Programming Guide
Table Of Contents
- Default Installer Code
- Default System Master Code
- How Do I Enter Programming Mode?
- Decimal and Hexadecimal Programming Table
- Trouble Display
- Data Display Mode (LED Keypads Only)
- Configuring the 1686H, 1686V and 1689 Keypads (V2.0 or higher)
- Zone Programming
- System Timers
- Programmable Outputs
- System Options
- Communication Settings
- Report Codes
- System Settings
- User Code Options
- Reprogram All Modules
- Paradox Memory Key (PMC-3)
- 4-PGM Output Modules V2.0
- Printer Module V2.0
- Voice-assisted Arm/Disarm Bus Module V2.0
- Wireless Features
- Zone Expansion Bus Modules
- User Operation
- Appendix A - Ademco CID Report Code List (Prog.)
- Appendix B - Ademco CID Report Code List (All Codes)
- Bus Module Connections
- Hardware Connections
Spectra 1759MG - 25 - Programming Guide
Remote Control User Assignment
Section # Decimal Value Description Default Value
[701] ___/___/___(001-048 = user #) remote control #1 - section [731]* 000
[702] ___/___/___(001-048 = user #) remote control #2 - section [732]* 000
[703] ___/___/___(001-048 = user #) remote control #3 - section [733]* 000
[704] ___/___/___(001-048 = user #) remote control #4 - section [734]* 000
[705] ___/___/___(001-048 = user #) remote control #5 - section [735]* 000
[706] ___/___/___(001-048 = user #) remote control #6 - section [736]* 000
[707] ___/___/___(001-048 = user #) remote control #7 - section [737]* 000
[708] ___/___/___(001-048 = user #) remote control #8 - section [738]* 000
* refer to Remote Control Assignment on page 26.
Button Options
Please note that the User Code assigned to the remote control (sections [701] to [708]) must have the same User
Options and Button Options enabled. For example, if you enable the Force Arming button option you must enable the
appropriate Force Arming user option. Also, if you enable any of the Panic button options, you must enable the Panic
options in the control panel.
Remote Control Button Programming
RC# Section
RC Buttons
Default: ( 1 5 0 0 0 0 0 0 )
1 [711]
_____/_____/_____/_____/______/_____/_____/______
2 [712]
_____/_____/_____/_____/______/_____/_____/______
3 [713]
_____/_____/_____/_____/______/_____/_____/______
4 [714]
_____/_____/_____/_____/______/_____/_____/______
5 [715]
_____/_____/_____/_____/______/_____/_____/______
6 [716]
_____/_____/_____/_____/______/_____/_____/______
7 [717]
_____/_____/_____/_____/______/_____/_____/______
8 [718]
_____/_____/_____/_____/______/_____/_____/______
Button Options Table
Empty Slot [FORCE] - Button disabled
1 - Regular arming
2 - Stay arming
3 - Instant arming
4 - Force arming
5 - Disarm
6 - Disarm when no alarm
7 - Regular arm and disarm
8 - Panic 1
9 - Panic 2
A - Panic 3
B - PGM Activation (Event Group #7, see PGM Programming)
C - PGM Activation (Event Group #8, see PGM Programming)
D - PGM Activation (Event Group #9, see PGM Programming)
MG-REM1
+
+ +
+
+
+ +
+
+
+
+
+
+
+ +
+
+
+ +
+
+
+
+
+
+
+ +
+
+
+ +
+
= These button combinations are not available with the MG-REM1or MG-RAC1 remote controls and cannot be programmed.