6382 4-Port Router User’s Guide Document No.
Copyright 2005 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Ave. N.
! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered. 3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord. 4.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Supplier's Declaration of Conformity Place of Issue: Paradyne Corporation 8545 126th Avenue North Largo, FL 33773-1502 USA Date of Issue: 2/8/2005 Paradyne Corporation, located at the above address, hereby certifies that the following models: 6382-AX-XXX, 6212-AX-XXX, 6381-AX-XXX, 6210-AX-XXX, and 6211-AX-XXX (where X may be any numeric character) bearing labeling identification number US:AW2DL04B6381A3 complies with: the Federal Communications Commission's ("FCC") Rules and Regulations 47 CFR Part 68, an
Japan Notices This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
Contents About This Guide 1 2 3 Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . v Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Product-Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features of the 6382 4-Port Router . . . . . . . . . . . . . . . . . . . . .
Contents New Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 PPPoE Connection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 PPPoA Connection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Static Connection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 DHCP Connection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Bridged Connection . . .
Contents 4 Troubleshooting The Router Is Not Functional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 You Cannot Connect to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 LEDs Blink in a Sequential Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Status LED Continues to Blink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Status LED is Always Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents iv April 2005 6382-A2-GB20-00
About This Guide Document Purpose and Intended Audience This guide contains detailed information about the 6382 4-port router. It is intended for all users of the router. Document Summary Section Description Chapter 1, Introduction Describes the features of the router. Chapter 2, Hardware Installation and PC Setup Shows how to connect the router and set up your PC to manage the router. Chapter 3, Using the Web Interface Explains how to use the web interface to configure and monitor the router.
About This Guide vi April 2005 6382-A2-GB20-00
Introduction 1 Definitions Before you install or use your new router, you may find it helpful to understand the following terms: A bridge is a device that forwards any message from one part of a network to another. A router is a device that forwards messages according to their network addresses.
1. Introduction Ability to act as a DHCP Server on your network Compatibility with virtually all standard Internet applications Address filtering and DMZ hosting Downloadable flash software upgrades Support for up to eight Permanent Virtual Circuits (PVCs) Support for up to eight PPPoE sessions System Requirements In order to use your modem for Internet access, you must have the following: ADSL service subscription from your ISP.
1. Introduction LED Description (Front Panel) Power LED: On indicates that the power is supplied to the router. Status LED: The Status LED serves two purposes. If the LED is continuously lit, the DSL interface is successfully connected to a device through the LINE port. If the LED is flickering, it is an indication that the router is training (negotiating the connection to its partner modem). Link LED: The Activity LED shows the state of the PPPoA or PPPoE connection.
1.
Hardware Installation and PC Setup 2 Overview This chapter provides basic instructions for connecting the router to a computer or a LAN and to the Internet using DSL. The first part provides instructions to set up the hardware, and the second part describes how to prepare your PC for use with the router. Refer to Chapter 3, Using the Web Interface for router configuration instructions. It is assumed that you have already subscribed to DSL service with your Internet service provider (ISP).
2. Hardware Installation and PC Setup 4. Connect the cylindrical power plug into the POWER connector on the back of the device. Next: — If you have a wall-mount adapter, plug the AC adapter into a wall outlet or a power strip. — If you have a table-top adapter, use the AC power cord to connect the adapter to a wall outlet or power strip. The supplied power adapter may look different than the one illustrated here.
2. Hardware Installation and PC Setup Configuring Your PC’s IP Address Before you start to access the router using the Ethernet connection, you must configure your PC to use DHCP, or change your PC's TCP/IP address to be 192.168.1.x, where x is any number between 2 and 254, with a subnet mask of 255.255.255.0. Your router's default IP address is 192.168.1.1.
2. Hardware Installation and PC Setup 4. Ensure that the check box to the left of the item labeled Internet Protocol (TCP/IP) is checked, and click on Properties. 2-4 Figure 2-2. Network Connections in Windows XP Figure 2-3.
2. Hardware Installation and PC Setup 5. In the Internet Protocol (TCP/IP) Properties dialog box, click in the radio button labeled “Use the following IP address” and type 192.168.1.x (where x is any number between 2 and 254) in the IP Address field. Type 255.255.255.0 in the Subnet Mask field. Figure 2-4. TCP/IP Properties in Windows XP 6. Click on OK twice to confirm your changes, and close the Control Panel. Windows 2000 To configure the IP address under Windows 2000: Procedure 1.
