CSG 427 Operating and Installation Instructions
CSG 427 iot n Introduction or This gas appliance has been designed and manufactured to all the necessary British Standards. This appliance carries the C.E. mark. It is important that you understand how to use and care for the appliance properly before you use it for the first time. We have written this booklet with your safety in mind. Read the booklet thoroughly before you use the appliance. Keep the booklet in a safe place so that anyone who uses the appliance can read it.
Contents Page Lighting the appliance 4 The grill 7 The hotplate 10 The ovens 13 Oven cooking chart - main oven 16 - second oven 19 Slow cooking 22 Care and cleaning 24 Installing the appliance 30 General information 32 What is wrong and why? 34 Servicing 35 Installation instructions 37 Technical Data 38 Safety requirements/ventilation 39 Location of appliance/installation 40 Testing 42 3 Contents CSG 427
Lighting the appliance CSG 427 Lighting the appliance The system works by means of a battery. Details on how to replace the battery are given on page 32. For your safety In the event of the burner flames being accidentally extinguished, turn off the burner control and do not attempt to re-ignite the burner for at least 1 min. Hotplate To light: 1 Lift up the lid. You cannot use the hotplate when the lid is down.
Grill To light: 1 Open the door. 2 Push in the control knob and turn it to the right to the large flame symbol (highest setting), and press the ignition button immediately. When the burner has lit release the button. 3 Leave the grill door open when you are using the grill. Warning: If the ignition button is not pressed immediately a build up of gas may cause the flame to spread from the grill cavity. For your safety Never cover the grill pan or grid with foil as this can lead to grill fires.
Lighting the appliance CSG 427 Main oven To light: 1 Open the oven door. 2 Push in the control knob and turn it to gas mark 9, and press the ignition button immediately. When the burner has lit release the button. There will only be small flames at first. 3 Now turn the control knob to the gas mark you want. 4 Wait until the burner is showing large flames. 5 Close the oven door. To turn off any burner 1 Push in the control knob and turn it to the off position. This is shown by a large dot.
The grill The grill is a high-speed grill. The instructions below tell you how to vary the heat setting and how to change the height of the grid to suit the food you are cooking. You should remember to turn the food regularly. You should not use the grill to keep food warm as it will continue to cook the food. Prior to using the grill We suggest that you operate the grill for approximately 5 - 10 mins to burn off any residue from the surface.
The grill CSG 427 Cooking positions There is only one position for the grill shelf (Position 2). Positions are counted from the top downwards. Most food should be cooked on the grid in the grill pan. You can turn the grid over to suit different thicknesses of food. You can place some dishes straight on to the grill shelf. This is useful when you are browning the top of food such as cauliflower cheese. General The shelf in the grill/second oven is different from the shelves in the main oven.
The grill pan and handle The grill pan is supplied with a removable handle. To attach the handle, place the wirework under the cut out in the pan so that the metal plate hooks over the top of the grill pan. Slide the handle to the left and over the central bump on the grill pan. Ensure the handle is correctly located. It is not necessary to remove the grill pan handle during grilling. Place the grill pan on the shelf so that the pan is positioned centrally beneath the grill.
The hotplate CSG 427 The hotplate You can only use the hotplate when the lid is open. If you have any trouble lighting a hotplate burner, turn all hotplate control knobs off and make sure that the burner parts have been replaced correctly. Now light the burner in the usual way. See page 25 for more detailed information. Heat control The hotplate control knobs turn anticlockwise from 'OFF' to 'HIGH' and then to 'LOW'. You can adjust the heat by turning the control between the highest and lowest settings.
For your safety 1 Take care to avoid burns and scalds when you are reaching across the hotplate. 2 Use pans with flat bases. They are more stable than pans which are warped. 3 Do not use pans with very heavy handles which cause the pan to tip. 4 Put pans on the centre of the burners. 5 Position pan handles so they cannot be accidentally knocked. 6 Take extra care when you are deep fat frying. Do not cover the pan with a lid. Do not leave a pan unattended.
