User's Manual
Table Of Contents
- Contents
- About This Guide
- 1. About the FrameSaver SLV
- 2. User Interface and Basic Operation
- 3. Configuration Procedures
- 4. Configuration Options
- Using the Easy Install Feature
- Using RIP with FrameSaver SLV CSU/DSUs
- Entering System Information and Setting the System Clock
- Setting Up the Modem
- Setting Up Auto-Configuration
- Setting Up Dial Backup
- PVC Backup Over the Network Interface
- Setting Up Back-to-Back Operation
- Configuration Option Tables
- Configuring the Overall System
- Configuring Physical Interfaces
- Assigning Time Slots/Cross Connections
- Configuring Frame Relay for an Interface
- Manually Configuring DLCI Records
- Configuring PVC Connections
- Configuring the IP Path List
- Setting Up Management and Communication Options
- Configuring the Criteria for Automatic Backup
- 5. Configuring the FrameSaver SLV Router
- FrameSaver SLV Router Overview
- IP Routing
- Address Resolution Protocol
- Proxy ARP
- Interface Configuration
- Network Address Translation
- Network Address Port Translation
- Dynamic Host Configuration Protocol Server
- DHCP Relay Agent
- Router Security
- Provisioning the Router Interface
- Configuring the Router Using Terminal Emulation
- 6. Security and Logins
- 7. Operation and Maintenance
- 8. Troubleshooting
- 9. Setting Up OpenLane for FrameSaver Devices and Activating SLM Features
- 10. Setting Up NetScout Manager Plus for FrameSaver Devices
- 11. Setting Up Network Health for FrameSaver Devices
- A. Menu Hierarchy
- B. SNMP MIBs and Traps, and RMON Alarm Defaults
- C. Router CLI Commands, Codes, and Designations
- D. Router Command Line Summaries and Shortcuts
- E. Connectors, Cables, and Pin Assignments
- F. Technical Specifications
- G. Equipment List
- Index
4. Configuration Options
9128-A2-GB20-80 September 2002
4-11
When a Frame Relay Discovery Mode is changed and saved, the
Saving will
cause Auto-Configuration to update and Restart. Are you sure?
prompt appears. N
o is the default for this prompt.
If Yes (y) is entered, the
Delete All DLCIs and PVC Connections?
prompt appears. N
o is the default for this prompt.
— If Yes is entered, all multiplexed DLCIs and PVC Connections are deleted,
except for Management PVCs with the user data port as the primary
destination and the Management PVC that is designated as TS
Management Link.
— If N
o is entered, previously discovered and auto-configured option settings
will not be removed, but configuration updates due to LMI response
messages are performed according to the just saved mode setting.
If No (n) is entered, or if you exit the screen without responding to the prompt,
no Auto-Configuration updates are performed and updates due to LMI
response messages are performed according to the previously saved setting.
Automatically Removing a Circuit
Using the automatic circuit removal feature, which comes enabled, network DLCIs
and PVCs can be automatically removed from the unit’s configuration when the
network service provider no longer supports them. Automatic deletion is based
upon information from a LMI full status response on an active frame relay link.
When this feature is set to:
Enable
– The following will be automatically removed from the unit’s
configuration:
— Unsupported network DLCIs and PVC connections that include
multiplexed network DLCIs.
— Standard network DLCIs that are Payload Managed or IP Enabled.
— Unsupported standard network DLCIs that are not configured as the
primary destination in a management PVC.
— Non-management PVCs in which unsupported standard network DLCIs
are included.
— DLCIs not included in three consecutive LMI full status response
messages.
— LMI status responses that indicate a Deleted status for the DLCI.
All configured options relating to the deleted circuits are also deleted and they
revert to their default settings.
A DLCI will not be deleted if the physical interface or frame relay link is down,
or if the DLCI is used for the TS Management Link.
Disable
– Unused network DLCIs, PVC connections, and management PVCs
must be manually removed.
If the model has ISDN backup capability, ISDN Link Profiles associated with
the deleted records and alternate destinations will be deleted, as well.