2. Hardware Installation and PC Setup 4. If Internet Protocol (TCP/IP) does not appear as an installed component, click on Install. 5. In the Select Network Component Type dialog box, select Protocol, and then click on Add. 6. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click on OK. You may be prompted to install files from your Windows 2000 installation CD or other media. Follow the instructions to install the files. 7.
2. Hardware Installation and PC Setup 7. Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click on OK. You may be prompted to install files from your Windows ME installation CD or other media. Follow the instructions to install the files. 8. If prompted, click on OK to restart your computer with the new settings. 9. After restarting your PC, double-click on the Network and Dial-up Connections icon in the Control Panel. 10.
2. Hardware Installation and PC Setup 9. Select the network component labeled TCP/IP, and then click on Properties. If you have multiple TCP/IP listings, select the listing associated with your network card or adapter. 10. In the TCP/IP Properties dialog box, click on the IP Address tab. 11. Click in the radio button labeled “Use the following IP address” and type 192.168.1.x (where x is any number between 2 and 254) in the IP Address field. Type 255.255.255.0 in the Subnet Mask field. 12.
Using the Web Interface 3 Logging Into Your Router To configure your router, open your web browser. Ignore any error about lacking a connection. Type the default IP address (192.168.1.1) into the Location field of your browser and press the Enter key. The following screen appears. Figure 3-1. Login Screen The default user name is Admin and the password is Admin. Both are case-sensitive.
3. Using the Web Interface Home Page The first screen (Figure 3-2) that appears after the log in screen is the Home page. From this screen you can configure the LAN and WAN connections, configure the router's security, routing, and filtering, access debugging tools, obtain the status of the router, and view the online help. Figure 3-2. Home Page The basic layout of the Home page consists of a page selection list across the top of the browser window.
3. Using the Web Interface 6382-A2-GB20-00 Figure 3-3. Quick Start - DHCP Figure 3-4.
3. Using the Web Interface Figure 3-5. Quick Start - Static Enter or select Quick Start options as shown in the following table. Table 3-1. Quick Start Options Field Description NAT Click in the check box to activate Network Address Translation (NAT). See Appendix A, Terminology, for a description of NAT. Firewall Click in the check box to activate the firewall. See Appendix A, Terminology, for a description of a firewall.
3. Using the Web Interface Setup To set up LAN and WAN options not available on the Quick Start screens, select Setup from the Home page. Figure 3-6 shows the Setup page. The menu is broken into two sections: the WAN configuration and the LAN configuration. Figure 3-6. Setup Options Wide Area Network Connection The DSL (LINE) connection is the Wide Area Network (WAN) connection. It is also referred to as a broadband connection.
3. Using the Web Interface Configuring the WAN Before the router will pass any data between the LAN interface and the WAN interface, the WAN side of the router must be configured.
3. Using the Web Interface New Connection A new connection is basically a virtual connection. Your router can support up to 8 different virtual connections. If you have multiple different virtual connections, you may need to utilize the static and dynamic routing capabilities of the router to pass data correctly. PPPoE Connection Setup PPPoE is defined in the Internet standard RFC 2516. It is a method of encapsulating PPP packets over Ethernet.
3. Using the Web Interface Idle Timeout - Specifies that PPPoE connection should disconnect if the link has no activity detected for the specified number of seconds. This field is used in conjunction with the On Demand feature. To disable the timeout feature, enter a zero in this field. Authentication – Specifies the authentication protocol: Auto (the protocol is selected by the PPPoE server), PAP (Password Authentication Protocol), or CHAP (Challenge Handshake Authentication Protocol).
3. Using the Web Interface Tools (at the top of the page) and select System Commands. At the System Commands page, click on Save All. PPPoA Connection Setup PPPoA is defined in the Internet standard RFC 2364. It is a method of encapsulating PPP packets over ATM cells which are carried over the DSL line. PPP (Point-to-Point Protocol) is a method of establishing a network session between network hosts. It usually provides a mechanism of authenticating users.
