BRIC FA 3 11’x11’ Pergola Assembly Instructions ” ’6 11 0cm 35 7’9” 235cm 11 35 ’6” 0c m 10 32 ’6” 0c m Paragon Group USA Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.
Introduction Thank you for purchasing the 11’x11’ Pergola. When properly assembled and maintained, this pergola will provide many years of enjoyment! These instructions include helpful hints and important information needed to safely assemble and properly main tain the pergola. Please read these instructions completely before you begin. Our patented pergola has been designed for easy assembly. All steps can be completed by a team of three people. The assembly should take about two hours.
Table of Contents Safety Advice Introduction................................................. 2 Table of Contents......................................... 3 List of Parts.................................................. 4 Step 1 Assembling the Corner Posts.................... 6 Step 2 Attaching the Beams to the Corner Posts.... 8 Step 3 Building the Basic Frame ...........................10 Step 4 Securing the Pergola to the ground...........12 Step 5 Installing the Roof Beams.........................
three contact customer service before beginning assembly: Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.
No. Part Qty Step No. Part Qty Step 17 1 6 26 14 3 18 7 6 26A 7 5 19 7 6 27 1 20 2 6 28 16 4 We included some extra screws and bolts for your convenience.
STEP 1 Assembling the Corner Posts Place all the parts on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Components Corner Roof connector (10) (1) x4 1.A x4 Support plate (8) Support frame (9) x4 Screw (23) x4 x 24 Place corner (1) parallel to each other the ground.
1.B Slide support frames (9) over lower end of corner (1). Align pre-drilled screw holes incorner (1) with screw holes in support plate (8). (1) as shown, using two screws (23) for each plate.
STEP 2 Attaching the Beams to the Corner Posts Components Components Screw (23) Short Beam (5) x 28 x2 Long Beam (4) Beam connector (11) x2 x2 2.A Post Connector (15) x4 Magnet (16) Screw (22) x2 Insert beam connector (11) into hollow ends of one long beam (4) and one short beam (5) as shown. Attach with four screws (23) on side. x8 5 11 5 4 4 2.B 23 Attach magnet (16) to side of long beam (4) as shown. Attach with two screws (23).
2.C Place one long beam (4,5) into cut-out on corner posts (1,10) as shown. Attach post connector (15) using two screws (22) through pre-drilled holes in long beam (4,5). Attach post connector to post using four screws (23). Do not tighten the screws, you will tighten them in STEP 3. 1 15 5 1 4 15 1 5 5 1 15 15 Repeat step 2C to create two sets.
STEP 3 Building the Basic Frame IMPORTANT:You need at least 3 people to complete this step! Components Short Beam with track (7) Long Beam with track (6) Beam connector (12) x2 x2 x2 Screw (23) Canopy loops (26) x 16 x 14 3.A 23 Insert beam connectors (12) into long beams with track (6) as shown and fasten using two screws (23) each. 12 12 6 6 Insert long beams with track (6) through post connectors (15) on top of posts, align screw holes and fasten using two screws (23) each.
3.C Using at least 3 people, lift frame sets and slide beam connectors (12) on long beams with track (6) into short beams with track (7) as shown. 7 12 6 7 12 6 Making sure to support the frame properly, fasten using screws (23). 4 7 5 6 6 7 5 23 4 7 6 IMPORTANT:After this step you should place the pergola frame in its desired location. Make sure all corners are squared at 90 degrees.
STEP 4 Securing the Pergola to the Ground Fasten the pergola frame to the ground, using four spikes (21) for each support plate. Lower support frames (9) to cover support plates (8). Components 1 9 1 Ground spike (21) x 16 21 8 8 Optional Securing the Pergola to a Concrete Floor or Wood Deck Concrete Floor: 1. Using a concrete drill, drill holes into the concrete corresponding to the holes in support plates (8). 2. Insert concrete bolts into the holes and hammer into place, using a mallet. 3.
STEP 5 Installing the Roof Beams ATTENTION: DO NOT ATTEMPT TO ASSEMBLE THIS ALONE ! Components Short Beam with track (7A) Long Beam with track (6A) Beam connector (12) x1 x1 x1 Long Beam (2) Short Beam (3) x4 x4 Canopy loops (26A) Beam connector (11) x4 x 26 Screw (22) Roof connector (13) x 16 x2 5.A 23 Insert beam connector (12) into long beam with track (6A) as shown and fasten using two screws (23).
5.B Insert beam connector (11) into beams (2) and (3) as shown and fasten using four screws (23). 2 11 3 2 3 Create four sets. 3 2 5.C 23 Attach beam with track (6A,7A) to roof beams (4,5) using roof connector (13) and fasten with three screws (23) on each side. Make sure to install the beam (6A,7A) exactly as shown.
5.D Attach beams (2,3) to roof beams (4,5) using two long screws (22) on each side.
STEP 6 Installing the Canopy Components Canopy Rod (18) x7 Screw (24) Canopy (17) Canopy Cover (20) x1 Canopy Rod (19) x2 x7 6.A x 14 Metal Cover Connector (14) x4 Screw (25) x 15 Insert canopy rods (19) into canopy rods (20) as shown and fasten with screws (25). Create 7 sets. 18 19 18 19 25 6.B Spread out the canopy (17) on an even Insert one canopy rod (18/19) into the opening. surface.
6.C With the help of two people, pass the canopy rod (18/19) through the canopy loop (26A) in beam with track (6A/7A) as shown. Continue sliding the rod through the canopy sleeve until it emerges at the other end. 17 18/19 17 26A 6A/7A 18/19 6.D Fasten the canopy rod (18/19) at each end to canopy loops (26) in beams with track (6/7) using screws (24). Repeat steps 6C/6D with all seven canopy rods (18/19). Use the attached handles to open and close the canopy.
6.E Slide metal cover connectors (14) into “sleeves “in canopy covers (20). Fasten canopy covers (20) to the roof beams (6/7) with using screws (25) as shown.
Enjoy your completed Pergola ! 19 of 20
BRIC FA 3 11’x11’ Pergola Assembly Instructions WARRANTY: Warranty covers damage due to manufacturing defects only. Warranty damage (Force Majeure) and/or does not cover weather damages caused by not following assembly instructions and adhering to warnings in manual. Paragon Group USA Customer Service:(877) 782 4482 Email:cs-outdoors@paragongroupusa.