Installation Instructions
Table Of Contents
- Part 1: Introduction
- Part 2: Installation
- Part 3: Programming Methods
- Part 4: Access Codes
- Part 5: Zone Programming
- Part 6: Wireless Features
- Part 7: Arming and Disarming Options
- 7.1 Switch To Stay Arming
- 7.2 Stay Arming with Delay
- 7.3 Regular Arming Switches to Force Arming (Not to be used with UL Installations)
- 7.4 Restrict Arming on Battery Fail
- 7.5 Restrict Arming on Tamper Failure
- 7.6 Timed Auto-Arming
- 7.7 No Movement Auto-Arming
- 7.8 Auto-Arming Options (Not to be used with UL installations)
- 7.9 One-Touch Arming (Not to be used with UL installations)
- 7.10 Exit Delay
- 7.11 Bell Squawk On Arm/Disarm with Keypad
- 7.12 Bell Squawk On Arm/Disarm with Remote Control
- 7.13 No Exit Delay When Arming with Remote Control
- 7.14 No Exit Delay Beeps and No Bell Squawk When Stay Arming
- Part 8: Alarm Options
- Part 9: Reporting and Dialer settings
- 9.1 Reporting/Dialer (Enable/Disable)
- 9.2 Report Codes
- 9.2.1 Arming Report Codes
- 9.2.2 Special Arming Report Codes
- 9.2.3 Disarming Report Codes
- 9.2.4 Special Disarming Report Codes
- 9.2.5 Zone Alarm Report Codes
- 9.2.6 Zone Alarm Restore Report Codes
- 9.2.7 Special Alarm Report Codes
- 9.2.8 Zone Tamper Report Codes
- 9.2.9 Zone Tamper Restore Report Codes
- 9.2.10 System Trouble Report Codes
- 9.2.11 System Trouble Restore Codes
- 9.2.12 Special Reporting Codes
- 9.3 Monitoring Station Telephone Numbers
- 9.4 Partition Account Numbers
- 9.5 Reporting Formats
- 9.6 Pager Delay
- 9.7 Event Call Direction
- 9.8 Dialing Method
- 9.9 Pulse Ratio
- 9.10 Bell on Communication Failure
- 9.11 Dial Tone Delay
- 9.12 Maximum Dialing Attempts
- 9.13 Delay Between Dialing Attempts
- 9.14 Alternate Dial Option
- 9.15 Recent Close Delay
- 9.16 Auto Test Report
- 9.17 Closing Delinquency Timer
- 9.18 Power Failure Report Delay
- 9.19 Disarm Reporting Options
- 9.20 Zone Restore Report Options
- 9.21 Telephone Line Monitoring (TLM)
- Part 10: Programmable Outputs
- Part 11: System Settings
- 11.1 Hardware Reset
- 11.2 Installer Lock
- 11.3 Keypad Lockout Feature
- 11.4 Battery Charge Current
- 11.5 Partitioning
- 11.6 System Real-Time Clock
- 11.7 Clock Adjust
- 11.8 Keypad Tamper Supervision
- 11.9 Keypad Audible Trouble Warning
- 11.10 Confidential Mode
- 11.11 Installer Quick Functions Keys
- 11.12 PGM Modules Supervision
- 11.13 Printer Module Supervision
- 11.14 Zone Expansion Bus Module Supervision
- 11.15 Wireless Transmitter Low Battery Supervision
- 11.16 Wireless Transmitter Supervision Options
- 11.17 Reprogram All Expansion Modules
- Part 12: Settings for WinLoad Software
- Part 13: User Operation
- 13.1 Trouble Display
- 13.2 Programming Access Codes
- 13.3 Disarming & Deactivating an Alarm
- 13.4 Regular Arming
- 13.5 Stay Arming
- 13.6 Instant Arming
- 13.7 Force Arming (Not to be used with UL Installations)
- 13.8 Manual Bypass Programming
- 13.9 One-Touch Arming
- 13.10 Keyswitch Arming
- 13.11 Panic Alarms
- 13.12 Auto-Arming (Not to be used with UL installations)
- 13.13 Alarm Memory Display
- 13.14 Programming Chime Zones
- 13.15 Keypad Muting (Not to be used with UL installations)
- 13.16 Keypad Backlight (1686H and 1686V only)
- FCC Warnings
- Index
Spectra 1759MG 37
If you notice a gain or loss in control panel time, calculate the average gain or loss per day and program the opposite amount in
order to automatically correct the time setting every 24 hours.
