6211-I1 Router User’s Guide Document No.
Copyright 2005 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Ave. N.
! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord. 4.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Notice to Users of the Canadian Telephone Network NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
E August 2005 6211-A2-GB21-30
Contents About This Guide 1 2 Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . v Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Product-Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4 5 Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Quick Setup with Auto-Connect Enabled . . . . . . . . . . . . . . . . . . . . . . . 4-1 Quick Setup with Auto-Connect Disabled . . . . . . . . . . . . . . . . . . . . . . 4-3 Quick Setup Advanced Setup ii WAN. . . . . . . . . . . . . . . . . . . . . .
Contents 6 Diagnostics 7 Testing the DSL Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Saving and Restoring the Configuration . . . . . . . . . . . . . . . . . . . . . . . 7-1 Backing Up Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Restoring Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Restoring Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents iv August 2005 6211-A2-GB21-30
About This Guide Document Purpose and Intended Audience This guide contains detailed information about the 6211-I1 router. It is intended for all users of the router. Document Summary Section Description Chapter 1, Introduction Describes the features of the router. Chapter 2, Hardware Installation and PC Setup Shows how to connect the router and set up your PC to manage the router.
About This Guide Product-Related Documents Complete documentation for Paradyne products is available online at www.paradyne.com. Select Support → Technical Manuals. To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 1-727-530-2000.
Introduction 1 Introduction Congratulations on becoming the owner of a 6211 ADSL router. This User’s Guide will show you how to set up the router, and how to customize its configuration to get the most out of this product. Features The 6211 router has the following features: Built-in ADSL modem which offers G.Dmt, G.lite, T1.413, ADSL2, Annex L, and ADSL2+ to meet different linking speeds from your ISP.
1. Introduction — Windows 95b, 98, 98SE, 2000, ME, NT, or XP (Note: Windows 95 requires the installation of the Winsock program, not included. Windows 95 and 98 do not support USB.) — (Optional) An Ethernet hub or switch, if you wish to connect the router to several computers on an Ethernet network. — For system configuration using the supplied web-based program: a web browser such as Internet Explorer Version 6.0 or later. Netscape is not supported.
1. Introduction Front Panel The front panel contains LED indicators that show the status of the unit. B US N LA ITY TIV AC US AT ST R WE PO 05-17610 Figure 1-2. Table 1-1.
1. Introduction Rear Panel The rear panel contains the ports for the router's data and power connections. Table 1-2.
Hardware Installation and PC Setup 2 Overview This chapter provides basic instructions for connecting the router to a computer or a LAN and to the Internet using DSL. The first part provides instructions to set up the hardware, and the second part describes how to prepare your PC for use with the router. It is assumed that you have already subscribed to DSL service with your Internet service provider (ISP).
2. Hardware Installation and PC Setup — If your LAN has more than one computer, you can attach one end of an Ethernet cable to a hub or a switch and the other to the LAN port of the router. Either a crossover or straight-through Ethernet cable can be used. 4. Connect the AC power adapter to the POWER connector on the back of the device and plug the adapter into a wall outlet or power strip. RESET LINE PHONE USB LAN 1 2 3 DEFAULT POWER 4 OR 04-17510 Figure 2-1. Hardware Installation 5.
2. Hardware Installation and PC Setup Table 2-1. LED Indicators This LED . . . Should be: POWER Solid green to indicate that the device is turned on. If this light is not on, check if the power adapter is attached to the router and plugged into an AC power source. STATUS Solid green to indicate that the router can communicate with your ISP via ADSL, or flashing when the router is trying to connect to your ISP. ACTIVITY Flashing when the device is sending or receiving data over the ADSL connection.
2. Hardware Installation and PC Setup Installing the USB Driver The following section applies only if you use the USB connector on the router. If you connect the USB cable between your PC and the router, Windows detects the new hardware and the Found New Hardware Wizard appears on your PC monitor. Follow this procedure: Procedure 1. Choose "Install from a list or specific location" from the Wizard's menu, then click on Next. Figure 2-2.
