CHLG50WN Operating and Installation Instructions
n CHLG50WN c iot Introduction t This gas appliance has been designed and manufactured to all the necessary British Standards. The appliance complies with European Council Directive 90/396/EEC. It also carries the C.E. mark. It is important that you understand how to use and care for the appliance properly before you use it for the first time. We have written this booklet with your safety in mind. Read the booklet thoroughly before you use the appliance.
Contents Contents CHLG50WN Page Lighting the appliance 4 The grill 6 The hotplate 8 The oven 11 Oven cooking chart 14 Slow cooking 18 Care and cleaning 20 Installing the appliance 25 General information 27 What is wrong and why? 28 Servicing 29 Installation Instructions 31 Technical data 32 Safety requirements/ventilation 33 Location of appliance/installation 34 Testing 36 3
Lighting the appliance CHLG50WN Lighting the appliance The ignition system works by means of a battery. Details on how to replace the battery are given on page 27. Grill and hotplate To light 1 Push in the control knob and turn to the large flame symbol (highest setting), and press the ignition button immediately. When the burner has lit release the button. Warning: If the ignition button is not pressed immediately a build up of gas may cause the flame to spread.
To turn off any burner 1 Push in the control knob and turn it to the off position. This is shown by a large dot. For your safety When you are lighting any burner check that it has lit before you leave the appliance. When you are turning off a burner, do not leave the appliance until the flame has gone out.
The grill CHLG50WN The grill The grill is a high-speed grill. The instructions below tell you how to vary the heat setting and how to change the height of the grid to suit the food you are cooking. You should remember to turn the food regularly. You should not use the grill to keep food warm as it will continue to cook the food. Prior to using the grill We suggest that you operate the grill for approximately 5 - 10 mins to burn off any residue from the surface.
Cooking positions Place the grill pan so that the bottom of the handle fits into the hole on the shelf. Most food should be cooked on the grid in the grill pan. The grid can be turned over to suit different thicknesses of food. You can place some dishes straight on to the grill shelf. This is useful when you are browning the top of food such as cauliflower cheese. Preheating You don't usually need to preheat the grill.
The hotplate CHLG50WN The hotplate Heat control The hotplate control knobs turn anticlockwise from 'OFF' to 'HIGH' and then to 'LOW'. You can adjust the heat by turning the control between the highest and lowest settings. These are shown as a large and a small flame symbol. Burner sizes The hotplate has three burner sizes to suit different types of cooking: Largest burner (Rapid) - use a large pan for food such as chips. Medium burners (Normal) - use for everyday cooking.
For your safety 1 Take care to avoid burns and scalds when you are reaching across the hotplate. 2 Use pans with flat bases. They are more stable than pans which are warped. 3 Do not use pans with very heavy handles which cause the pan to tip. 4 Put pans on the centre of the burners. 5 Position pan handles so they cannot be accidentally knocked. 6 Take extra care when you are deep fat frying. Do not cover the pan with a lid. Do not leave a pan unattended.
The hotplate CHLG50WN Helpful hints 1 Keep flames under the base of pans. If the flames lick round the sides of the pans you are wasting gas. 2 Only heat the amount of liquid you need. Do not overfill pans. 3 Cover pans with a lid whenever possible. The food will heat up more quickly and there will be less steam in the kitchen. 4 Try cooking more than one vegetable in the same pan, for example potatoes and carrots. 5 Cut vegetables into smaller pieces. This way they will cook more quickly.
The oven Before you use the oven you should wipe it out with a damp cloth to remove any dust. Heat zones There are zones of heat within the oven. The temperature in the middle is the gas mark you have chosen. The top of the oven is slightly hotter and the lower shelf slightly cooler. The base of the oven is quite a lot cooler. You can make use of these heat zones when you are cooking foods requiring different temperatures all at the same time.
The oven CHLG50WN Baking trays and dishes For your safety Never place cooking dishes, trays and so on over the oven burner. This will damage the appliance as well as the ovenware and possibly the floor covering underneath the appliance. Leave a gap of 13mm (½") between all dishes and the sides of the oven so the heat can circulate properly. Do not push dishes too far back as food will burn if it overhangs the burner flames.
Condensation Condensation may form on the appliance. This is quite normal and nothing to worry about. The condensation forms when heat and moisture are present, for example during cooking. Whenever possible try to make sure that food which contains a lot of moisture for example casseroles are covered. If you do notice any condensation, wipe it up straight away.
5 5 5 Beef Lamb Pork and Veal Roasting meat: 4 4 4 Shelf position Medium: Well Done: Medium: Well Done: Rare: Medium: Well Done: Approximate cooking time 30 mins. per ½kg (1 lb) and 30 mins. 35 mins. per ½kg (1 lb) and 35 mins. 25 mins. per ½kg (1 lb) and 25 mins. 30 mins. per ½kg (1 lb) and 30 mins. 20 mins. per ½kg (1 lb) and 30 mins. 25 mins. per ½kg (1 lb) and 25 mins. 30 mins. per ½kg (1 lb) and 30 mins. Thoroughly thaw frozen joints before cooking them.
