Corporation Switch User Manual
Table Of Contents
- Ethernet Networking
- Command Descriptions
- NTCONNNetwork Connect
- NTIDNetwork Sharing Unit ID for Peer-to-Peer Communication
- NTIONetwork I/O (OPTO22) Configuration
- NTIPNetwork IP Address
- NTMPRBNetwork Map Binary Variables for Reading from PLC
- NTMPWBNetwork Map Binary Variables for Writing to PLC
- NTMPRINetwork Map Integer Variables for Reading from PLC
- NTMPWINetwork Map Integer Variables for Writing to PLC
- NTPOLLNetwork Polling Rate
- NTRATENetwork Sharing Rate for Peer-to-Peer Communication
- [ NTS ]Network Status
- NTSELPNetwork Program Select Enable
- NTWRITNetwork Write ASCII String to DVT Camera
- TNTSTransfer Network Status
- TNTSFTransfer Network Status (full-text report)
- VARSHIShared Input Variable for Peer-to-Peer Data Exchange
- VARSHOShared Output Variable for Peer-to-Peer Data Exchange
- [ \ANI ]Network Analog Input Voltage Status
- \ANONetwork Analog Output
- [ \ANO ]Network Analog Output Status
- [ \IN ]Network Digital Input Status
- \OUTNetwork Digital Output
- [ \OUT ]Network Digital Output Status
- \TANITransfer Network Analog Input Status
- \TANOTransfer Network Analog Output Status
- \TINTransfer Network Digital Input Status
- \TIOTransfer Ethernet I/O status
- \TOUTTransfer Network Digital Output Status
N
o
r
t
h
A
m
e
r
i
ca
a
nd
A
s
i
a
:
Compumotor Division of Parker Hannifin
5500 Business Park Drive
Rohnert Park, CA 94928
Telephone: (800) 358-9070 or (707) 584-7558
Fax: (707) 584-3793
FaxBack: (800) 936-6939 or (707) 586-8586
e-mail: tech_help@cmotor.com
Internet: http://www.compumotor.com
E
u
r
op
e
(non-German speaking)
:
Parker Digiplan
21 Balena Close
Poole, Dorset
England BH17 7DX
Telephone: +44 (0)1202 69 9000
Fax: +44 (0)1202 69 5750
G
e
r
m
a
n
y
,
A
u
s
t
r
i
a
, S
wi
t
z
e
r
l
a
nd
:
HAUSER Elektronik GmbH
Postfach: 77607-1720
Robert-Bosch-Str. 22
D-77656 Offenburg
Telephone: +49 (0)781 509-0
Fax: +49 (0)781 509-176
T
ec
hni
ca
l
A
ss
i
s
t
a
n
ce
Contact your local automation technology center (ATC) or distributor,
o
r
...
A
u
t
o
m
a
t
ion
E
-
mail
:
T
ech
_
H
elp
@
cmotor
.
com
T
ech nical
S
upport
6K and Gem6K Series products and the information in this user guide are the proprietary property of Parker Hannifin Corporation or its
licensers, and may not be copied, disclosed, or used for any purpose not expressly authorized by the owner thereof.
Since Parker Hannifin constantly strives to improve all of its products, we reserve the right to change this user guide and software and
hardware mentioned therein at any time without notice.
In no event will the provider of the equipment be liable for any incidental, consequential, or special damages of any kind or nature
whatsoever, including but not limited to lost profits arising from or in any way connected with the use of the equipment or this user guide.
©
2002
, P
a
r
ke
r
H
a
nni
f
in
C
o
r
po
r
a
t
ion
A
ll
R
igh
t
s
R
ese
r
ve
d
U
se
r
I
n
f
o
r
m
a
t
ion
W
ARN
I
N
G
6K and Gem6K Series products are used to control electrical and
mechanical components of motion control systems. You should test your
motion system for safety under all potential conditions. Failure to do so
can result in damage to equipment and/or serious injury to personnel.
!!
Motion Planner and Servo Tuner are trademarks of Parker Hannifin Corporation.
Microsoft and MS-DOS are registered trademarks, and Windows, Visual Basic, and Visual C++ are trademarks of Microsoft Corporation.