Gazebo GZ3584 Aluminum Composite Roof Panels Assembly Instructions 7’ 13’2” 9’11” 12’2” 8’10” Systems Trading Corporation Customer service: (877)782 4482 Email: easygrow@stcaustin.com www.stcny.
Introduction Thank you for purchasing the Gazebo GZ3584. When properly assembled and maintained, this gazebo will provide many years of enjoyment! These instructions include helpful hints and important information needed to safely assemble and properly maintain the gazebo. Please read these instructions completely before you begin. Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of four people. The assembly should take about two hours.
Table of Contents Safety Advice • • • • • • • • • • Introduction.............................................. The gazebo must be positioned and fixed on a flat level surface. Dispose of all plastic bags safely. Keep them out of the reach of children. Keep children and pets away from the assembly area until the work is completed. Always wear shoes, gloves and safety goggles when working. Take special care not to touch overhead power lines with the aluminum profiles.
List of Parts The gazebo is shipped in two cartons. These cartons are heavy. Be careful when lifting them. Wear proper safety gear including work shoes, gloves and goggles. The parts are identified by removable stickers. Place all the parts for each step in staging areas, checking that you have all parts as you go. If any parts are missing or damaged, contact STC customer service before beginning assembly: Customer service: (877)782 4482 No. Part 1 No.
No. Part Aluminum Composite Roof Panel 16 Qty Step 4 black side 7 Aluminum Composite Roof Panel black side 17 2 18 No.
STEP 1 Assembling the Corner Profiles Place all the parts on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. 1.A Components Place corner profiles (1) parallel to each other on the ground. Slide support plates (2) into corner profiles from the end with a single screw hole, as shown.
5 STEP 2 Assembling the Roof Profiles Place all the parts on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Components 2.A Insert end of long roof profile (3) into long roof profile (4) as shown. Fasten with screws (25). Repeat to make two sets.
STEP 3 Attaching Roof Profiles to Corner Profiles 3.A Attach long roof profile sets (3,4) to corner profiles (1) as shown. Fasten with screws (29). Repeat to make two sets. Components 4 Screw (29) x 32 3 3 4 1 29 1 1 3 1 1 29 31 3 3.B 5 Attach short roof profile sets (5,6) to corner profiles (1) as shown. Fasten with screws (29). 1 29 5 4 6 3 3 6 4 5 1 1 1 1 ILLUSTRATION www.stcny.
STEP 4 Attaching the Roof Connectors to Roof and Corner Profiles 4.A Components Attach one roof connector (23) to each corner profile cover (31) and three roof connectors (22) to each roof profile set (3,4) and (5,6) as shown. Fasten with screws (25).
4.B Attach two roof connectors (7) to each each roof profile set (3,4) and (5,6) as shown (facing outwards). Fasten with two screws (25) each. 7 6 3 3 6 7 7 7 4 5 7 4.C 7 5 4 7 25 7 7 Attach four roof corner connectors (36) to gazebo corners on top of profiles (3,4,5,6) as shown. Fasten with two screws (25) each. 36 25 5 4 34 6 36 25 4/6 3 3 6 5 36 4 3/5 IMPORTANT: After this step you should place the gazebo frame in its desired location.
STEP 5 Securing the Gazebo to the Ground 5.A Fasten the gazebo frame to the ground, using three spikes (32) for each support plate. Components Ground spike (32) x 12 1 32 32 2 32 Optional Securing the Gazebo to a Concrete Floor or Wood Deck Concrete Floor: 1. Using an electric concrete drill, drill holes into the concrete floor, corresponding to the holes in the support plates. 2. Insert concrete screws (32) into the holes and hammer into place, using a mallet. 3.
STEP 6 Installing the Roof Gables Components Screw (25) Roof top (9) Roof top end (8) x1 x2 Roof top connector Roof support (12A) (12) x1 Roof top cover (18) x2 Roof gable (11) 1584mm x4 Washer (30) x1 6.A Roof gable (10) 2170mm x6 Hook (37) x4 x 23 Screw (27) x1 x 12 Insert roof top ends (8) into both sides of roof top (9) and fasten with screws (25) from underneath. Attach hook (37) from underneath.