Cook as above but calculate weight including stuffing Stuffed poultry 20 mins. per ½ kg (1 lb) and 20 mins. 25 mins. per ½ kg (1 lb) and 25 mins. 15 mins. per ½ kg (1 lb) and 15 mins. 25 mins. per ½ kg (1 lb) 4 4 4 or 5 4 5 4 4 5 Chicken Turkey below 4.5kg (10lbs) over 4.
Plate tart (shortcrust) Fruit pie (shortcrust) Mince pies (flan pastry) 6 6 5 1 1 1&3 Shelf Position 25-35 mins. 25-35 mins. 15-25 mins. Approximate cooking time To help pastry brown on the underside cook on a metal plate, or if plates are flat and have no rim underneath, place on baking tray to cook.
Bread 0.45kg (1lb loaves) 0.90kg (2lb loaves) Rolls and buns Yeast Mixtures: 3 3 2 3 3 3 30-40 mins. 30-40 mins. 10-20 mins. 2 hrs. 45-60 mins. 50-60 mins. Oven cooking chart * When baking bread cook at Gas Mark 8 for 10 minutes before reducing to Gas Mark 6 for the remainder of the cook time. Note: You must soak dried beans then boil them in an open pan for 15 minutes before you add them to any dish.
Slow cooking CHLG50WN Slow cooking The slow cook setting gives a very low heat in the oven. It is particularly useful when you are cooking soups, stews and casseroles because the long slow cooking will make cheaper, tougher cuts of meat more tender. You need to cook food at gas mark 6 for 30 minutes before you turn the oven down to the slow cook setting. This makes sure that the temperature of the food gets hot enough to start the food cooking.
Soups, casseroles and stews l l l l Do not cook casseroles over 2.7 kg (6lb). Bring to the boil on the hotplate then cook on slow cook. Cook in the middle of the oven or above. Cover food with a tight fitting lid or tin foil. Vegetables l l l l l Cut into small pieces. Dried beans must be pre-soaked then boiled in an open pan for 15 minutes before adding to any dish. Place vegetables under meat in casseroles. Cover food with a tight fitting lid or tin foil.
Care and cleaning CHLG50WN Care and cleaning For your safety For hygiene and safety reasons you must keep this gas appliance clean. A build up of fat or other foodstuff could cause a fire. Try to mop up spills and splashes as soon as they happen. But be careful as parts of the appliance will be hot. Do not use any polishes, caustic cleaners, abrasives, washing soda or soap powder except those recommended in this booklet.
You can wash the removable parts in very hot soapy water. You may use mild abrasives. Make sure that the electrode and the hole and slots in the crown are not blocked with food or cleaning materials. Clean the burner crowns by soaking them in very hot soapy water. You can remove any stubborn stains by scouring with a soap filled pad such as 'Brillo'. If you look after the burner crowns in this way they will stay reasonably clean. However the surface will dull with time.
Care and cleaning CHLG50WN The oven The inside of the oven is finished in vitreous enamel. You should clean the oven regularly using hot soapy water and mild abrasives or a soap filled pad such as 'Brillo'. If you use any oven cleaners they must have the Vitreous Enamel Development Council (VEDC) seal of approval. Follow the instructions on the cleaning agent and protect the oven burner with aluminium foil to prevent it becoming blocked. Do not overfill dishes or they will boil over.
Cleaning between the outer and inner Door Glass You can remove the glass from the oven door if you need to. To remove the outer glass 1 Open the oven door so you can get at the two cross head screws on the top of the oven door. 2 Loosen these two screws using a pozidrive screwdriver. 3 You should hold the door glass securely in place with one hand, whilst removing the screws completely, with the other hand. If you do not do this, the door glass could fall forward.
Care and cleaning CHLG50WN .Cleaning The Door Glass To prevent damaging or weakening the door glass panels avoid the use of the following: Household detergents and bleaches Impregnated pads unsuitable for non-stick saucepans Brillo/Ajax pads or steel wool pads Chemical oven pads or aerosols Rust removers Bath/Sink stain removers If the door glass panel becomes chipped or has deep scratches the glass will be weakened and must be replaced to prevent the possibility of the panel shattering.
Installing the appliance For your safety This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation & Use) regulations current editions and the IEE Wiring Regulations. It is important that the appliance is suitable for your gas supply. Your installer should check the rating plate. Make sure that a stability bracket is fitted.
Installation CHLG50WN Positioning The diagram shows how close to the appliance cupboards, shelves, curtains and so on can be fitted. Refer to the diagram and carefully read the instructions to make sure your appliance is fitted safely. If you are in doubt your installer will give you advice. Do not fit any materials which may catch fire for example wood or curtains behind the appliance. Base units which are higher than the hotplate must be 100mm away.
