.Fine mode printing The Fine mode is applicable to engineering drawings and fine lines printing. Set up fine mode in the basic page of printer preference After setup, fine printing mode can be realized.
7.7.Mute printing If the Mute Printing is set, the printing noise will be reduced but the printing will slow down to some extent. The operating steps of mute printing are as follows (applicable to printers that are installed via USB connection) Windows 7 is taken as the example in the following operation. The information on your computer screen may differ because of multiple operating systems. 1. Enter the “Start menu” – “Control Panel” –view “Devices and Printers”. 2.
7.8.Auto shut-off setting “Auto shut-off setting” to set off condition and off delay of printer. 1. Enter computer “Start Menu” – “Control Panel” – View “Devices and Printers”. 2. Right click printer, select “Printer properties” in drop-down list. 3. Enter “Secondary Settings” option and set “Auto shut-off setting”. 4. Click “OK” to finish setting. Note: • For printer provided with LCD control panel, users may set auto off function through control panel keys. Please refer to Chapter 9.1.7.
7.9.Open Help Document You can open the "Printing preferences" and click "Help" button (for Windows Operation System only). The help document contains the user guide where you can find the information on print settings.
8.Mobile Print 8.1.Android device mobile printing 8.1.1.Pantum Pantum Print is an application free of charge, by which you can directly print TXT, PDF, office documents, pictures and Web in your mobile phone or Tablet PC. 8.1.1.1.Operating systems and Apps supported by Pantum Mobile Print, Mobile Scan and Mobile Fax of Pantum are applicable to Android OS 4.4-8.0, iOS 6.0 or later with a resolution of 480*800dpi or above. 8.1.1.2.How to download Pantum App 1.
4.Select the function you need and set it up to meet your function needs. Note： • If printing fails, please inspect if the Android device is connected to the wireless network where the printer is connected to. • If the Android mobile device did not detect any printer, check whether the printer is powered on and the printer is turned on. • For more details, please refer to the mobile print user guide attached. 8.1.2.
1. Turn on printer power. 2. Connect the Android mobile device with wireless network of the printer (Please refer to Chapter 5 for how to connect). 3. Open the files you need to print with Adobe Reader on the Android device. 4. Click . 5.Tap "Print". 6. Please make sure the Pantum printer is selected. If you selected other printer (or failed to select any printer), please tap the pull-down menu of printer, and select your Pantum printer. 7.Set printing parameters, e.g. print pages. 8.Tap "Print".
Note： • For some mobile devices, NFC antenna may not be on their backsides. Before touching,please check the position of the NFC antenna of your mobile device. • If the mobile device is not installed with Pantum App, the Pantum App download link will pop out automatically. Try again after downloading and installing the App. 3. Select the content to be printed and set printing parameters according to needs. 4. Click print and the printer will start to print. 8.2.iOS device mobile printing 8.2.1.
4. Select corresponding option in the main menu (e.g.: print from the album), tick the picture you need to print and then click . 5. Select the printer needs to be connected, set printing parameters and then click the “Print” button, the printer will start to print. Note： • If printing fails, please inspect if the iOS device is connected to the wireless network where the printer is connected to.
8.2.2.3.How to use AirPrint mobile printing The printing steps may varied by applications, taking PDF as an example for explanation. 1. Turn on printer power. 2.Connect the iOS mobile device with wireless network of the printer (Please refer to Chapter 5 for how to connect). 3. Open the files you need to print in the format of PDF on the iOS device. 4. Click . 5.Tap "Print". 6. Please make sure the Pantum printer is selected.
9.General Settings This Chapter mainly introduces some general settings. 9.1.System Setting 9.1.1.Language Setting "Language Setting" is used to select the language to be displayed on the control panel. 1) Press "Menu" to enter the Menu Settings interface. 2) Press "OK" to select the "1.System Setting" option. 3) Press “OK” key to select “1.
9.1.2.Sleep Time Setting Sleep mode can reduce the energy consumption of printer effectively, and “Sleep time setting” can be made in the idle time before the device enters sleep mode. 1) Press "Menu" to enter the Menu Settings interface. 2) Press "OK" to select the "1.System Setting" option. 3) Press direction key “▲” or “▼” to select “2. Sleep time Set” option, and press “OK” key to set the corresponding sleep time.
9.1.4.Mute printing Set mute mode to realize low speed printing with low noise. When mute mode is “on”, printing will be in a low speed. This mode is “off” by default. 1) Press "Menu" to enter the Menu Settings interface. 2) Press "OK" to select the "1.System Setting" option. 3) Press direction key “▲” or “▼” and select “4. Mute printing” option and press “OK” key to turn on/off this mode.
