435104 LEG PRESS ADAPTER KIT ASSEMBLY INSTRUCTIONS Part # 6865101 1 Revision: 2/15/00
IMPORTANT NOTES WELCOMETOTHEWORLDOF Serious steel! Please note: * Thank you for purchasing the 435104 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714.
PARTS LIST KEY 1 2 3 4 5 6 7 8 DESCRIPTION FRONT LEG 3-1/2” PULLEY QUICK DISCONNECT LINK KEYHOLE CLEVIS 2” PULLEY SWIVEL SNAP 72”ELASTIC CORD LEG PRESS CABLE PART # 6747603 3116202 3108102 6427101 3118701 3201501 6271801 6747901 QTY 1 2 1 1 1 1 1 1 KEY 9 10 11 12 13 14 15 16 PART # 3102701 3102501 3102802 3102502 3102801 3102902 3102910 3102909 DESCRIPTION 3/8” HEX NUT 3/8” WASHER 3/8” LOCKNUT 1/2” WASHER 1/2” LOCKNUT 3/8 X 2-1/4” BOLT 1/2 X 3” BOLT 3/8 X 1” QTY 2 3 2 4 4 2 4 1 NOTE: The LEG PRESS A
REAR SHROUD FIGURE 2 STEP 2 • If the 445104 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 2.
ELASTIC CORD BASE HEX NUT 3/8” LOCK NUT SWIVEL SNAP 3/8” THREADED SHAFT 3/8 X 1/2” SPACERS (DISCARD) HEX NUT SWIVEL SNAP 3/8” LOCK NUT FIGURE 3 STEP 3 • Remove two 3/8” LOCK NUTS, two 3/8” HEX NUTS, two SWIVEL SNAP (68) (keep elastic cords attached), two 3/8 X 1/2” SPACERS, and one 3/8” THREADED SHAFT from the bracket on the BASE as shown in FIGURE 3. • Discard the two 3/8 X 1/2” SPACERS.
FIGURE 4 BASE HEXNUT 3/8” LOCK NUT SWIVEL SNAP 3/8” THREADED SHAFT 2 3/8” LOCK NUT HEXNUT SWIVEL SNAP STEP 4 • Assemble the two previously removed 3/8” HEX NUTS, two previously removed SWIVEL SNAPS, one 3-1/2” PULLEY (2), and two previously removed 3/8” LOCK NUTS to the previously removed 3/8” THREADED SHAFT as shown in FIGURE 4.
14 3/8 X 2-1/4” BASE 3/8” WASHER 3/8” WASHER 4-1/2” PULLEY 6 2-7/8” L-BRACKET 9 HEX NUT FIGURE 6 3/8” LOCK NUT STEP 6 • SECURELY assemble the previously removed 4-1/2” PULLEY to the BASE using one 3/8 X 2-1/4” BOLT (14), two previously removed 3/8” WASHERS, one previously removed 2-7/8” L-BRACKET, one SWIVEL SNAP (6), one 3/8” HEX NUT (9), and one previously removed 3/8” LOCK NUT. See FIGURE 6.
TOP BOOM 3/8” X 1” 16 FIGURE 7B (WITH 445104 SECOND STACK OPTION) 10 5 11 3/8” LOCK NUT STEP 7B • If the 445104 SECOND STACK OPTION is NOT installed proceed to STEP 8 . • SECURELY assemble one 3/8 X 1” BOLT (16), one 3/8” WASHER (10), one 2” PULLEY (5) and one 3/8” LOCK NUT (11) to the bracket on the TOP BOOM as shown in FIGURE 7B. STEP 8 2 • SECURELY attach one 3-1/2” PULLEY (2) to the FRONT LEG (1) using one 3/8 X 2-1/4” BOLT (14), two 3/8” WASHERS (10), and one 3/8” LOCK NUT (11). See FIGURE 8.
1/2 X 3” 15 12 8 1 13 LEG PRESS FIGURE 9 STEP 9 • SECURELY attach the LEG PRESS to the FRONT LEG (1) using two 1/2” X 3” BOLTS (15), two 1/2” WASHERS (12), and two 1/2” LOCK NUTS (13). See FIGURE 9. • Route LEG PRESS CABLE (8) around the 3-1/2” PULLEY on the LEG PRESS and UNDER the 3-1/2” PULLEY on the FRONT LEG (1) as shown in FIGURE 9.
BASE 8 1 13 12 1/2 X 3” 15 FIGURE 10 STEP 10 • SECURELY attach the FRONT LEG (1) to 425 BASE using two 1/2 X 3” BOLTS (15), two 1/2” WASHERS (12) and two 1/2” LOCK NUTS (13). See FIGURE 10. • Route LEG PRESS CABLE (8) under the 3-1/2” PULLEY on the 425 BASE as shown in FIGURE 10.
FIGURE 11 DETAIL 11 4 8 LEG CABLE LEG PRESS CABLE SEE DETAIL 11 PRESS CABLE LAT CABLE D-RING STEP 11 • Run the LEG PRESS CABLE through the correct hole on the d-ring and attach one KEYHOLE CLEVIS to the end of the LEG PRESS CABLE. See FIGURE 11 & DETAIL 11. (NOTE: If the 445101 SECOND STACK kit is installed, evenly space the LAT & LEG EXT. CABLES on the D-RING) 7 STEP 12 • Assemble one 72” ELASTIC CORD (7) to the KEYHOLE CLEVIS (4) as shown in FIGURE 12.
TOP BOOM 5 7 8 LEG PRESS CABLE FIGURE 12 STEP 12 • Assemble the 72” ELASTIC CORD (7) from the LEG PRESS CABLE (8) around the 2” PULLEY (5) in the TOP BOOM as shown in FIGURE 12. FIGURE 13 STEP 13 • Assemble the ELASTIC CORD(7) from the LEG PRESS CABLE to the corresponding SWIVEL SNAP (6) on the BASE as shown in FIGURE 13.
3/8” X 1” BUTTON HEAD CAP SCREW REAR SHROUD SPRING PIN ADJUSTMENT 3/8” X 1” BUTTON HEAD CAP SCREW FIGURE 14 STEP 14 • SECURELY attach the four previously removed 3/8 X 1” BUTTON HEAD CAP SCREWS to the rear SHROUD. See FIGURE 14. • The 832 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit from the machine. To use, you must slightly push against the foot plates to take tension off the pin.