User's Manual
Table Of Contents
- Things You Should Know
- Entering Programming Mode
- Installer Quick Keys
- Zone Programming
- Remote Control Button Programming
- System Timers
- On-board Programmable Outputs (PGMs)
- System Options
- Communicator Settings
- Report Codes
- System Settings
- Wireless Transmitter Assignment
- Wireless Output Assignment
- Wireless Keypad Assignment
- Wireless Repeater Assignment
- Wireless Programmable Output (PGM) Settings
- Wireless Supervision Options
- Wireless Repeater Options
- Appendix 1: PGM Event Table
- Appendix 2: Specifications
- Appendix 3: Connection Diagrams
- Power Connections
- Telephone Line Connections
- PGM Connections
- Hardwire Zone Connections
- Connecting the Radio Antenna (MG-6160 only)
- Connecting to a UIP-256
- X10 Transmitter Connections (MG-6160 only)
- Connecting Magellan to WinLoad
- Connecting a Paradox Memory Key (PMC-4)
- Tabletop Mounting
- Mounting Magellan on the Wall
- Appendix 4: Ademco Contact ID Report Codes
- Appendix 5: Automatic Report Code List
8 Programming Guide
† For UL installations, Tamper recognition options must be enabled.
‡ For UL installations, Wireless supervision options must be enabled.
* For UL installations, if the zone is programmed as a wireless fire zone, supervision must be enabled and the check-in supervision time must be set at 80
minutes (section [096] option [7] on page 8).
* For UL installations, if either or both of the hardwired zones are enabled, then section [095] option [3] option must be enabled.
† This feature only applies to Magellan’s onboard zone inputs. Section [095] options [1] and [2] must be ON in order to use this feature.
* This option must be enabled for UL installations.
[094] Zone Options Bold = Default setting
Option OFF ON
[1] Stay delay zones Disabled Enabled
[2] Report zone restore On Bell cut-off On zone closure
[3] & [4] Tamper recognition options † See table
See table
See table
See table
[5] Generate tamper trouble if detected on bypassed zone No Yes
[6] & [7] Wireless transmitter supervision options ‡ See table
See table
See table
See table
[8] Generate supervision trouble if detected on bypassed zone No Yes
[095] Zone Options Bold = Default setting
Option OFF ON
[1] Zone 31 is hardwire zone 1 * Disabled Enabled
[2] Zone 32 is hardwire zone 2 * Disabled Enabled
[3] EOL (End-Of-Line) resistors † No EOL Use EOL resistors
[4] Stay arm siren delay Disabled Enabled
[5] Future use
[6] Live Display Mode for Wireless Keypad (MG32WK) Disabled Enabled
[7] & [8] Future use
[096] General Options Bold = Default setting
Option
OFF ON
[1] & [2] Doorbell 1 tone options See table
See table
See table
See table
[3] & [4] Doorbell 2 tone options See table
See table
See table
See table
[5] Daylight savings time Disabled Enabled
[6] AC power failure warning * Disabled Enabled
[7] Check-in supervision time 24Hrs 80 minutes
[8] RF Jamming supervision * Disabled Enabled
[097] General Options Bold = Default setting
Option OFF ON
[1] Volume boost on entry/exit delay Disabled Enabled
[2] Volume boost in speakerphone mode Disabled Enabled
[3] to [8] Future use Future use Future use
[3] [4]
OFF OFF - Disabled
OFF ON - Trouble only
ON OFF - Disarmed: Trouble only
- Armed: Follow zone’s alarm type (page 4)
ON ON - Disarmed: Audible alarm
- Armed: Follow zone’s alarm type (page 4)
[6] [7]
OFF OFF
- Disabled
*
OFF ON - Trouble only
ON OFF - Disarmed: Trouble only
- Armed: Follow zone’s alarm type (page 4)
ON ON - Disarmed: Audible alarm
- Armed: Follow zone’s alarm type (page 4)
[1] [2]
OFF OFF - Tone 1
OFF ON - Tone 2
ON OFF - Tone 3
ON ON - Tone 4
[3] [4]
OFF OFF - Tone 1
OFF ON - Tone 2
ON OFF - Tone 3
ON ON - Tone 4