Manual
Table Of Contents
- Contents
- About This Guide
- 1. About the FrameSaver SLV
- 2. User Interface and Basic Operation
- 3. Configuration Procedures
- 4. Configuration Options
- Using the Easy Install Feature
- Using RIP with FrameSaver SLV CSU/DSUs
- Entering System Information and Setting the System Clock
- Setting Up the Modem
- Setting Up Auto-Configuration
- Setting Up Dial Backup
- PVC Backup Over the Network Interface
- Setting Up Back-to-Back Operation
- Configuration Option Tables
- Configuring the Overall System
- Configuring Physical Interfaces
- Assigning Time Slots/Cross Connections
- Configuring Frame Relay for an Interface
- Manually Configuring DLCI Records
- Configuring PVC Connections
- Configuring the IP Path List
- Setting Up Management and Communication Options
- Configuring the Criteria for Automatic Backup
- 5. Configuring the FrameSaver SLV Router
- FrameSaver SLV Router Overview
- IP Routing
- Address Resolution Protocol
- Proxy ARP
- Interface Configuration
- Network Address Translation
- Network Address Port Translation
- Dynamic Host Configuration Protocol Server
- DHCP Relay Agent
- Router Security
- Provisioning the Router Interface
- Configuring the Router Using Terminal Emulation
- 6. Security and Logins
- 7. Operation and Maintenance
- 8. Troubleshooting
- 9. Setting Up OpenLane for FrameSaver Devices and Activating SLM Features
- 10. Setting Up NetScout Manager Plus for FrameSaver Devices
- 11. Setting Up Network Health for FrameSaver Devices
- A. Menu Hierarchy
- B. SNMP MIBs and Traps, and RMON Alarm Defaults
- C. Router CLI Commands, Codes, and Designations
- D. Router Command Line Summaries and Shortcuts
- E. Connectors, Cables, and Pin Assignments
- F. Technical Specifications
- G. Equipment List
- Index
4. Configuration Options
4-100
September 2002 9128-A2-GB20-80
Configuring the Modem Port
Select Modem Port from the Management and Communication menu to configure
the modem port (seeTable 4-25, Modem Port Options).
Main Menu
→
Configuration
→
Management and Communication
→
Modem Port
Link Protocol
Possible Settings: PPP, SLIP
Default Setting: PPP
Specifies the link-layer protocol to be used. Only in effect when the COM port is
configured as a network communication link (Port Use option is set to Net Link).
Display Conditions
– This option only appears when Port Use is set to Net Link.
PPP – Point-to-Point Protocol.
SLIP – Serial-Line Internet Protocol.
Table 4-24. Communication Port Options (5 of 5)
Table 4-25. Modem Port Options (1 of 4)
Port Use
Possible Settings: Terminal, Net Link
Default Setting: Terminal
Assigns a specific use to the modem port.
NOTE: If the Default IP Destination is set to Modem (see Table 4-17, Node IP Options)
and you change Port Use to Terminal, the Default IP Destination is forced to None.
Terminal – The modem port is used for the asynchronous terminal connection.
Net Link – The modem port is a network communications link to the IP network. You
cannot change Port Use to Net Link when the Modem PassThru feature is enabled. When
you try, the
Cannot change Port Use – Modem PassThru is enabled
message
is displayed. See
Modem Operation
in Chapter 7,
Operation and Maintenance
, for more
information about Modem PassThru operation.
Dial-In Access
Possible Settings: Enable, Disable
Default Setting: Enable
Controls whether external devices can dial-in to the system through the internal modem.
This allows dial-in access by a remote terminal when Port Use is set to Terminal. When
Port Use is set to Net Link, Dial-In Access must be set to Enable to allow an external NMS
to dial in to the device.
Enable – Dial-in access is allowed. Incoming calls are answered.
Disable – Dial-in access is not allowed. Incoming calls are not answered. You cannot
disable Dial-In Access when the Modem PassThru feature is enabled. When you try, the
Cannot change Dial-In Access when Modem PassThru is enabled
message
is displayed. See
Modem Operation
in Chapter 7,
Operation and Maintenance,
for more
information about Modem PassThru operation.