Programming Guide
Table Of Contents
- Default Installer Code
- Default System Master Code
- How Do I Enter Programming Mode?
- Decimal and Hexadecimal Programming Table
- Trouble Display
- Data Display Mode (LED Keypads Only)
- Configuring the 1686H, 1686V and 1689 Keypads (V2.0 or higher)
- Zone Programming
- System Timers
- Programmable Outputs
- System Options
- Communication Settings
- Report Codes
- System Settings
- User Code Options
- Reprogram All Modules
- Paradox Memory Key (PMC-3)
- 4-PGM Output Modules V2.0
- Printer Module V2.0
- Voice-assisted Arm/Disarm Bus Module V2.0
- Wireless Features
- Zone Expansion Bus Modules
- User Operation
- Appendix A - Ademco CID Report Code List (Prog.)
- Appendix B - Ademco CID Report Code List (All Codes)
- Bus Module Connections
- Hardware Connections
Spectra 1759MG - 15 - Programming Guide
Bold = Default Setting
Communication Settings
Section [137]: Event Call Direction
Option
OFF ON
[1]
Call Telephone #1 for Arming/Disarming Report Codes N Disabled N Enabled
[2]
Call Telephone #2 for Arming/Disarming Report Codes N Disabled N Enabled
[3]
Call Telephone #1 for Alarm/Restore Report Codes N Disabled N Enabled
[4]
Call Telephone #2 for Alarm/Restore Report Codes N Disabled N Enabled
[5]
Call Telephone #1 for Tamper/Restore Report Codes N Disabled N Enabled
[6]
Call Telephone #2 for Tamper/Restore Report Codes N Disabled N Enabled
[7] & [8]
Future use N N/A N N/A
Section [138]: Event Call Direction
Option
OFF ON
[1]
Call Telephone #1 for Trouble/Restore Report Codes N Disabled N Enabled
[2]
Call Telephone #2 for Trouble/Restore Report Codes N Disabled N Enabled
[3]
Call Telephone #1 for Special Report Codes N Disabled N Enabled
[4]
Call Telephone #2 for Special Report Codes N Disabled N Enabled
[5] to [8]
Future use N N/A N N/A
Section #
[140] ___ / ___
TEL1 TEL2
REPORTING FORMATS
1 = ADEMCO SLOW (1400HZ, 1900HZ, 10BPS)
2 = SILENT KNIGHT FAST (1400HZ, 1900HZ, 20BPS)
3 =
SESCOA (2300HZ, 1800HZ, 20BPS)
4 =
ADEMCO EXPRESS (DTMF 4+2)
5 = ADEMCO CONTACT ID (DEFAULT) see option [3] in section [136] on page 14
6 =
PAGER FORMAT
If Hexadecimals (0 to FF) are used to program the report codes, verify that the pager also supports
Hexadecimals. If the pager does not support Hexadecimals, use only the digits 0 to 9.
[141] ___/___/___/___
PANEL IDENTIFIER (WINLOAD SOFTWARE)
[142] ___/___/___/___
PC PASSWORD (WINLOAD SOFTWARE)
[143] ___/___/___/___
PARTITION ACCOUNT NUMBER 1 (For less than 4 digits, use the [FORCE] key to enter blanks.)
[144] ___/___/___/___
PARTITION ACCOUNT NUMBER 2 (For less than 4 digits, use the [FORCE] key to enter blanks.)
[150] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
PC TELEPHONE NUMBER FOR WINLOAD SOFTWARE (32-digits, if less than 32 press [ENTER] to accept)
[151] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
CENTRAL STATION TELEPHONE OR PAGER NUMBER 1 (32-digits, if less than 32 press [ENTER] to accept)
[152] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
CENTRAL STATION TELEPHONE OR PAGER NUMBER 2 (32-digits, if less than 32 press [ENTER] to accept)
[153] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
BACK UP TELEPHONE NUMBER (32-digits, if less than 32 press [ENTER] to accept)
Special Keys for Telephone Numbers
[STAY] = * [MEM] = Switch from pulse to tone dialing or vice versa [FORCE] = Delete current digit
[
BYP] = # [TBL] or [TRBL] = 4-second pause [PG] or [FNC1] = Inserts Blank Space