PARABODY INC. EXS00 BASE UNIT PBFS01 :: - PRODUCT ASSEMBLY INSTRUCTION SHEETS TOOLS REQUIRED" FOR ASSEMBLY: 9/16 INC~ SOCKET 3/4 INCIt SOCKET ADJUSTABLE WRENCH B.AMMER or RUBBER MALLET 3/16 ALLEN WRENCH 5]32 ALLEN WRENCH REVISION: ..W Īf you experience any problems with the assembly of this product, please contact your dealer or your PARABODY Customer Service reprcsentafive at: 1-800-325-9714.
PBFS01 EXS00 BASE ~IT ASSEMBLY INSTRUCTIONS (STEP #I) TIIE INSTRUCTIONS FOR STEP #I ARE TO BE USED WITH DRAWING SHEET #I OF 6. THE PARABODY EXS00 BASE UNIT M’L!ST BE ASSEMBLED ON A FLAT LEVF, L SURFACE TO ASSURE ITS PROPER FUNCTION. PARABODY INC. STRONGLY RECOMMENDS THAT TI-IIS PRODUCT BE ASSEMBLED BY TWO PERSONS TO AVOID POSSIBLE INJURY *** IMPORTANT*** KEEP ALL LOOSE FRAME, CONNECTIONS LO,OSE UNTIL INSTRUCTED IN TI-~ ASSEMBLY STEP SEQUENCES TO " SECURELY TIGHTENI .......... J___ I, , , I .....
PBFS0t EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (S~fEP #3) THE INSTRUCTIONS FOR STEP #,’3 ARE TO BE USED WITH DRAWINGSHLET #4 OF 6. Place each of the two (2) WEIGHTSTACKBUMPERS over the GUIDERODHOLES(RADIUS EDGESFACINGUP) on the WEIGHTSTACKSUPPORTBASE. Insert each of the two (2) GUIDE RODS through the WEIGHTSTACKBUMPERSand into the WEIGHTSTACKSUPPOP.T BASE. (NOTE:Apply thin film of LUBRICATION (PROVIDED) to guide rods by using paper towel or clean hands.
PBFb01 EXb00 BASE UNIT ASSEMBLY INSTRUCTIONS #!) Insert one (1) 2 IN. SQ. ENDCAPinto the BASESEATSUPPORT and carefully place it on its side the floor. o , ~,8X 1Loosely assemble the BASESEATSUPPORTto the MAINBACKSUPPORT,using two (2) "~ 1/4 BOLTS,four (4) 378 WASHERS, two (2) 3/8 LOCKWASHERS, and two (2) 3/8 Insert a 2 IN. SQ. ENDCAPinto the opert end office EASETEESECTION.
PBFS01 EXS00 ASSEIVI.BLY PARTS LIST FOR STEP COUNT ALL PARTS BEFORE BEGINNING ASSEIVIBLY HARDWARE:. ITEM NAME/DESCRIPTION 2. 3. 4. 5. 6. 7. 9. 10. 11. 12. 13. 14, 15. 16. 17.. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29, 30. 31. 32. 34. 35. 36. 37. QTY BAG # v A (PURPLE) i/2 X3-1/2 LG.BOLT ............................................................................................................. 1 ; ...................................................................................... I/2 X3 LG.
PBFS01 E-X~0 ASSEMBLY PARTS LIST FOR STEP #2 COUNT WELDMENTSfPARTS ITEM 2. 3. 4. 5. 6. 7. 8. 9. ALL PARTS BEFOILE BEGINNI~ G ASSEMBI,¥ ~ NAME/DESCRIPTION QTY 1 (PB1818-1) ....................................... ADJUSTABLE PRESTRETCH SLIDE...................... 1 ’ (PB2296-1) ....................................... LEG CURL EXTENSION 1 (PB2299-1) ....................................... ADJUSTABLE PRE STRETCH SUPPORT ............... 1 (PB1809-I) .......................................
EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (~TEP i0. #2) Inserttwo (2) 2 IN. SQ. END CAP intothe TOP and BOTTOMends of the LEG CUI~ EXTENSION. Securelyassemblethe LEG CURL EXTENSIONonto the BASE SEATSUPPORT,usingone (1) I/2 .3 BOLT,andone (I)I/2 LOWHEIGHTLOC]:,INUT. 12. Attachone(1) RUBBERBUMPERto thefront of the necktubeof the BASESEAl[’S]/PPORT approximately whereshown, giving sufficient contact. 13. Assemblethe two (2) ROLLERPADSto the LEG CURL EXTEN:SION, usingone ([) 15 IN.