6.B Using at least three people, install the roof gables (10,11,12) in the following order: 4. 10 3. 2. 5. 1. 11 12 11 9 11 10 4. 4. 10 11 11 12 11 2. 5. 1. 3. 10 4. VIEW FROM TOP IMPORTANT: The roof gable profiles (10,11) have pre-drilled screw holes underneath on each end. The end with the shorter distance to the screw hole is connected to the roof top ends (8) and the end with the longer distance to the screw hole is connected to the roof connectors (22,23).
6.C Using screws (25), first connect four roof gable profiles (11) to roof top ends (8) Then use screws (27) to attach their other ends to roof connectors (22) as shown. 8 9 8 11 11 11 22 22 ILLUSTRATION 11 9 11 27 22 11 8 25 www.stcny.
6.E Using at least two people, slide roof gable profiles (10,11) into tunnels of roof top ends (8) and attach with screws (25) from underneath. Then use screws (27) to attach their other ends to roof connectors (22,23) as shown. 8 8 10 10 11 11 10 11 ILLUSTRATION Use screws (25) to attach roof gable profiles (10) to roof connectors (36) from underneath as shown. 8 10 36 27 11 www.stcny.
6.F Attach roof support profiles (12) to roof connector (12A) on roof top (9) and fasten with screws (25) from underneath. Attach their other end to roof connectors (22) using screws (27). 12A 12A 9 12 12 25 27 22 12 6.G Attach roof top cover (18) to roof top ends (8) on roof top (9) and fasten with four screws (25) and washers (30) from the top as shown. 25 30 18 25 30 www.stcny.
STEP 7 Installing the Roof Panels Remove protective plastic from both sides of roof panels. Place side to face toward the sun facing out when installing. Components black side black side Roof panel (17) Roof panel (16) x2 x4 black side Roof panel (15) x4 black side Roof panel (21) Roof panel (20) x2 7.A black side x4 Roof gable cover (13) Roof gable cover (14) x4 black side x6 Screw (28) Roof panel (19) x 10 x4 Slide roof panels (17,21) into their positions as shown.
7.C Slide roof panel set (15,20) into position as shown. Fasten roof panels (15,20) to connectors (7) from below with screws (28). 10 11 12 11 10 20 7 11 11 17 11 10 15 10 21 28 20 VIEW FROM THE TOP 7.D Place roof gable profile (14) on top of roof gable profile (11). Align both profiles. From below the gazebo roof, fix roof gable cover (14) to roof gable profile (11) using screws (26) through pre-drilled screw holes at mid point and end of profile.
7.E Slide roof panel set (16,19) into position as shown. Fasten roof panels (16,19) to connectors (7) from below with screws (28). 7 19 28 VIEW FROM THE TOP 7.F Place roof gable profile (13) on top of roof gable profile (10). Align both profiles. From below the gazebo roof, fix roof gable cover (13) to roof gable profile (10) using screws (26) through pre-drilled screw holes at mid point and end of profile.
7.G Slide upper end of last profile (14) under roof top plate (18) as shown and lower the profile to fit into roof gable profile (11). 18 14 11 ILLUSTRATION From below the gazebo roof, fix roof gable cover (14) to roof gable profile (11) using screws (26) through pre-drilled screw holes at mid point and end of profile. Components 7.H Close each assembly with end covers (24). End Cover (24) x 10 14 24 11 www.stcny.
Enjoy your completed Gazebo! www.stcny.
Gazebo GZ3584 Aluminum Composite Roof Panels Assembly Instructions WARRANTY: Warranty covers damage due to manufacturing defects only. Warranty does not cover weather inflicted damage (Force Majeure) and/or damages caused by not following assembly instructions and adhering to warnings in manual. ATTENTION: Roof profiles, roof panels and gables must be aligned properly during assembly to minimize any possibility of leaking. www.stcny.