Manual
Table Of Contents
- Contents
- About This Guide
- 1. About the FrameSaver SLV
- 2. User Interface and Basic Operation
- 3. Configuration Procedures
- 4. Configuration Options
- Using the Easy Install Feature
- Using RIP with FrameSaver SLV CSU/DSUs
- Entering System Information and Setting the System Clock
- Setting Up the Modem
- Setting Up Auto-Configuration
- Setting Up Dial Backup
- PVC Backup Over the Network Interface
- Setting Up Back-to-Back Operation
- Configuration Option Tables
- Configuring the Overall System
- Configuring Physical Interfaces
- Assigning Time Slots/Cross Connections
- Configuring Frame Relay for an Interface
- Manually Configuring DLCI Records
- Configuring PVC Connections
- Configuring the IP Path List
- Setting Up Management and Communication Options
- Configuring the Criteria for Automatic Backup
- 5. Configuring the FrameSaver SLV Router
- FrameSaver SLV Router Overview
- IP Routing
- Address Resolution Protocol
- Proxy ARP
- Interface Configuration
- Network Address Translation
- Network Address Port Translation
- Dynamic Host Configuration Protocol Server
- DHCP Relay Agent
- Router Security
- Provisioning the Router Interface
- Configuring the Router Using Terminal Emulation
- 6. Security and Logins
- 7. Operation and Maintenance
- 8. Troubleshooting
- 9. Setting Up OpenLane for FrameSaver Devices and Activating SLM Features
- 10. Setting Up NetScout Manager Plus for FrameSaver Devices
- 11. Setting Up Network Health for FrameSaver Devices
- A. Menu Hierarchy
- B. SNMP MIBs and Traps, and RMON Alarm Defaults
- C. Router CLI Commands, Codes, and Designations
- D. Router Command Line Summaries and Shortcuts
- E. Connectors, Cables, and Pin Assignments
- F. Technical Specifications
- G. Equipment List
- Index

7. Operation and Maintenance
7-42
September 2002 9128-A2-GB20-80
Most Recent and Previous Cause Value Messages
The following Cause Value Messages are presented in alphabetical order. The
Cause Number is also provided if you need to convert the message to its
corresponding ITU number for your service provider.
Table 7-14. Most Recent and Previous Cause Value Messages (1 of 6)
Message
Cause
No. What It Indicates What To Do
Bearer Capability
Not Authorized
57 User has requested a
bearer capability that the
user is not authorized to
use.
Arrange for the desired
capability.
Bearer Capability
not Implemented
65 Device sending this cause
does not support the bearer
capability (i.e., channel
type) requested.
Arrange for the desired
capability.
Bearer Capability
Presently Not
Available
58 Bearer capability requested
is supported by the device
generating the cause, but it
is not available at this time.
Arrange for the desired
capability.
Call Awarded and
Being Delivered in
Est Chnl-7
7 An incoming call is being
connected to an already
established channel that is
used for similar calls.
No action is needed.
Call Rejected 21 Equipment sending the
cause does not want to
receive the call at this time.
No action is needed.
Call Terminated by
Remote End
130 Remote DBM rejected or
terminated the call.
1. Retry the call.
2. Verify that the remote
DBM’s link profile is
correct.
Call With Requested
Call ID Has Been
Cleared
86 Network has received a call
resume request, but the call
had been cleared after it
was suspended.
No action is needed.
Channel Type Not
Implemented
66 Device sending this cause
does not support the
requested channel type.
Arrange for the desired
capability.
Channel
Unacceptable
6 Channel identified for the
call is not acceptable to the
receiving device.
Arrange for the desired
capability.
Destination Out of
Order
27 Destination interface
specified is not functioning
correctly so the signalling
message could not be
delivered (e.g., physical or
data-link layer failure at the
remote end, user
equipment is offline).
Verify that the remote
DBM’s link profile is correct.