2. Hardware Installation and PC Setup 2. Insert the supplied CD ROM and use Browse to include the CD drive in the search. Figure 2-3. Search and Installation Options 3. If the Wizard reports a compatibility issue, select "Continue Anyway". Installation of the USB driver proceeds. Figure 2-4.
2. Hardware Installation and PC Setup Figure 2-5. Progress Screen 4. When prompted, click on Finish to close the Wizard. Figure 2-6.
2. Hardware Installation and PC Setup Configuring Your Computer Before you can access the router over the LAN or the USB port, you have to configure your PC's TCP/IP address to be 192.168.1.x (where x is any number between 3 and 254), with a subnet mask of 255.255.255.0. Your router's default IP address is 192.168.1.1. Windows XP PCs 1. In the Windows task bar, click on the Start button, and then click on Control Panel. 2. Double-click on the Network Connections icon. 3.
2. Hardware Installation and PC Setup Figure 2-8. Local Area Connection Properties (Windows XP) 5. In the Internet Protocol (TCP/IP) Properties dialog box, click on the radio button labeled Use the following IP address. Type an address between 192.168.1.3 and 192.168.1.254 in the IP Address field (192.168.1.20 is shown here as an example) and 255.255.255.0 in the Subnet Mask field. Figure 2-9. TCP/IP Properties (Windows XP) 6. Click on OK twice to confirm your changes, and close the Control Panel.
2. Hardware Installation and PC Setup Windows 2000 PCs 1. In the Windows task bar, click on the Start button, point to Settings, and then click on Control Panel. 2. Double-click on the Network and Dial-up Connections icon. 3. In the Network and Dial-up Connections window, right-click on the Local Area Connection icon, and then select Properties. The Local Area Connection Properties dialog box display a list of currently installed network components.
2. Hardware Installation and PC Setup 4. If Internet Protocol (TCP/IP) does not appear as an installed component, click on Add. 5. In the Select Network Component Type dialog box, select Protocol, and then click on Add. 6. Select Microsoft in the Manufacturers box. 7. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click on OK. You may be prompted to install files from your Windows Me installation CD or other media. Follow the instructions to install the files. 8.
2. Hardware Installation and PC Setup 8. After restarting your PC, open the Control Panel window, and then click on the Network icon. 9. Select the network component labeled TCP/IP, and then click on Properties. If you have multiple TCP/IP listings, select the listing associated with your network card or adapter. 10. In the TCP/IP Properties dialog box, click on the IP Address tab. 11. Click in the radio button labeled Use the following IP address. Type an address between 192.168.1.3 and 192.168.1.
2. Hardware Installation and PC Setup Logging in to Your Router This section shows how to connect to the router's web interface, configure settings, and observe some statistics of your Internet connection. 1. Open your Web browser, and type the following URL in the address/location box, and press Enter: http://192.168.1.1 This is the default IP address for the LAN port on the router. A login screen appears. Figure 2-10.
2. Hardware Installation and PC Setup Figure 2-11.
2.
Device Information 3 Status Summary Display the general status report for the router by clicking on Summary under Device Info (Figure 3-1). Figure 3-1.
3. Device Information WAN Display the WAN status report from the by clicking on WAN under Device Info (Figure 3-2). Figure 3-2.
3. Device Information LAN Statistics Display LAN statistics by clicking on LAN under Statistics (Figure 3-3). Figure 3-3.
3. Device Information WAN Statistics Display WAN statistics by clicking on WAN under Statistics (Figure 3-4). Figure 3-4.
3. Device Information ATM Statistics Display ATM statistics by clicking on ATM under Statistics (Figure 3-5). Figure 3-5.
3. Device Information ADSL Statistics Display ADSL statistics by clicking on ADSL under Statistics (Figure 3-6). Figure 3-6.
3. Device Information ADSL BER Test The ADSL Bit Error Rate (BER) test determines the quality of the ADSL connection. The test is performed by transferring idle cells containing a known pattern and comparing the received data with this known pattern to check for any errors (Figure 3-7 and Figure 3-8). Procedure To run a BER test: 1. Click on the ADSL BER Test button. 2. Select the test duration and click on Start 3. Check the result. Figure 3-7.