PBFS01 EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (STIgP #2) THE INSTRUCTIONS FOP, STEP #2 ARE TO BE USED WITH DRAWINGSHEET #2 & #3 OF 6. Securely assemble ~wo (2) 3/8 DIA. x 2 IN. BUSHING PULLEYSinto the TOP BOO[V/SECTION and tl~ee (3) 318 DIA. x 2 Ii~. BUSHING PULLEYS ~nto the MAINBACKSUPPORT,using five (5) 3/8 6-1/2 BOLTS,ten (10) 3/8 WASHERS, and five (5) 3/8 LOCKNUTS. Attach eight (8) PARAGLIDE STRIPS to the ADJUSTABLE PRE STRETCHSLIDE, as shown (DETAILC ONSHEET#2 OF 6), using the following steps: A.
PBFS01 EXS00 BASE U-NIT ASSEMBLY INSTRUCTIONS(~,TEP #2) 24. Attacheight (8) PARAGLIDESTRIPSto the ADJUSTABLESEAT FRAMEand the :BASESEAT SUPPORTas shownin DETAILA andB on the reverse sideof themainassembly drawing for STEP #2, (SHEET #3 of 6), using the following steps: A. Thoroughlyclean all inside and outside surfaces wherethe paraglide strips sre ::o be attached. B. Removethe paper backing fi-om the paraglide strips and finnly apply themto alI of the shown surfaces (8 Places). .
¯ y ’ PARTSLIST FOR STEP PBFS0iEXS00 ASSEIViBL COUNT ALL PARTS BEFORE. BEGIIN-NING ASSEMBL HA~A~:. N~E~ESC~PTION ITE~ I. 2.. 3. ~. 5. 6. ?. 8. 9. I0. 1I. 12. ~.~G~ ~ (Om~G~) ~IGHT STACK BUMPE~ .................................................................... 3/8~.DIA. GUIDE ~OD~S~ATO~ ............................................................. ~IGHT PLATE BUSH~OS .................................................................... ~/~ X 1-I/2 ~X~ADBOLT ................................................
PBFS01 EXS00 ASSEiVEBLYPARTS LIST FOR STEP #4 COUNT ALL PARTS BEFOREBEGINNINGASSEIVEBLY I-IAR_D ~rARE,:. ITEM NAME/DESCRIPTION QTY BAG# ~. (BRO~.~) 2. 3. 4. 8. 9. 10. 11. 1 5/16 XIBOLT .................................................................. 2 3/8 XI-3/4 BOLT ................................................................ 2 5/16 WASI-IEI~ ................................................................. 1 5/16 LOCK WASHER ................................................................
PBFS01 EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS iL~i~r ~.) TIIE INSTRUCTIONSFOP, STEP #4 A_~.E TO BE USED WITH DI%4.W~NGSI-~:ETS#S & #6 OF 6. Assemble the SWIVELPULLEY BRACKETS using (1) 3/8 Dia x 3/4 BOLT, (2) :511 5 WASHER, 3/8 WASHERand (1) 3/8 LOCKNUT(TIGHTEN TILL LOCKEDTHEN BACK[ NUT OFF 1/4 TURN). Looselyassembletwo (2) 3/8 DIA. x 1 IN. LG. BUSHINGPULLEYSintothe SWIVELPULLEY BRACKETASSEMBLY,usingtwo (2) 3/8 x 1-3/4BOLT,m~o (2) 3/8 LOCKWASHERS,m~d two 3/8 NTJTS(SEE DETAILH A/~D E, SHEET #5).
PBFS0! EXS00 BASE UNIT ASSEIVIBLY INSTRUCTIONS (STEP #4) ![! WARNING MAKESURE SN.A-P HOOKS ARE FASTENED BEFORE DOING ET~]~&CISES. !t! WARNING!!! DO NOT OPERATE TId[IS IVIACHINE WITII LAT BA~. OFF SAFETY HOOKS EXCEPTDURING I-IIGI:!PULLEY EXERCISES.ALSO, LAT BAI’,._IS NOT TO BE USED FOR PULL-UPS. ~ !!! ATTENTION USER INSTRUCTION !!! BEFORE DOING ANY EXERCISES, BE SURE TBAT THE CABI,ES AP,.E TAUT BY: 1) ADJUSTING THE ADJUST,.,.
oo
DETA I L ~A" .
INSII3E£/]NNECTION Z. 5.~. E..
EXS’OD BASE UNIT .
REVISIONS 31’.4 ¢_HAF’F LE.~, CURL EXTEN¢,I~3N ROLLER PAD SLEEVE bETA/L"N" ParaBody~ inc. % RAMSEY,MINNESOTA "~ I ~ _ Ass"r, STEP ~’ 1~.,,,,,,’-,* t’ PtSF501 I..,,_,-~_.
UNIT STEP#?_ CONT’D _SHEETS OFG,
~’..’.
"~EE DE "bETAI L’E" ¯..~..::’.’ .....,..:,,.....~;. ¯ . :: : . .’..~....,... ~. WFJ~iT ,’PLATE, C Z PER.. PLA’TE’~ ¯ . ~TA C1¢.
I
i PULLEY ~.
o¢ DETAIL