3. Using the Web Interface Password – The password for the PPPoA access. This is provided by your DSL service provider or your ISP. Idle Timeout – Specifies that PPPoA connection should disconnect if the link has no activity detected for the specified number of seconds. This field is used in conjunction with the On Demand feature. To disable the timeout feature, enter a zero in this field.
3. Using the Web Interface To complete the connection you must now click the Apply button. The Apply button will temporarily save this connection. To make the change permanent, click on Tools (at the top of the page) and select System Commands. At the System Commands page, click on Save All. Static Connection Setup A static connection is used whenever a known static IP is assigned. The accompanying information such as the subnet mask and the default gateway should also be specified.
3. Using the Web Interface Figure 3-9. Static IP Connection Setup To complete the connection you must now click the Apply button. The Apply button will temporarily save this connection. To make the change permanent, click on Tools (at the top of the page) and select System Commands. At the System Commands page, click on Save All. DHCP Connection Setup Dynamic Host Configuration Protocol (DHCP) allows the router to automatically obtain the IP address from the server.
3. Using the Web Interface 7. Select the encapsulation type (LLC or VC). If you are not sure which to use, just use the default mode. 8. Select the quality of service (QOS). Leave the default value if your ISP did not provide this information.
3. Using the Web Interface Bridged Connection A pure bridged connection does not assign an IP address to the WAN interface. This connection method makes the router act as a hub that passes packets across the WAN interface to the LAN interface. To configure the router as a bridge: Procedure 1. From the Home page, click on Setup and then click on New Connection. The default PPPoE connection setup is displayed. 2. At the Type field select Bridge.
3. Using the Web Interface To complete the connection you must now click the Apply button. The Apply button will temporarily save this connection. To make the change permanent, click on Tools (at the top of the page) and select System Commands. At the System Commands page, click on Save All. CLIP Connection Classical IP and ARP over ATM (CLIP) allows IP datagrams and ARP (Address Resolution Protocol) requests and replies to be transmitted over ATM using ATM Adaptation Layer 5 (AAL5).
3. Using the Web Interface Figure 3-12. CLIP Connection Setup To complete the connection you must now click the Apply button. The Apply button will temporarily save this connection. To make the change permanent, click on Tools (at the top of the page) and select System Commands. At the System Commands page, click on Save All. Modify an Existing Connection To modify an existing connection: Procedure 1. From the Home screen, click on Setup. 2. Click on the connection you want to modify.
3. Using the Web Interface Modem Setup To configure the DSL modulation type: Procedure 1. From the Home screen, click on Setup. 2. Under WAN Setup, select Modem. This will bring up the Modem Setup screen. Leave the default value if your ISP did not provide this information. For most cases, this screen should not be modified. Figure 3-13. Modem Setup The Apply button will temporarily save these settings. To make the change permanent, click on Tools (at the top of the page) and select System Commands.
3. Using the Web Interface Configuring the LAN To configure LAN parameters, click on Setup on the Home screen. Under LAN Setup, click on LAN Configuration. The LAN Configuration screen appears. Enable/Disable DHCP By default, your CPE has DHCP server (LAN side) disabled. If you already have a DHCP server running on your network, do not enable a second DHCP server. To enable DHCP: Procedure 1. From the Home screen, click on Setup. 2. Under LAN Setup, select LAN Configuration.
3. Using the Web Interface 192.168.1.1 (the default) than the Start IP address must be 192.168.1. 2 or higher. — Specify an End IP address. The End IP Address is the last address the DHCP server can issue. The ending address cannot exceed a subnet limit of 254. The maximum IP address for a router using the default address is 192.168.1.254. If the DHCP server runs out of DHCP addresses, users will not get access to network resources. — Specify a Lease Time.
3. Using the Web Interface Procedure 1. From the Home screen, click on Setup. 2. Under LAN Setup, select LAN Configuration. The LAN Group 1 Configuration screen appears, as shown in Figure 3-14, LAN Group 1 Configuration. 3. Click on “Use the following Static IP Address”. 4. Enter a new IP Address and Netmask. The Apply button will temporarily save these settings. To make the change permanent, click on Tools (at the top of the page) and select System Commands.