3. Device Information Figure 3-8. ADSL BER Test — Result Route Obtain the Routing status report by clicking on the Route item under Device Info (Figure 3-9) Figure 3-9.
3. Device Information ARP Display the ARP status report by clicking on ARP under Device Info (Figure 3-10) Figure 3-10.
3.
Quick Setup 4 Quick Setup with Auto-Connect Enabled Auto-connect will automatically detect the first usable PVC and automatically detect PPPoE, PPPoA, and Bridge Protocol (with DHCP Server available). To use auto-connect: Procedure 1. Select Quick Setup. The Quick Setup initial screen appears. Figure 4-1.
4. Quick Setup 2. Select DSL Auto-Connect, then click on Next. The progress information screen appears. 4-2 Figure 4-2. Detecting Available PVC Figure 4-3.
4. Quick Setup Quick Setup with Auto-Connect Disabled Procedure 1. Select Quick Setup. The Quick Setup initial screen appears. Figure 4-4. Specifying VPI and VCI 2. Verify that DSL Auto-Connect is not selected. Specify VPI and VCI as directed by your ISP. Click on Next. 3. Use Advanced Setup to configure the PVC.
4.
Advanced Setup 5 WAN Set up WAN parameters as directed by your ISP. Figure 5-1.
5. Advanced Setup Add Function – ATM PVC Configuration If you want to add a new rule for the WAN interface, click on the Add button. The ATM PVC Configuration screen appears. The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category. Figure 5-2. ATM PVC Configuration Screen Verify the following values with your ISP before you change them. VPI (Virtual Path Identifier) – The valid range is 0 to 255.
5. Advanced Setup Connection Type Screen Select the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use, then click on Next button. Figure 5-3. Connection Type Screen Select a connection type and click on Next.
5. Advanced Setup Bridge Service and Quality of Service Screen This WAN service can be enabled or disabled by clicking in the check box. Enabling QoS for a PVC improves performance for selected classes of applications. However, since QoS also consumes system resources, the number of PVCs is reduced. The default setting for QoS is disabled. If you want to enable QoS service, select the "Enable Quality Of Service" check box. After finishing steps as above, click on the Next button. Figure 5-4.
5. Advanced Setup WAN Setup - Summary Make sure that the settings on the WAN Setup screen match the settings provided by your ISP. If all settings are correct, click on the Save button to save these settings; if not, click on the Back button to make any modifications. If you want to change any item after saving, click on the Edit button to make any modifications. Figure 5-5.
5. Advanced Setup Remove Function If you want to delete a connection from the listed WAN setup, click in the Remove check box next to the item, then click on the Remove button. Figure 5-6. WAN Setup List Finish Function After you change any item in WAN Setup, remember to click on the Finish button to apply the changes and reboot the system.
5. Advanced Setup Local Area Network (LAN) Setup You can configure the DSL Router IP address and Subnet Mask for the LAN interface to conform your LAN's IP Subnet. The Save button only saves the LAN configuration data. The Save/Reboot button saves the LAN configuration data and reboots the router to make the new configuration effective. Figure 5-7.
5. Advanced Setup NAT You can configure the Virtual Server, Port Triggering, and DMZ Host when NAT is enabled. Virtual Servers A virtual server allows you to direct incoming traffic from the WAN side to a specific IP address on the LAN side. Click on the Add button to add a virtual server. Figure 5-8.
5. Advanced Setup You can select a Service or make new one. Enter the Server IP Address, then click on Save/Apply to submit your configuration. Figure 5-9. Virtual Server Add Screen On this screen you can view and delete servers. Click in the check box under Remove and click on the Remove button to delete selected virtual servers. Figure 5-10.
5. Advanced Setup Port Triggering Click the on the Add button to add Port Triggering for your Internet application. Figure 5-11. Port Triggering Setup Page You can select an application every time or create new one for your application. Then click on Save/Apply to save your settings. Figure 5-12.
5. Advanced Setup On this screen you can view and delete applications. Click in the check box under Remove and click on the Remove button to delete selected applications. Figure 5-13.
5. Advanced Setup DMZ Host You can define the IP address of the DMZ Host on this screen. Enter the IP address and click on Save/Apply. Figure 5-14.
