Programming Guide
Table Of Contents
- Default Installer Code
- Default System Master Code
- How Do I Enter Programming Mode?
- Decimal and Hexadecimal Programming Table
- Trouble Display
- Data Display Mode (LED Keypads Only)
- Configuring the 1686H, 1686V and 1689 Keypads (V2.0 or higher)
- Zone Programming
- System Timers
- Programmable Outputs
- System Options
- Communication Settings
- Report Codes
- System Settings
- User Code Options
- Reprogram All Modules
- Paradox Memory Key (PMC-3)
- 4-PGM Output Modules V2.0
- Printer Module V2.0
- Voice-assisted Arm/Disarm Bus Module V2.0
- Wireless Features
- Zone Expansion Bus Modules
- User Operation
- Appendix A - Ademco CID Report Code List (Prog.)
- Appendix B - Ademco CID Report Code List (All Codes)
- Bus Module Connections
- Hardware Connections
Spectra 1759MG - 14 - Programming Guide
Bold = Default Setting
Section [133]: Partition 1 Options
Option
OFF ON
[1]
Auto-arm on time N Disabled N Enabled
[2]
Auto-arm on no movement N Disabled N Enabled
[3]
Auto Arming = Regular or Stay N Regular Arming N Stay Arming
[4]
Switch to Stay Arming if no entry delay is opened N Disabled N Enabled
[5]
Stay Arming with Delay Partition 1 (Delay = [070]) N Disabled N Enabled
[6] to [8]
Future use N N/A N N/A
Section [134]: Partition 2 Options
Option
OFF ON
[1]
Auto-arm on time N Disabled N Enabled
[2]
Auto-arm on no movement N Disabled N Enabled
[3]
Auto Arming = Regular or Stay N Regular Arming N Stay Arming
[4]
Switch to Stay Arming if no entry delay is opened N Disabled N Enabled
[5]
Stay Arming with Delay Partition 2 (Delay = [070]) N Disabled N Enabled
[6] to [8]
Future use N N/A N N/A
Section [135]: Dialer Options
Option
OFF ON
[1] & [2]
N see table
N see table
N see table
N see table
[3]
Reporting (Dialer) N Disabled N Enabled
[4]
Dialing method N Pulse Dialing N Tone (DTMF) Dialing
[5]
Pulse ratio N 1:2 N 1:1.5
[6]
If armed, activate bell output on Com. Failure N Disabled N Enabled
[7] & [8]
Future use N N/A N N/A
Section [136]: Dialer Options
Option
OFF ON
[1]
Call back WinLoad N Disabled N Enabled
[2]
Automatic event buffer transmission N Disabled N Enabled
[3]
Contact I.D. report codes N Programmable N All Codes (automatic)
[4]
Alternate dial N Disabled N Enabled
[5]
If no dial tone is present N Continue after 4 sec. N Hang-up after 16 sec.
[6] & [7]
N see table
N see table
N see table
N see table
[8]
Pager Format Transmission Options N Transmit report code
after Pager delay
N Transmit report code
immediately
Telephone Line Monitoring (TLM) Options
[1] [2]
OFF OFF TLM Disabled (default)
OFF ON TLM generates a trouble if armed
ON OFF TLM generates an audible alarm if armed
ON ON Silent alarms become audible
Pager Reporting Format Dialer Options
[6] [7]
OFF OFF 1 call to pager or cellular telephone (default)
OFF ON 2 calls to pager or cellular telephone
ON OFF 3 calls to pager or cellular telephone
ON ON 4 calls to pager or cellular telephone