3. Using the Web Interface Firewall/NAT Services To enable or disable Firewall and NAT: Procedure 1. From the Home screen, click Setup. 2. Under LAN Setup, select Firewall/NAT Services. By unselecting the Enable Firewall and NAT Services button the firewall and NAT services is disabled for all WAN connections. Enabling Firewall NAT does not automatically apply it to connections. The Apply button will temporarily save this setting.
3. Using the Web Interface Advanced The CPE supports a host of advanced features. For basic router functionality, you do not need to utilize these advanced features. The features help with routing, security, port configuration, and plug and play capability. UPnP UPnP NAT and Firewall Traversal allow traffic to pass through the router for applications using the UPnP protocol. This feature requires one active DSL connection.
3. Using the Web Interface SNTP The SNTP screen lets you specify parameters related to SNTP (Simple Network Time Protocol) servers. To use SNTP: Procedure 1. From the Home screen, click on Advanced and under Advanced, select SNTP. The SNTP screen appears. 2. Enable SNTP and then specify one or more SNTP servers. 3. The Apply button will temporarily save these settings. To make the change permanent, click on Tools and select System Commands. On the System Commands page, click on Save All. Figure 3-18.
3. Using the Web Interface SNMP Use the SNMP (Simple Network Management Protocol) screen to enable and configure the SNMP agent and SNMP trap managers. The SNMP feature generates a trap whenever the IP address of the router changes (except through the Troubleshooting Management Link).
3. Using the Web Interface IP QoS The IP QoS screen lets you establish a particular level of service for each connection you have defined. To set QoS for a connection: Procedure 1. From the Home screen, click on Advanced and under Advanced, select IP QoS. The IP QoS screen appears. 2. Select a connection from the drop-down list and enter or select appropriate options. 3. The Apply button will temporarily save these settings. To make the change permanent, click on Tools and select System Commands.
3. Using the Web Interface To configure a service, game, or other application: Procedure 1. From the Home screen, click on Advanced. 2. Under Advanced, select Port Forwarding. 3. Select the computer hosting the service and add the corresponding firewall rule. 4. If you want to add a custom application, select the User category, click on New, and fill in the port, protocols and description for your application.
3. Using the Web Interface IP Filters Use the IP Filters screen to block all or selected traffic. To set up IP Filters: Procedure 1. From the Home screen, click on Advanced and under Advanced, select IP Filters. The IP Filters screen appears. 2. Select the LAN Group from the drop-down list that these changes will apply to. 3. Select a LAN IP address from the LAN IP drop-down list. Click on New IP to add a new IP address to the list. 4.
3. Using the Web Interface LAN Clients To add a LAN client, or reserve an IP address for a DHCP client: Procedure 1. From the Home screen, click on Advanced. 2. Under Advanced, select LAN Clients. If DHCP is used, all DHCP clients are automatically assigned. If a fixed IP address server is on the LAN and you want this server to be visible via the WAN, you must add its IP address. Once the IP address has been added to you can apply Port Forwarding rules to this IP address. 3.
3. Using the Web Interface The Apply button will temporarily save these settings. To make the change permanent, click on Tools and select System Commands. On the System Commands page, click on Save All. Figure 3-24. VLAN Bridge Filters The bridge filtering mechanism provides a way for the users to define rules to allow or deny frames through the bridge based on source MAC address, destination MAC address and/or frame type.
3. Using the Web Interface be used to delete the entire filter rule. It provides a quick method of selecting all filter rules for deletion. The Enable Bridge Filters button allows you to enable or disable bridge filtering. It can be set or unset during any add, edit, or delete operation. It can also be set or unset independently by pressing the Apply button. Figure 3-25. Bridge Filters Note: The bridge filter table contains three hidden rules.
3. Using the Web Interface Multicast This option enables the IGMP proxy, which allows NAT clients to participate in IGMP multicast groups. It should only be enabled if NAT is also enabled. To enable Multicasting: Procedure 1. From the Home screen, click on Advanced. 2. Under Advanced, select Muliticast. 3. The Apply button will temporarily save these settings. To make the change permanent, click on Tools and select System Commands. On the System Commands page, click on Save All. Figure 3-26.