5. Advanced Setup Firewall For security reasons, firewall options can be configured only from the LAN side of the router. IP Filtering – Outgoing The outgoing filter will block the traffic from the LAN side to the WAN side. Click on Add to create filters. Figure 5-15.
5. Advanced Setup Input the filter name, source information (from the LAN side), and Destination information (from the WAN side). Then click on Save/Apply. Figure 5-16. IP Filtering - Outgoing Filter Add Page You can view and delete the outgoing filter settings on this screen. Figure 5-17.
5. Advanced Setup IP Filtering – Incoming Incoming filter filters the traffic from the WAN side to the LAN side. Click on Add to add incoming filter settings. Figure 5-18.
5. Advanced Setup Enter a filter name, information about the source address (from the WAN side), and information about the destination address ( to the LAN side). Select the protocol and WAN interface. Then click on Save/Apply to add the setting. Figure 5-19. IP Filtering - Incoming Filter Add You can view and delete the incoming filter settings from this screen. Figure 5-20.
5. Advanced Setup Firewall – MAC Filtering MAC filtering can forward or block traffic by MAC address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen. Figure 5-21. IP Filtering - MAC Filtering Setup If you click on Change Policy, a confirmation dialog lets you verify your change. Figure 5-22.
5. Advanced Setup If you want to add a setting to the MAC filtering table, enter the Source and Destination MAC address, and select protocol type, frame direction, and WAN interface. Then click on Save/Apply to save it. Figure 5-23. IP Filtering - MAC Filtering Add Page On this screen you can view and delete MAC filtering rules. Figure 5-24.
5. Advanced Setup Parental Control Use the Parental Control feature to restrict the days and times a particular device is allowed to access the Internet. Figure 5-25. Parental Control Screen To set up parental controls: 1. Click on Add. The Time of Day Restriction screen appears. Figure 5-26.
5. Advanced Setup 2. Enter a User Name to identify the target of the restrictions. 3. Enter the MAC address of the network adapter to be restricted, and, optionally, another MAC address. 4. Select the days of the week the restriction is in force. 5. Specify the start and end times the restriction is in force. Use the form hh:mm, where 23:59, for example, is one minute before midnight. 6. Click on Save/Apply.
5. Advanced Setup Click on Add and the Add Network Traffic Class Rule screen appears. Enter and select QoS parameters, then click on Save/Apply. Note that 802.1p Priority and TOS are mutually exclusive. Figure 5-28. Quality of Service Add Screen On this screen you can view and delete QoS settings. Figure 5-29.
5. Advanced Setup Routing – Default Gateway You can change the Default Gateway on the Routing - Default Gateway screen. Figure 5-30.
5. Advanced Setup Routing – Static Route Use the Routing - Static Route screen to add a static route to the routing table. Figure 5-31. Static Route Setup Enter the route information and click on Save/Apply to make it active. No reboot is required. Figure 5-32.
5. Advanced Setup Routing – RIP If RIP is enabled, the router operation can be configured as Active or Passive. Figure 5-33. RIP Setup DNS Server Use the DNS Server screen to request automatic assignment of a DNS or to specify a primary and secondary DNS. Figure 5-34.
5. Advanced Setup Dynamic DNS Use the Dynamic DNS screen to alias a dynamic IP address to a static hostname, allowing your router to be easily accessed from anywhere on the Internet. Figure 5-35. Dynamic DNS To set up a Dynamic DNS entry: 1. Click on Add. The Add Dynamic DNS screen appears. Figure 5-36.
5. Advanced Setup 2. Select a D-DNS Provider from the drop-down list. 3. Enter the Hostname you have selected for the interface. 4. Select the router Interface from the drop-down list. 5. Enter the information you used to register with the dynamic DNS service: for DynDNS, enter your Username and Password; for TOZ, enter your E-mail address and Key. 6. Click on Save/Apply. ADSL There are three major items in the ADSL settings. Figure 5-37.
