PAP A GO!® TireSa fe D1 OE USER'S MANUA L PAPA GO Inc. , All Right reserved . V6 . 11 .
CONTEN TS Packing List ................ ................ ................ ................ ................ ...2 PAPAGOf TireSafe 01 OE Firmware Update ................ ................ ........ 3 Receiver Installation ................ ................ ................ ................ .......4 Sensor Installation .............. ................. ................ ................ ........... 5 Display Functions ................ ................ ................ ............... ............ 6 TPMS Setting ..
External Sensor 4pcs TPMS Receiver 1 pes Combination Wrench 1 pes To lock hexagon nut to sensor. CD ® For grasping the sensor base to Cr1632 Battery 4pcs unscrew the sensor cover when replacing the battery. Ring Needle 1 pes ( To replace silicon seal) CD ® Hexagon Nut Spes (one for backup) To pull out silicon seal. To set silicon seal. PAPACO!" nr-eSafe 010E Ullfll'a MA ttUAL Silicon Seal 4 pes (Spares) If a silicon seal is damaged, please replace it with a spare silicon seal to avoid leakage .
· PAPAGO! TireSafe D10E Firmware Update The TireSafe 01 OE is to be used with several GoSafe dash cams . The following GoSafe models are compatible with the TireSafe 01 OE . Support List : PAPAGO GoSafe PAPAGO GoSafe PAPAGO GoSafe PAPAGO GoSafe PAPAGO GoSafe PAPAGO GoSafe PAPAGO GoSafe 388 mini 368 mini 350 mini S30 51 G 30G 760 Airbag warning "" - ..... -- ... ----------------------- ~ ... --- -------- ... ... ... ---- ---- ...... -- ... ------- ... - .. ------ ... ------- -...
Receiver installation : 1 . Insert the TireSafe 01 OE cable into the da sh cam 's GPS Slot. 2 . To have a better signal , t ry to install Receiver in the top left or top right of the windshield . 3 . Turn on power. 4.0n the TPMS Monitor, follow the following steps to install sensors .
External Sensor Installat ion Remove dustproof cap Fasten the hexagon nut to tire valve . Tighten the sensor with nut wrench in reverse direction. Check if air is leaking with soapy water. Display and 4 sensors are already synced with each other. No need to sync again after insta llation.
Display Functions Please install sensors according to the sequences shown in the following images to avoid any errors related to improper display of tire. Tire Pressure & Temperature display Green: Pressure is normal. White : Start the car engine, no signal on white word . F.L F.R '"') ) r- ~) .e . .... 4 ·' ··-J pSI c... _ R.L -·,.... c~ ~ Blue: Temperature is normal. ..-.. .. . .. .•• .-; c Battery Low I - I .. Red: The battery level is low on 2.0V, please replace battery.
Leakage Warning Red: Tire may have been perforated or damaged. X Sensor Disabled Red: Sensor may be lost or run out of power. TPMS Setting This product is suitable for use in sedans , SUVs, and sports cars with tire pressures no greater than 60 PSI. The device does not support trucks , tow trucks , large commercial vehicles , or trailers. You can adjust pressure and temperature alarm values in Settings . Please click I menu / car safety/ TPMS .
Tire Temperature Unit Switching Choose from tempe rature u n it display options (° C and oF). 0 Tire temperature unit High/Low Pressure Alarm Value Setting Manually change high/low settings for pressure alarm. Press UP/DOWN button to adjust the value . (High pressure default setting : 46Psi ; Low pressure default setting : 26Psi.) 0 01/02 TPMS Tire pressure unit Tire temperature unit The max tire pressure The min tire pressure :!::> _.
High Temp eratu re Alarm Value Settin g Manu ally chang e high settin g for high tempe rature alarm . Press UP/DO WN button to adjus t value . (Facto ry defau lt 149° F.) (I TPMS 02/02 The max tire tempe rature Sens or Code Learn ing Choos e syncing mode. The display shows "F.L .- F.R.- R .L. - R .R " and F.L. yellow icon starts pairing . Install F.L. senso r and the displa y will show "Pairin g Succe ss" .
F.L. Press UP/DOWN button to choose the tire position, the current icons will show yellow icon when it starts pairing. F.L. If there is more than one sensor that needs to be synced , install next sensor to pair. Then , click "back" button to save. F.R.
Enlarg ed View of Senso r Cover Button battery Cr1632 Sensor Silicon Seal 11
External Sensor Battery Replacement * If sensor is installed already, you do not need to take the sensor off the tire. Simply unscrew the sensor cover from the valve and replace battery. The uncovered sensor Is as follows as ten sensor cover an tighten in clockwise direction. ~ If the sensor is not installed in tire valve, please use the wrench to fix the sensor base. and then unscrew the sensor cover. Battery replacement successful. ___ ;;;;....;:;;..~.-.;.....
Top Reason s for Leakag e in Nonsta ndard Tire Valves Standar d Valve Reason 1: • The valve core 1s even with the edge. The breach in the valve may be causing the leakage, please replace it with a standard valve. • The valve thread length ~ 9mm Reason 2: Reason 3: the valve core is lower than edge , please adjust it with nut wrench. the valve core is higher than edge , please adjust it with nut wrench .
Specification Sensor Receiver Sensor Weight: <1 Og Input Voltage: 3.3V Operating Temperature : -400C Pressure Range:OPsi- 120Psi lOBar- 8Bar Battery Model: CR 1632 Operating Humidity: ~ +850C 5~98% Battery Lifetime: 1 year Static Current: < 0 . 7JJA Operating Current: < 12mA Operating Temperature: -400C ~ + 1250C Pressure Error: ±1 Psi I ±0.1 Bar Temperature Reading Accuracy: ±20C Operating Humidity: 5-98% Sensor Interface Leakage It is usually caused by nonstandard tire valve.
Safety Precautions The system is only suitable for vehicles with tire pressure that is no more than 80 Psi. The safety of tires on any vehicle should not rely solely on the use of this product. Regular tire inspections are still necessary in case of any nail punctures or tire breakage. Stop your vehicle and check for tire safety as soon as the TPMS system alerts you with the system warnings. This system cannot prevent any unpredictable events by any outside forces .
Product registration card I Warranty Card Produit carte redistration I Carte de garantie VB.0 . 3 10 Limited Warranty Statement • • • • • • • • • • • This limited warranty is given only to the original purchaser of the product. The limited warranty shall be restricted to the country/region of product purchase. The limited warranty is only valid and enforceable in countries where the product is sold. The limited warranty shall last for 12 months from the date of original purchase.
