P 2 R YESTE OL Gazebo GZ584E Assembly Instructions 11’ 9’1 1’’ 9’ ’ 10’ 7’1” max. 9’2” ’ ’ 9’ 10 2’’ Paragon Group USA Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.
Introduction Thank you for purchasing the Gazebo GZ584E. When properly assembled and maintained, this gazebo will provide many years of enjoyment! These instructions include helpful hints and important information needed to safely assemble and properly maintain the gazebo. Please read these instructions completely before you begin. Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of two people. The assembly should take about two hours.
Safety Advice Table of Contents • The gazebo must be positioned and fixed on a flat level surface. • Dispose of all plastic bags safely. Keep them out of the reach of children. • Keep children and pets away from the assembly area until the work is completed. • Always wear shoes, gloves and safety goggles when working. • Take special care not to touch overhead power lines with the aluminium profiles. • Do not attempt to assemble the gazebo in windy or wet conditions.
List of Parts The gazebo is shipped in three cartons. These cartons are heavy. Be careful when lifting them. Wear proper safety gear including work shoes, gloves and goggles. The parts are identified by removable stickers. Place all the parts for each step in staging areas, checking that you have all parts as you go. If any parts are missing or damaged, contact customer service before beginning assembly: Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.com Profile No.
Profile No. 18 Qty Step Profile No. Qty Step 1 8 25 12 7 1 8 26 1 20 8 8 28 4 4 21 32 1,2 4,5 29 4 4 Fabric canopy top 19 Fabric canopy Screw 1/4’’x55mm Screw 1/4’’x15mm We included some extra screws and bolts for your convenience.
STEP 1 Assembling the Corner Profiles Place all the parts on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. 1.A Components Place corner profiles (1) parallel to each other on the ground. Slide support plates (14) into corner profiles from the end with a single screw hole, as shown.
STEP 2 Assembling the Roof Profiles Place all the parts on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Components 2.A Insert end of long roof profile (2) into long roof profile (3) as shown. Fasten with screws (21). Repeat to make two sets.
STEP 3 Attaching Roof Profiles to Corner Profiles 3.A Attach long roof profile sets (2,3) to corner profiles (1) as shown. Fasten with bolts (22). Repeat to make two sets. Components 2 Screw (22) x 32 3 3 2 1 22 1 1 1 22 1 22 2 3.B 5 Attach short roof profile sets (4,5) to corner profiles (1) as shown. Fasten with bolts (22).
STEP 4 Attaching the Roof Connectors to Roof and Corner Profiles 4.A Attach roof connectors (16) to corner profile covers (15) with bolts(21) fasten as shown. Attach roof connectors(16) and (28) to roof profiles(2) and (4) with bolts(29) fasten as shown.
STEP 5 Attaching the Corner Roof Gables IMPORTANT: The roof gable profiles (6) have small protrusions (spring buttons) on their underside. The end with the protrusions is connected to the top gable connector (13). The roof gable extension (11) has a small protrusion underneath which will snap into one of the holes in roof gable extension (9) while stretching the canopy.
5.B Connect one roof gable profiles assembly (6,12) and one roof gable profiles assembly (6,11) opposite each other to top gable connector (13) until the small protrusion on their undersides snap into the holes on the underside of top gable connector (13). 13 6 ATTENTION: The tunnels of top gable connector (13) are marked, in order to avoid mistakes when inserting the roof gable profiles. 6 6 6 13 11 12 5.
5.D Using at least two people, slide the other two roof gable assemblies (6,12 - 6,11) into tunnels of top gable connector (13) until the small protrusion on their undersides snap into the holes on the underside of top gable connector (13). 13 11 6 6 12 6 23 11 ATTENTION: The tunnels of top gable connector (13) are marked, in order to avoid mistakes when inserting the roof gable profiles.
5.E Connect the two roof gable profiles (6,12) and (6,11,9) to roof connectors (16) on opposite corner profiles (1). Fasten with screws (23) as shown. 9 12 11 11/12 6 23 13 6 16 6 6 11 12 9 5.F Slide roof gable extension (9) over roof gable extension (11) until the small protrusion on it’s underside snaps into the third hole on the underside of roof gable extension (9). 28.3” 12 11 24.4” 9 11 1 2 3 4 11.4” 9 28.
STEP 6 Attaching the Center Roof Gables IMPORTANT: The roof gable profiles (7,8) have small protrusions (spring buttons) underneath. The end with the protrusions is connected to the top gable connector (13). Insert ends with push buttons of roof gable profiles (7) on short side of the gazebo into marked tunnels of top roof connector (13) as shown, until they snap into place. Components Roof gable profile(7) Roof gable profile(8) x2 x2 Repeat with roof gable profiles (8) on long side of the gazebo.
STEP 8 Placing the Canopy WARNING!! : When inserting the roof profiles into the fabric pockets of the canopy, you MUST use both hands holding the large piece of roof fabric in order to stretch it. Don’t try to stretch it and pull it just by pulling the pockets! It will tear the pockets as Sunbrella fabric is not elastic by nature. 8.A Place the upper fabric canopy (18) carefully over the higher part of roof gable profiles (6), stretch and slide profiles into fabric pockets.
8.C Using at least two people, place the large canopy (19) carefully over the small canopy (18) and three roof gable profiles (6+12) as shown. Stretch the canopy and slide profiles into fabric pockets in large canopy rim (19). Use TWO hands to pull the fabric backward until the roof profiles slide firmly into the pockets. 18 11 9 19 8 Do NOT try to stretch and pull the roof fabric by pulling the pocket only. This will tear the pocket, as Sunbrella fabric is not elastic by nature.
Optional Securing the Gazebo to a Concrete Floor or Wood Deck Concrete Floor: 1. Using an electric concrete drill, drill holes into the concrete floor, corresponding to the holes in the support plates. 2. Insert concrete bolts (25) into the holes and hammer into place, using a mallet. 3. Fasten concrete bolts with washers and nuts. 1. 2. Components Concrete bolts, washers and nuts (25) x 12 3. Wood Deck: 1.
P 2 Gazebo GZ584E Assembly Instructions WARRANTY: Warranty covers damage due to manufacturing defects only. Warranty does not cover weather inflicted damage (Force Majeure) and/or damages caused by not following assembly instructions and adhering to warnings in manual. WARNING : In order to prevent possible damage to fabric and/ or structure, fabric roof should be removed before wind storms, or major inclement weather events.