5. Advanced Setup Phone Line Pair The 6211 ADSL router supports phone lines on pins 2 and 3 or pins 1 and 4 to connect your ADSL line. If your phone system uses pins 2 and 3, attach a normal RJ11 cable to the router and select "Inner pair" on the screen; if your phone system uses pins 1 and 4, attach the phone with the supplied RJ11 cable and select "Outer pair" on the screen.
5. Advanced Setup DSL Advanced Settings Do not change the DSL Advanced Settings unless so directed by your ISP. To view the DSL Advanced Settings screen, click on the Advanced Settings button on the DSL Settings screen (see Figure 5-37). There are five test modes between the router and your ISP: Normal test: Puts the router in a test mode in which it only sends a Normal signal. Reverb test: Puts the router in a test mode in which it only sends a Reverb signal.
5. Advanced Setup Tone Selection To view the ADSL Tone Settings screen, click on the Tone Selection button of the DSL Advanced Settings screen (see Figure 5-38). The frequency band of ADSL is split up into 256 separate tones, each spaced 4.3125 kHz apart. With each tone carrying separate data, the technique operates as if 256 separate modems were running in parallel. The tone range is from 0 to 31 for upstream and from 32 to 255 for downstream. Do not change these settings unless so directed by your ISP.
5. Advanced Setup Port Mapping Use the Port Mapping screen to map multiple ports to a PVC and create bridging groups. Each group will perform as an independent network. Figure 5-40. Port Mapping To create a new mapping group: 1. Click on Add. The Port Mapping Configuration screen appears. Figure 5-41.
5. Advanced Setup 2. Enter a unique Group name. 3. Select interfaces from the available interface list and add them to the grouped interface list using the arrow buttons to create the required mapping of the ports. 4. Click on Save/Apply.
5.
Diagnostics 6 Testing the DSL Connection Your router is capable of testing your DSL connection. The individual tests are listed below. If a test displays a failure status, click on "Test" at the bottom of this page to make sure the failure status is consistent. If the test result continues to show a failure, click on "Help" and follow the troubleshooting procedures. Figure 6-1.
6.
Management 7 Saving and Restoring the Configuration The configuration of your router can be backed up to a file, and also can be restored from a file. You can also restore the router to its factory default configuration. Backing Up Configuration Settings To back up your settings, select Management -> Settings -> Backup Settings. Figure 7-1.
7. Management Verify that you would like to save the file. Figure 7-2. Backup Settings Upload Confirmation Select the location where you want to save the file. Figure 7-3.
7. Management Restoring Configuration Settings To restore saved settings, select Management -> Settings -> Restore User Settings. Figure 7-4. Restore User Settings Screen Select the backup file you want to restore and click on Update Settings. Figure 7-5.
7. Management The router will restore settings and reboot to activate the restored settings. Figure 7-6.
7. Management Restoring Default Settings Restore Default will erase all current settings and restore the router to factory default settings. To restore the router to factory default settings, select Management -> Settings -> Restore Default. Figure 7-7. Restore Default Settings Screen Reply OK to the confirmation dialog. Figure 7-8.
7. Management The router will restore the default settings and reboot. Figure 7-9.
7. Management System Log The System Log dialog allows you to view the System Log and configure the System Log options. Figure 7-10.
7. Management View System Log Click on the "View System Log" button to check the log file. Figure 7-11.
7. Management Configure System Log If the log is enabled, the system will log selected events: Emergency, Alert, Critical, Error, Warning, Notice, Informational, and Debugging. All events above or equal to the selected log level will be logged and displayed. If the selected mode is "Remote" or "Both", events will be sent to the specified IP address and UDP port of a remote system log server. If the selected mode is "Local" or "Both", events will be recorded in the local memory. Figure 7-12.
7. Management SNMP Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in the router. Use the SNMP screen to set up parameters for SNMP access. Figure 7-13. SNMP Screen Select the desired values and click on Save/Apply to configure the SNMP options.
7. Management Internet Time Use the Internet Time screen to specify whether the router uses Simple Network Time Protocol (SNTP) to obtain the time of day from SNTP servers on the Internet. To set up the router to obtain time from an SNTP server: 1. Select “Automatically synchronize with Internet time servers”. The SNTP fields appear. Figure 7-14. Internet Time Screen 2. Select SNTP servers. 3. Specify the time zone offset for your router’s location. 4. Click on Save/Apply.