General information For your safety Do not block any of the appliance vents. Never line any part of the appliance with foil. Do not let items which can catch fire or electric mains leads such as kettle flexes trail over any part of the appliance. Moving your appliance You may damage some soft or badly fitted floor coverings when you move the appliance. The floor covering under the appliance should be securely fixed so it does not ruck up when you move the appliance across it.
What is wrong and why? CHLG50WN What is wrong and why? We strongly recommend that you carry out the following checks on your appliance before calling your local Service Force Centre. Problem The oven, grill or hotplate will not light. Check l l l If you cannot hear any sparking or the sparking is slow when you press the ignition button it may not be strong enough to light the appliance. You will probably need to replace the battery. For instructions on how to do this see page 27.
g CHLG50WN Service and spare parts vr ci ni In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning:- 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
Servicing CHLG50WN For your safety Maintenance must only be carried out by a competent /qualified person. Do not try to repair or alter/modify the cooker yourself as this could be dangerous. We recommend that your cooker has an annual gas safety check carried out by our approved service organisation.
INSTALLATION INSTRUCTIONS Serial number inside the storage compartment. Rating Plate on top rear of panel. Please note that the handle may differ in type and shape from that shown in the diagram. For your safety Where Applicable Natural Gas and L.P. Gas versions of this appliance are available. Check that this model is suitable for the type of supply available.
TECHNICAL DATA DIMENSIONS Overall Height to hotplate Height 1462mm (nominal) Width 498mm Depth 600mm (from elbow to front of door panel) 907mm nominal see important note 'Location of the Appliance' (see Page 34). Space for fixing at hotplate level 2mm minimum clearance Space for fixing above hotplate level 100mm each side of appliance Minimum space above grill 500mm Minimum distance from rear wall 20mm Weight of appliance 59.
HOTPLATE Heat Input Injector Marking Natural Gas R.H.F. 1.0kW (3412 Btu/h) 079 R.H.R. 2.0kW (6824 Btu/h) 104 L.H.R. 2.0kW (6824 Btu/h) 104 L.H.F 2.8kW (9554 Btu/h) 130 L. P. Gas Heat Input Injector Marking OVEN Heat Input Injector Marking Thermostat By-pass Marking R.H.F. 1.0kW (71.8g/h) 51 R.H.R. 2.0kW (143.7 g/h) 72 L.H.R. 2.0kW (143.7 g/h) 72 Natural Gas 2.4kW (8189 Btu/h) 108 69 L P. Gas 2.4kW (172.4g/h) 78 78 H.T. Spark 3-4mm H.T. Spark 3-4mm L.H.F. 2.
LOCATION OF APPLIANCE This appliance must not be installed in a bed-sitting room of volume less than 20m³ or in a bathroom, shower room or garage. It is essential that the appliance is positioned as stated below. The appliance must be a minimum of 20mm from the rear wall (note that this dimension is provided by the inlet elbow). Shelves, wall cabinets and cooker hoods must not be fitted closer than 500mm to the top of the grill canopy or within 100mm of the sides of the grill.
3. LEVELLING THE APPLIANCE Adjustable levelling feet at the front and rear are provided on the base of the appliance. Adjustment to suit floor conditions is obtained by rotating in or out the hexagonal feet from the underside of the appliance. A spirit level should be placed on one of the oven shelves to confirm that the appliance is correctly levelled. 4. FITTING THE STABILITY BRACKET It is recommended that if the appliance is to be installed with a flexible supply pipe a stability bracket (SK.4729.
5. CONNECTING TO GAS This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less than R³/8 (³/8" B.S.P.). Connection is made to the Rc½ (½" B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. Check for gas soundness after connecting the gas supply. The gas bayonet connector must be fitted in the shaded area indicated in Fig. 4.
8. CHECKING THE GRILL Fit the grill pan shelf to the splashplate canopy (4 screws). Place the grill pan containing the grid on to the grill pan shelf. Light the grill burner by turning the tap to its' full on position and pressing the ignition button. As soon as the burner is lit the button can be released. If the ignition of the grill fails ensure the grill H.T. wire is fitted to the generator (see Section 2). 9.
NOTES C H L G 5 0 W N - 311575301 38
Contents Check List Note: If you require replacements of the item listed below please contact your local Service Force Centre quoting the relevant part number. The loose contents of this pack include:No.
IMPORTANT NOTICE In line with our continuing policy of research and development, we reserve the right to alter models and specifications without prior notice. This instruction booklet is accurate at the date of printing, but will be superseded if specification or appearance are changed. Description Burner Cap - Rapid Burner Cap - Normal Burner Cap - Simmer Burner Crown - Rapid - N.G. Burner Crown - Rapid - L.P.G. Burner Crown - Normal Burner Crown - Simmer Pan Support No.
