BODYSMITH PROSYSTEM MAiN UNIT 093 PRODUCT ASSEMBLY I[NSTRUCTTON, S~ETS TOOLS I~._EQUIR.E.D FOR ASSEI~BLY 9~16 iqh’CHSOCKET AD~ISTABLE WRENCH RUBBER/VL4.LLET or ~R REVISION: K if you experience any problemw~th the assemblyof this product, plms~ co:atact your ¯ or your PAP~,.
093 BODYSiVfIT~ PROSYSTEM ASSEMBLY PARTS L~ST SORT AND COUNT ALL PARTS BEFORE BEGYNNING ASSEiV[BLY ~AP, D%VARE: I_TCLM NAME/DESCPJPTION 3. 4. 5. 6. 7. "8. 9. I0. II. 12. .13. 14. !5. 16. i7. 18. 19. QTY .~/8X3-//4IN.BOLT ............................................................................................................. 2 3/~,X3 IN.BOLT ................................................................................................................. 14 3/8X2-3/4 IN.BOLT ....................
09.3 BODYS1V][!TH PROSYSTE1V[ ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY " W~LDM-ENTS/’PARTS: ITEM N.~dV[E/DESCR/PTION QTY 2. 3. 4. 5. 6. 7. 8. 9. lO. 11. 12. I3. 14. 15. 16. 17. 18. 19. 20. 21. 22. MAIN UPRIGHT ............................................................ WEIGHT CARP/AGE .................................................... TOPUPRIGHT SUPPOR-T ............................................. BOTTOM (./PPdGHT SUPPOt%T ................................... FRONT UPR.
093 BODYSM]~THPROSYSTEiV~ ASSE1V~BLY INSTRUCTIONS [NIP. ORTANT.: ¯ TIlE BODYSMITH PROSYSTEM MUST BE ASSEMBLED ON A FLAT LEVEL SURFACE TO ASSURE ITS PROPER FUNCTION. PARABODY, INC. STRONGLY RECOMMENDS THAT THIS PRODUCT BE ~SSEMBLED .BY TWO PERSONS TO AVOID POSSIBLE INJURY. ¯ I~.EP ALL LOOSE FRAME -CONNECTIONS LOOSE UNTIL ~NSTRUCTED IN THE ASSEN[BLY STEP SEQUENCES TO ,,SECURELY TIGHTEN 1. Insert six (6) 2 IN. SQ. ENDCAPinto both FRONTUPRIGHTS.
093 BODYSMITi-I PROSYSTEM ASSEMBLY INSTRUCTIONS Attach one (I) 1-1/4 SQ. RUBBER BUMPER to the CENTER of the CARRIAGE STOPon the WEIGHT CARRIAGE. Slide WEIGHTCARRIAGE down over the REARUPRIGHTof the MAINUPRIC-;HT. (NOTE: MAKESURE THAT THE WEIGHTPEG ON THE WEIGHTCAP,.RIAGE IS FACING TOWARDSTFIE FRONT OF THE MACHINE) LOOSELY attach the two (2) PULLEYMOUNT FLATSto the REARand FROthTUPRIGHTS of the MAINUPRIGHT, using two (2) 3//I X 3 IN. BOLTS,two (2) 3/8 .IN. LOCK WASHERS, and two IN. NUTS.
093 BODYSI~tTU 17. PROSYSTEM ASSEMBLY INSTRUCTIONS Attach one (1.) 3/4 X 2 IN. PAP,.AGLIDE St’RIP and one (I) 1-1/2 X2 IN. PARAGLIDE STRIP to ADJUSTABLEKNEESUPPORTas shown in (’DETAIL E) using the following steps: A. Thoroughly ciean all surfaces where the PARAGLIDE STRIPSare to be attached. B. Removethe paper backing from the PARAGLIDE STRIPSand firmly apply them to the shown surfaces. 18. Assemble two (2) ROLLERPADS to the ADJUSTABLEKNEE SUPPORT, using PADSHAr’-I’, and two (2) STARLOCKCOLLARS. 19.
093 BODYSMiTH PROSYSTEM ASSEMBLY INSTRUCTIONS 24. To install SECONDARY CABLE(PB2559-1), start by inserting the end of the CABLE,WITHOUT the WHITE BALL under the FRONT PULLEY in the LOWROWPULLEY HOUSING on the MAIN UPRIGHT. (REMOVE PULLEY FOR EASE OF INSTALLATION) Push the CABLEunder the FRONTPULLEYand through the HOLEof the 1VLAINUPRIGHTto the PULLEYon the UPRIGHTBRACEof the I~L~_IN UPRIGHT.Pull the CABLEuntil the WHITE BALL stops against the FRONTPULLEYand the LOWROWPULLEYHOUSING.
093 BODYS!Vf!TN PROSYSTEM ASSE!VLBLY INSTRUCTIONS ~~ S~ SNAP ~OO~ ~ FASTENED EXERCISES ~EFO~ DOLNG "~ WARNING~’ DO NOT OPERATE TIIIS IV!ACH!NE W!TI-! LAT BAR OFF SAFETY HOOKS EXCEPT DURING I~IGH PULLEY EXERCISES !!! WAR.
TOP UPRIGHT SUPPORT ~ ,.3/8 LOCKWASHE:R I.AT BARHOLE MAIN UPRI BAR HOLDER(2) (~:EI:::~TAIL"F’) ;ERIAL .
\ \ DETAIL’A" 3/Bx 3-~,/~. BOLT (2) NUT TYP. LOCKFh’ASNER WASHERTYP. KNEE SUPPORT (SEE DETAIL NU’r(2). LOCKWASHER (2.) ~/20.D.
(5{~: DETAI L’F" LOWROWFOOT BRACE