Example: If a control panel loses 4 minutes per month, this represents an average loss of 8 seconds per day. Therefore,
programming 008 (plus 8 seconds) into section [088] would compensate for the 8-second loss.
11.8 Keypad Tamper Supervision
Section [128]: General Options
Option [7] OFF = Keypad 1 Tamper Supervision Disabled (default)
Option [7] ON = Keypad 1 Tamper Supervision Enabled
Option [8] OFF = Keypad 2 Tamper Supervision Disabled (default)
Option [8] ON = Keypad 2 Tamper Supervision Enabled
The control panel can be programmed to monitor the on-board tamper status of one or two keypads in the system. If Keypad 1
Tamper Supervision is enabled, the control panel will verify the tamper status of a keypad with its keypad zone set as Keypad
Zone 1. If Keypad 2 Tamper Supervision is enabled, the control panel will verify the tamper status of the keypad with its keypad
zone set as Keypad Zone 2. Ensure that the keypad’s on-board anti-tamper switch is enabled. For LED keypads, see Configuring
The LED Keypad on page 8. For LCD keypads, see the appropriate Installation Guide.
Regardless of whether the keypad zones are being used or not, if more than one keypad is set with the same
keypad zone number, Keypad Tamper Supervision will be lost for that keypad zone. For example, if two keypads
in your system have their keypad zones defined as Keypad Zone 1, the control panel will not recognize a Keypad
1 Tamper Supervision Failure.
If a keypad tamper occurs, the control panel can transmit the appropriate Zone Tamper report code (see page 29) as originating
from the zones specified by the Table 10. If the zone (as specified by Table 10) is enabled, the control panel will report the tamper
as originating from the partition where the zone is assigned. If the zone is not enabled, the control panel will send the Zone
Tamper report code as originating from partition 1. A Tamper/Zone Wiring Failure will also appear in the keypad’s trouble display
(see page 42).
When Reassign Keypad Zone 2 is enabled (see page 12), the Keypad Tamper Supervision for Keypad Zone 2 is
lost. Therefore, Keypad Tamper Supervision will
ONLY function on Keypad Zone 1.
11.9 Keypad Audible Trouble Warning
Section [127]: General Options
Option [3] OFF = Keypad Beep on Trouble Disabled
Option [3] ON = Keypad Beep on Trouble Enabled (default)
When enabled, the keypads emit an intermittent beep tone whenever a trouble condition occurs in the system. The intermittent
beep tone remains activated until the user enters the trouble display by pressing the [
TBL] or [TRBL] key. The intermittent beeps
will re-initialize whenever a new trouble occurs or the trouble restores and re-occurs.
11.10 Confidential Mode
Section [126] Options [1], [2] and [3]
Option [1] OFF = Confidential Mode Disabled (default)
Option [1] ON = Confidential Mode Enabled
Option [2] OFF = Keypads activate when an access code is entered
Option [2] ON = Keypads activate when a key is pressed (default)
Option [3] OFF = Confidential Mode Timer is 2 minutes
Option [3] ON = Confidential Mode Timer is 5 seconds (default)
If Confidential Mode is enabled and no actions are performed on the keypads for the time defined by the Confidential Mode
Timer, all the keypad’s LEDs will be off and LCD screens will show “Paradox Family” until either a key is pressed or an access
code is entered. When the system exits Confidential Mode, the keypads will display the system’s status. Confidential Mode is
activated by enabling option [1]. Option [2] regulates whether the keypads will be activated at the touch of a key or only when an
access code is entered. Option [3] determines the amount of time without action before the system enters Confidential Mode (5
seconds or 2 minutes).
Table 10: Zone Tamper Report Code for Keypad Tamper Supervision Failure
Keypad Tamper
1759MG
Keypad 1 Tamper Supervision =
Zone 6
Keypad 2 Tamper Supervision =
Zone 7