9.1.5.Restore Factory Settings “Recover factor settings” is used to recover the default settings of printer. The printer will restart itself automatically after recovering factory settings. 1) Press "Menu" to enter the Menu Settings interface. 2) Press "OK" to select the "1.System Setting" option. 3) Press direction key "▲" or "▼" to select the "5.Restore Set" option and press "OK". Note： • Factory settings of network printer can be recovered via embedded Web server (please refer to Chapter 6.2.3.3).
9.1.7.Auto shut-off setting “Auto shut-off setting” to set off condition and off delay of printer. 1) Press "Menu" to enter the Menu Settings interface. 2) Press "OK" to select the "1.System Setting" option. 3) Press direction key “▲” or “▼” to select options of “6.Auto off set”, press “OK” to set off condition and off delay. Note: Set auto off condition: • Shutdown under no-port state (default configuration): no port is connected, Wi-Fi function deactivated, printer is under standby or sleep mode.
9.2.Network Settings You can check or set network status via network setting. 1) Press "Menu" to enter the Menu Settings interface. 2) Press direction key “▲” or “▼” and select “3. Network Set” option and press “OK” key to set “Wired network setting”, “wireless network setting” and “Wi-Fi Direct”.
9.3.Network Information You can check the network status through Network Information.. 1) Press "Menu" to enter the Menu Settings interface. 2) Press direction key “▲” or “▼” and select “4. Network Info” option and press “OK” key to view “wired network information”, “wireless network information” and “Wi-Fi Direct information”.
9.4.Print information report You can print information report by operating control panel. These pages can help you to learn about product information, and diagnose and solve product failures. 1) Press "Menu" to enter the Menu Settings interface. 2) Press direction key “▲” or “▼” and select “5. Prt Info Rept” option. 3) Press “OK” key to enter information report print. You can print product report according to needs.
10.Routine Maintenance Note： • Printer appearance may differ because of different models and functions, so the schematic diagram is only for your reference. 10.1.Cleaning the Printer Note： • Please use mild detergents. • Some parts of the printer may still be hot for a short period after use. When opening the front cover or rear cover to clean the parts inside the printer, please do not touch the parts in the shaded area as shown in the following picture. 1.
Note： • When removing the toner cartridge, put the toner cartridge in a protective bag or wrap it with thick paper to avoid direct light damaging the toner cartridge. 3.Clean the inside of the printer by gently wiping the shaded area, as shown in picture,with adry and lint-free cloth. 4.Wipe the LSU lens of printer gently with dry lint cloth. 5.Open the auto feed tray and wipe the pickup roller gently with dry lint cloth.
10.2.Toner cartridge and drum component component maintenance 10.2.1.About toner cartridge and drum component component 1. Application and maintenance of toner cartridge Please use the original toner cartridge for better printing quality. Please pay attention to the following items while using the toner cartridge: • Do not take the toner cartridge out of its package unless it will be used immediately.
Toner cartridge replacement steps: 1.Power off the printer. 2. Open the front cover and take the laser toner cartridge out along the track. 3. Press the blue button on the left side of drum component with left hand and lift the toner cartridge handle with right hand at the same time to take the toner cartridge out. 4. Open the package of the new toner cartridge and hold the toner cartridge handle to shake it left and right for 5 – 6 times, so that the toner inside can be uniformly dispersed.
5. Pull the seal out and take the toner protection cover out. 6. Install the drum component along the inner track to finish installing toner cartridge. 7.Take the drum component with toner cartridge installed and install it inside the printer along the inner track of printer to finish installing. 8. Close the front cover. Drum component replacement steps: 1.Power off the printer. 2. Open the front cover and take the laser toner cartridge out along the track.
3. Press the blue button on the left side of drum component with left hand and lift the toner cartridge handle with right hand at the same time to take the toner cartridge out. 4. Open the package of new drum component, take the protection device of drum component, and put the drum component on a horizontal table. 5. Install the drum component along the inner track to finish installing toner cartridge. 6.
11.Troubleshooting Please read this section carefully. It may help you to solve common problems encountered during the printing process. If the problems persist, please contact Pantum Aftersales Service Centre. Prior to handling common problems, first check that: • The power cord is connected correctly and the printer is powered on. • All of the protective parts are removed. • The toner cartridge is installed correctly. • The paper is correctly loaded into the tray.
3. After taking papers jammed out, please reinstall the paper tray inside the printer and close the front cover,then the printer will recover printing automatically. 11.1.2.Paper jam of manual feed tray 1.Gently pull the jammed paper out. 2. After taking papers jammed out, open and close the front cover and the printer will recover printing.