7. Management Access Control – Services You can enable or disable some services of your router by LAN or WAN. If no WAN connection is defined, only the LAN side can be configured. Figure 7-15. Services Setup If a WAN connection is defined, services of both the LAN side and WAN side can be configured. Figure 7-16.
7. Management Access Control – IP Addresses Web access to the router can be limited when Access Control Mode is enabled. The IP addresses of allowed hosts can be added using Access Control -> IP Address. Figure 7-17.
7. Management First, add the IP address to the IP address list. Figure 7-18. Access Control – IP Address Add Screen Then select "Enabled" to enable Access Control Mode. Figure 7-19.
7. Management Access Control – Passwords Use Access Control -> Passwords to change a password. Select an account and enter the current password and the new password. Then click on Save/Apply. Update Software If your ISP releases new software for this router, follow these steps to perform an upgrade. 1. Obtain an updated software image file from your ISP. 2. Enter the path to the image file location or click on the "Browse" button to locate the image file. 3.
7. Management Reboot Router Select Management -> Reboot Router to reboot the router using the web interface. The router will save the current configuration and reboot itself using the new configuration. The rebooting process takes about two minutes to complete. Figure 7-21. Reboot Router Screen Figure 7-22.
7.
7.
Specifications A Specifications are subject to change without notice. Table A-1. 6211-I1 Specifications 6211-A2-GB21-30 Specification Criteria Environment Operating Temperature: 32° F to 104° F (0° C to 40° C) Storage Temperature: –4° F to 149° F (–20° C to 65° C) Humidity: 5% to 95%, non-condensing Interfaces DSL Line: RJ11 Phone (if present): RJ11 (with integrated phone filter) Ethernet: 10/100BaseT, RJ45 USB 1.1 Power 100 VAC, 50 Hz 110 VAC, 60 Hz 220VAC, 50/60 Hz Protocol Support ANSI T1.
A.
Index A About This Guide, v Access Control IP Addresses, 7-13 Passwords, 7-15 Services, 7-12 ADSL, 5-26 BER Test, 3-7 Line connection, 2-1 Statistics, 3-6 Advanced Settings, DSL, 5-28 Advanced Setup, 5-1 ARP, 3-9 ATM PVC Configuration, 5-2 Statistics, 3-5 B Backing Up Configuration Settings, 7-1 BER Test, 3-7 Bridge Service, 5-4 Bridging groups, 5-30 C Cables Installing, 2-1 Capability, 5-27 CE Marking, B Configuring PC, 2-7 System Log, 7-9 Connecting Hardware, 2-1 Connection Type, 5-3 D Default Gateway
Index Q IP Filtering Incoming, 5-15 Outgoing, 5-13 Quality of Service, 5-4, 5-20 Quick Setup, 4-1 J R Japan Notices, D Rear Panel, 1-4 Reboot Router, 7-16 Restoring Configuration Settings, 7-3 Default Settings, 7-5 Restricting access to Internet, 5-19 RIP, 5-24 Route status, 3-8 Routing Default Gateway, 5-22 RIP, 5-24 Static Route, 5-23 L Line port, 2-1 Local Area Network (LAN) Setup, 5-7 Statistics, 3-3 Logging In, 3-1 M MAC Filtering, 5-17 Management, 7-1 Mapping ports, 5-30 Modulation Methods, 5
Index U W Update Software, 7-15 USB connection, 2-1 driver, 2-4 User Name Default, 2-12 WAN, 3-2, 5-1 Setup, 5-5 Statistics, 3-4 Status, 3-2 Warranty, A Web Interface Home Page, 2-13 Using, 3-1 Weight, A-1 Windows 2000, 2-9 Windows 95, 2-10 Windows 98, 2-10 Windows ME, 2-9 Windows NT, 2-11 Windows XP, 2-7 V View System Log, 7-8 Virtual Servers, 5-8 6211-A2-GB21-30 August 2005 IN-3
Index IN-4 August 2005 6211-A2-GB21-30