3. Using the Web Interface IGMP Snooping Use the IGMP Snooping screen to specify whether IGMP Snooping is enabled. When IGMP Snooping is enabled, the router analyzes Internet Group Management Protocol (IGMP) packets to learn multicast group address and port associations. To enable IGMP Snooping: 1. From the Home screen, click on Advanced. 2. Under Advanced, select IGMP Snooping. 3. Click in the check box to enable snooping. The Apply button will temporarily save these settings.
3. Using the Web Interface 3. Specify the New Destination IP. This is the address of the remote LAN network or host to which you want to assign a static route. Enter the IP address of the host for which you wish to create a static route here. For a standard Class C IP domain, the network address is the first three fields of the New Destination IP, while the last field should be 0. The Subnet Mask identifies which portion of an IP address is the network portion, and which portion is the host portion.
3. Using the Web Interface 3. Specify the Protocol. The protocol is dependent upon the entire network. Most networks support RIP v1. If RIP v1 is selected, routing data will be sent in RIP v1 format. If RIP v2 is selected, routing data will be sent in RIP v2 format using subnet broadcasting. If Rip v1 Compatible is selected, routing data will be sent in RIP v2 format using multicasting. 4. Specify the Direction. This determines the direction that RIP routes will be updated.
3. Using the Web Interface Access Control Access control allows certain PCs to access the router after the firewall is enabled. Access control is enabled on a WAN connection only if the firewall is enabled globally (see Firewall/NAT Services on page 3-21) and enabled on that WAN connection. To enable any of the Access Control features: Procedure 1. From the Home screen, click on Advanced. 2. Under Advanced, select Access Control. The Access Control screen appears.
3. Using the Web Interface Tools The Tools tab provides access to system commands and functions. System Commands To make changes permanent, click on Tools (at the top of the page) and select System Commands. The following commands are used to configure the router: Save All: Click on this button in order to permanently save the current configuration of the router. If you do restart the system without saving your configuration, the CPE will revert back to the previously saved configuration.
3. Using the Web Interface Table 3-2 defines the different severity levels. Table 3-2. Severity Levels Severity Level Description Panic System panic or other condition that causes the router to stop functioning. Alert Conditions that require immediate correction, such as a corrupted system database. Citical Potentially critical conditions, such as hard drive errors. Error Error conditions that generally have less serious consequences than errors in the panic, alert, and critical levels.
3. Using the Web Interface Figure 3-32. Remote Log User Management To change your router's username and password: Procedure 1. From the Home screen, under the tools menu, click on User Management. 2. Change the login name and password. 3. If desired, you can change the idle timeout from this screen. The idle timeout determines after how many minutes of inactivity the web interface is logged off. The Apply button will temporarily save these settings.
3. Using the Web Interface Figure 3-33. User Management Update Gateway You can remotely upgrade the router's firmware from the web interface. To upgrade the firmware: Procedure 1. From the Home screen, under the Tools title, click on Update Gateway. 2. Click on Browse, and find the firmware file to download. Make sure this is the correct file. 3. Click on upgrade firmware. Once the upgrade is complete the CPE will reboot. You will need to log back onto the CPE after the firmware upgrade is complete.
3. Using the Web Interface Figure 3-34. Update Gateway Analyzer The Analyzer screen shows link statuses and test results. Figure 3-35.
3. Using the Web Interface Ping Test Once you have your router configured, it is a good idea to make sure you can ping the network. If you have your PC connected to the router via the default DHCP configuration, you should be able to ping the network address 192.168.1.2. If your ISP has provided their server address you can try to ping that address. If the pings for both the WAN and the LAN side are successful, and you have the proper protocols configured, you should be able to access the Internet.
3. Using the Web Interface Modem Test The Modem Test is used to check whether your router is properly connected to the WAN Network by running OAM F4 and F5 end-to-end and segment tests. The test may take a few seconds to complete. To perform the test, select your connection from the list, select a Test Type, and click on the Test button. Before running this test, make sure you have a valid DSL link; if the DSL link is not connected, this test will always fail. Also, the DSLAM must support this feature.
3. Using the Web Interface Status The Status section allows you to view the Status/Statistics of different connections and interfaces: Network Statistics – Select to view the Statistics of the Ethernet and DSL interfaces, as shown in Figure 3-38. Figure 3-38. Network Statistics 6382-A2-GB20-00 Connection Status – Select to view the Status of different connections. DHCP Clients – Select to view the list of DHCP clients.
