A Gazebo GZ3584-1 Aluminum Composite Roof Panels Assembly Instructions %;éw Paragon Group USA Customer Service: (877) 782 4482 @O 2rorgoroioorsompany
introduction Thank you for purchasing the Gazebo GZ3584-1. When properly assembled and maintained, this gazebo will provide many years of enjoyment! These instructions include helpful hints and important information needed fo safely assemble and properly maintain the gazebo. Please read these instructions completely before you begin. Our patented gazebo has been designed for easy assembly. Al steps can be completed by a team of four people.
Safety Advice The gazebo must be positioned and fixed on a flat level surface. Dispose of all plastic bags safely. Keep them out of the reach of children. Keep children and pets away from the assembly area unfit the work is completed. Always wear shoes, gloves and safety goggles when working. Take special care not to touch overhead power lines with the aluminum profiles. Do not attempt to assemble the gazebo in windy or wet conditions. Do not position your gazebo in an area exposed fo excessive wind.
List of Parts The gazebo is shipped in three cartons. These cartons are heavy. Be careful when lifting them. Place all the parts for eac] Wear proper safety gear including work shoes, gloves and goggles. The parts are identified b¥| removable stickers. step in staging areas, checking that you have all parts as you go.
STEP 1 Assembling the Corner Profiles Place all the parts on a level surface Make sure the pieces are in the correct positions before assembling. Carefully follow the larder of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. m ; Components | Place corner profiles {1} parallel! to each other on the ground. Slide support plates (2) info @ comer profiles from the end with a single / screw hole, as shown.
Place all the parts on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Components Insert end of long roof profile (3) into long roof profile (4} as shown. S Fasten with screws (46). Footprint Sect PM"° “ h Repeat to make two chefs.
STEP 3 Attaching Roof Profiles to Corner Profiles Attach long roof profile sets (3,4} to corner profiles (1) as shown. Fasten with screws {47). Repeat to make two sets.
STEP 4 Attaching the Upper Roof Profiles and Roof Connectors {o Roof and Corner Profiles Come era ] SONS TS il | Upper roof pummels (48) Upper roof prime {49} Upper roof prole {50} Upper roof profile (51) Screw{46) U commutator Roof comer Support connector Supp connector Support bar u (9) w Conn-dor m w"mhr 19 (30) 31 (29) Support bar (29) Attach upper roof profiles (48,49,50,51) to roof profiles shown. Overlap profiles in middle of each gazebo side to form one single screw hole.
Attach U connectors (9) fo top of corner posts (1), as shown, using screws (46). m Attach two roof connectors (7) fo each upper roof profile set (48,49) and {50,51) as shown {facing outwards). Fasten with two screws (46) each.
Attach one support connector (30) and one support connector (31) to each corner post (1) at prevailed screw holes, using two screws (46) each. Slide support bars (28) info support connectors (30) and fasten with two screws (46). Attach upper end of support bars (28) o roof profiles fasten with two screws (46). Slide support bars (29) info support connectors (31) and fasten with two screws (46). Attach upper end of support bars (29) to roof profiles fasten with two screws (46).
STEP 5 Securing the Gazebo to the Ground Fasten the gazebo frame 1o the ground, using three spikes (39} for each support plate. Components ~— Ground spike {39) x12 Optional Securing the Gazebo to a Concrete Floor or Wood Deck Concrete Floor: 1.Using an electric concrete drill, drill holes info the concrete floor, corresponding to the holes in the support plates. 2.Insert concrete screws (40) lino the holes and hammer into place, using a mallet. 3. Fasten concrete screws with washers and nuts.
STEP & Installing the Low Roof Gable Profiles ATTENTION: DO NOT ATTEMPT TO ASSEMBLE THIS ALONE | Components Roof Gable Roof Gable Roof Gable Roof Gable Roof Top Te enter U-shaped Cflflnwfinrflum(fl) Cover(21) townsmen 2’0) Connectors) Screws) T-needlework A(43) Screw(46) Scarecrow) Scarecrow) Nut M5(35) Using at least three people, install the roof gables (11,12,13,14) in the following order ATTENTION: Roof Profiles,roof panes 3.
Using screws {32) and nuts {35}, connect roof gable profiles {11} to roof connectors (9) on top of corner profiles {1). Using screws (46, connect roof gable profile (11) to roof top connector beam (22) as shown. Install roof gable profiles (12). < Using screws (45) nuts (35) connect fop center connector {20) fo fop connector beam (22). Using screws (32) nuts (35) connect profiles (12) to inner roof connector (8) on long roof profiles chefs (3,4} and the other end to roof top center connector (20).
Connect the roof top cover {21} to the roof top connector beam {22} as shown. First connect the two U-shaped connectors (23] fo the roof top cover (21}, using four screws {46). Then attach Unshaped connectors (23] fo roof top connector beam { 22) from below, using four screws (33}. Attach T-connectors (43) to underside of roof gable profiles (12}, using screws (46) as shown. Attach X-connectors (44) to underside of roof gable profiles (11, using screws (46} as shown.
STEP 8 Installing the Roof Panels and Upper Roof Profiles IMPORTANT: Pertly cut on the edge of the panels on both side with knife and remove protective plastic of roof panels. Place with black surface toward the sun facing out when installing. [Components ) Mu ‘ g NHH Aluminum Composite Aluminum Composite Aluminum Composite Aluminum Composite Aluminum Composite Roof Panel(ls) Roof Paneling) Roof Panel(17} Roof Panel(18} Roof Panel{19) Screw(34) Fit roof panel (15} on top of roof profiles {12 and 13).
Fit roof panel {16) on fop of roof profiles {12 and 14) as shown and fasten with one screw {34) outer roof connector (7). IMPORTANT: Make sure tho the roof panels are installed exactly in the rider shown, otherwise it will be difficult Io place the top roof gable profiles.
Place roof profile {12A) on top of roof profile (12) as shown and fasten with screws [32) from below (inside gazebo). Fit roof panel (18) on fop of roof profiles {11,14) as shown Fit roof panel {18) on top of roof profiles {11,14)} i as shown and soften with one screw {34) outer roof connector (7).
Place roof profile (14A) on top of roof profile (14} as shown. Align both profiles. Fasten with two screws (32) from below {inside gazebo). Fit roof panel (19) on top of roof profiles (13,14) and fasten with one screws (34) outer roof connector (7). Place profiles [11A) on top of roof profile {11) ; fasten ONLY THE TOP END with 1 screw (32). Fit roof panel (17) on top profiles (11,13) , fasten with one screw (34) outer roof connector (7}, and then fasten (1 1A} with screw (32).
Continue in a clock-wise direction as shown. Place the roof panel {17,18) on top of profiles (11,13,14) , fasten with screw (34) from below.
Place the roof gable profile {13A} on top of (13}, fasten with screw (32§from below of 13. STEP 2 installing the Plastic Caps Components Plastic Cap #1 (37) Plastic Cap #2 (38) x10 x4 Close off roof profiles (12,13,14) with plastic caps #1 {37} and roof profiles {11} with plastic caps #2 (38).
SR ) Gazebo Aluminum Composite Roof Panels Assembly Instructions Enjoy our completed Gazebo! /\ WARNING: Cancer and Reproductive Harmwww.P65Warnings.ca.gov. /\ ADVERTISEMENT: Cancer et Troubles de I’ apparel reproducteurwww.P65Warnings.ca.gov. /\ INADVERTENCE: Cancer y Dario Reproductivowww.P65Warnings.ca.gov. WARRANTY: Warranty covers damage due to manufacturing defects only for a period of 5 years on the structure, and 5 years on the Aluminum Shell from date of purchase.