11.1.3.Middle jam Note： • When papers jammed in the middle are taken out, please pay attention and do not touch the shaded area shown below, in order to avoid burn. 1. Pull paper tray out. 2.Gently pull the jammed paper out. 3. Install paper tray.
4.Open the front cover. 5. Take the laser toner cartridge out along the track. (For the purpose of preventing printing quality from affecting by the exposure of photosensitive drum, please put the laser toner cartridge inside the protection bag or warp it with thick paper). 6. Gently pull the jammed paper out. 7. After taking out papers jammed, install the laser toner cartridge again and close the front cover, then the printer will recover printing.
11.1.4.Paper Jam in the Fuser Unit Note： • When papers jammed in fuser unit are taken out, please pay attention and do not touch the shaded area shown below in order to avoid burns. 1. Open the rear cover. 2. Open the fuser door using the handles on both sides. 3. Gently pull the jammed paper out.
4. After taking papers jammed out, close the back cover and open the front cover and then the printer will recover printing. 11.1.5.Duplex Unit Jam 1.Remove the duplex printing unit from the back of the printer. 2.Remove the jammed paper from the duplex unit. 3. If the paper does not come out along with the duplex unit, open the tray and remove the jammed paper directly from the bottom.
4. After taking papers jammed out, install the duplex unit back and inspect other parts to the product.If it can be ensured that there are no jammed papers, open and close the front cover and then the printer will recover printing automatically. Note： • After all papers jammed are taken out according to the above steps,close the front cover and tidy the papers in paper tray, then the printer will recover to print automatically.
11.3.Common Troubleshooting 11.3.1.Common Problems Problem Cause Solution Problems with the Printer The printer does not work The cable between the computer and the printer is not connected properly. Error in specifying the print port. The printer is offline and User Guide of Printer is checked. The printer has not recovered from an internal error, such as a paper jam, paper empty, etc. Driver program of printer is not installed correctly. Disconnect and then reconnect the printer cable.
Too many papers in paper tray. The print media is out of the supported media range. Paper Jam There is foreign matter in the paper path. The feed roller is dirty. Internal parts failure. Take the excessive papers out from paper tray; please print with manual feed tray if special printing medium is used to print. Take the excessive papers out from paper tray; please print with manual feed tray if special printing medium is used to print. Clean the paper path. Clean the feed roller.
• The print media does not meet the usage specifications, for example the media is damp or too rough, or has been used previously. White spots • The paper path is dirty. • It is suggested to replace the original toner cartridge. • The print media does not meet the usage specifications, for example the media is damp or too rough, or has been used previously. • Please use printing medium within the specification scope, and use manual feed tray for printing in case of special medium.
• The print media has been loaded incorrectly. Skewed pages • The paper path of the printer is dirty. • Clean the paper path inside the printer. • The print media has been loaded incorrectly. • The print media does not meet the usage specifications. Wrinkled paper • Ensure the correct loading of the print media. • Ensure the correct loading of the print media. • Please use print media within the specification range. • Clean the paper path inside • The paper path of the printer is dirty. the printer.
12.Menu Structure With the help of menu structure of this printer on the panel menu, you may know and set various functions. The steps of printing are as follows: 1) Press "Menu" to enter the menu setting interface. 2) Press "▲" or "▼" to select "Prt Info Rept". 3) Press "OK" and then "▲" or "▼" to select "Menu Struc Pg". 4) Press "OK" to print.
13.Product Specifications Note： • Specification values vary slightly from printers with different models with different functions ,and product specifications vary from different countries and regions. • These values are based on the initial data. For more information about the latest specifications,please visit: www.pantum.com. 13.1.Overview of the Specifications Product Size(W*D*H) 333mm*355mm*215mm Product Weight 6.
Microsoft Windows XP/ Windows Vista/ Windows 7/ Windows 8/ Windows 8.1/ Windows 10/ Windows Server 2003/ Windows Server 2008/ Windows Server 2012（32/64 Bit） Mac OS 10.7/10.8/10.9/10.10/10.11 Operating system Linux (Ubuntu 12.04/ Ubuntu 14.04) Versions higher than iOS 6.0 (excluding iOS 6.0) Android 4.4-8.0 USB 2.0（High Speed） Communication interface IEEE802.3 10Base-T/100Base-Tx IEEE802.11b/g/n (support WPS) Print Time of First Page ≤8.
Company Name: Magnell Associate, Inc. ( DBA NEWEGG.COM ) Office address:17560 Rowland St.