3. Using the Web Interface Modem Status – Select to view the Status and Statistics of your broadband (DSL) connection, as shown in Figure 3-39. Figure 3-39. Modem Status Product Information – Select to view the router's driver and run-time information, as shown in Figure 3-40. Figure 3-40. Product Information 3-44 System Log – Select to view all logged information.
Troubleshooting 4 The Router Is Not Functional 1. Check to see that the power LED is green and than the network cables are installed correctly. Refer to Connecting the Hardware in Chapter 2, Hardware Installation and PC Setup for more details. 2. Check to see that the LAN and STATUS LEDs are green. 3. Check to see that the STATUS LED is green. POWER STATUS ACTIVITY LAN 1 2 3 4 04-17577 4. Check the settings on your PC. Again, refer to the quick start guide for more details 5.
4. Troubleshooting You Cannot Connect to the Router 1. Check to see that the power LED is green and that the network cables are installed correctly. 2. Make sure that your PC and the router are on the same network segment. The router's default IP address is 192.168.1.1. If you are running a Windows-based PC, type ipconfig /all (or winipcfg /all on Windows 95, 98, or ME) at a command prompt to determine the IP address of your network adapter. Make sure that it is within the same 192.168.1.x subnet.
Terminology A What is a Firewall? A firewall is protection between the Internet and your local network. It acts as the firewall in your car does, protecting the interior of the car from the engine. Your car's firewall has very small opening that allow desired connections from the engine into the cabin (gas pedal connection, etc), but if something happens to your engine, you are protected. The firewall in the router is very similar. Only the connections that you allow are passed through the firewall.
A. Terminology Your machine isn't really directly connected to the Internet, and it really has an internal local network address. When you provide the server's network address to others, you actually provide the address of the router. The router fakes the connection to your machine. You should use the DMZ when you want to run a server that others will access from the Internet. Internal programs and servers (like print servers) should not be connected to the DMZ.
Index A About This Guide, v Access Control, 3-35 ADSL, 1-1 ADSL/R, 1-1 ADSL2+, 1-1 Advanced, 3-22 Advanced Features, 3-22 Analyzer screen, 3-40 Assigning IP Address using DHCP, 2-3 B Back Panel, 1-2 Bridge, 1-1 Connection, 3-14 Filters, 3-29 Bridge Filters, 3-29 Bridged Connection, 3-14 C Cables Installing, 2-1 CE Marking, B Changing IP address, 3-19 CLIP Connection, 3-15 Configuring LAN, 3-18 PC’s IP Address, 2-3 WAN, 3-6 Connecting Hardware, 2-1 CPE update feature, 3-24 D Declaration of Conformity, D
Index J Ports and Buttons (Back Panel), 1-2 Power LED, 1-3 power supply, 2-2 PPPoA Connection Setup, 3-9 PPPoE Connection Setup, 3-7 Support, 1-2 Product-Related Documents, v PVC Support, 1-2 Japan Notices, E L LAN Clients, 3-28 Configuring, 3-18 Connection, 3-5 LED, 1-3 ports, connecting, 2-1 Q LED Blinking in a Sequential Pattern, 4-2 Description, 1-3 Link, 1-3 Status LED continues to blink, 4-2 Link LED, 1-3 Local Area Network Connection, 3-5 Logging In, 3-1 Logging Out, 3-35 QoS, 3-25 Quality of
Index Tests OAM F4 and F5, 3-42 Ping, 3-41 results, 3-40 Tools, 3-36 TOS byte, 3-41 Trademarks, A Traps, 3-24 Troubleshooting, 4-1–4-2 U Update Gateway, 3-39 Upgrade Firmware, 3-39 UPnP, 3-22 User Management, 3-38 Username, 3-1 6382-A2-GB20-00 V VLAN, 3-28 W WAN Configuring, 3-6 Connection, 3-5 Warranty, Sales, Service, and Training Information, A Web Interface, using, 3-1 Wide Area Network Connection, 3-5 Windows 2000, 2-5 95, 98, 2-7 ME, 2-6 NT 4.
Index IN-4 April 2005 6382-A2-GB20-00