The hotplate CSG 427 Helpful hints 1 Keep flames under the base of pans. If the flames lick round the sides of the pans you are wasting gas. 2 Only heat the amount of liquid you need. Do not overfill pans. 3 Cover pans with a lid whenever possible. The food will heat up more quickly and there will be less steam in the kitchen. 4 Try cooking more than one vegetable in the same pan, for example potatoes and carrots. 5 Cut vegetables into smaller pieces. This way they will cook more quickly.
The ovens Before you use the oven you should wipe it out with a damp cloth to remove any dust. Heat zones Main Oven - There are zones of heat within the oven. The temperature in the middle is the gas mark you have chosen. The top of the oven is slightly hotter and the lower shelf slightly cooler. The base of the oven is quite a lot cooler. You can make use of these heat zones when you are cooking foods requiring different temperatures all at the same time.
The ovens CSG 427 The shelf in the grill/second oven is different from the shelves in the main oven. Only use the shelf with the solid metal plate underneath it in the grill/second oven. The plate may glow red when you are using the oven. This will not affect the cooking performance. Most second oven cooking should be carried out using the shelf provided in shelf position 2.
Roasting For best results we recommend open roasting using minimal fat or oil to prevent splashing. It is not necessary to cover meat or poultry or wrap food in foil when roasting as this restricts the circulation of heat and will lead to extended cooktimes. If you are using a roasting bag or cover chicken breast with foil, be prepared to allow an extra 10 - 15 minutes for each 1/2kg (1lb).
5 5 5 Beef Lamb Pork and Veal Roasting meat: 4 4 4 Shelf position Medium: Well Done: Medium: Well Done: Rare: Medium: Well Done: Approximate cooking time 30 mins. per ½kg (1 lb) and 30 mins. 35 mins. per ½kg (1 lb) and 35 mins. 25 mins. per ½kg (1 lb) and 25 mins. 30 mins. per ½kg (1 lb) and 30 mins. 20 mins. per ½kg (1 lb) and 30 mins. 25 mins. per ½kg (1 lb) and 25 mins. 30 mins. per ½kg (1 lb) and 30 mins.
5 4 20 mins. per ½kg (1 lb) and 20 mins. 4 4 25 mins. per ½kg (1 lb) and 25 mins. 4 4 or 5 15 mins. per ½kg (1 lb) and 15 mins. 5 4 25 mins. per ½kg (1 lb). Cook as above but calculate weight including stuffing. Approximate cooking time Thoroughly thaw frozen joints before cooking them. Chicken Turkey below 4.5kg (10lbs) over 4.
Bread 0.45kg (1lb loaves) 8 * 0.90kg (2lb loaves) 8 * Rolls and buns 8* Yeast mixtures: 18 3 3 2 3 4 4 2 2 2&4 Shelf position 30 - 40 mins. 30 - 40 mins. 10 - 20 mins. 2 hrs. approx. 45 - 60 mins. 50 - 60 mins. 25 - 35 mins. 25 - 35 mins. 15 - 25 mins. Approximate cooking time To help pastry brown on the underside cook on a metal plate, or if plates are flat and have no rim underneath, place on baking tray.
Roasting meat: Food 19 5 5 Lamb Pork and Veal Shelf on base Shelf on base Shelf on base Shelf position Medium: Well Done: Medium: Well Done: Rare: Medium: Well Done: Approximate cooking time Oven cooking chart 30 mins. per ½kg (1 lb) and 30 mins. 35 mins. per ½kg (1 lb) and 35 mins. 25 mins. per ½kg (1 lb) and 25 mins. 30 mins. per ½kg (1 lb) and 30 mins. 20 mins. per ½kg (1 lb) and 30 mins. 25 mins. per ½kg (1 lb) and 25 mins. 30 mins. per ½kg (1 lb) and 30 mins.
Cook as above but calculate weight including stuffing. Stuffed poultry Thoroughly thaw frozen joints before cooking them. 20 mins. per ½kg (1 lb) and 20 mins. 25 mins.
Milk pudding Baked sponge pudding Baked custard Shelf position 2 2 2 Gas mark 2 3 3 2 hrs. approx. 45 - 60 mins. 50 - 60 mins. Approximate cooking time 21 Oven cooking chart Note: You must soak dried beans then boil them in an open pan for 15 minutes before you add them to any dish.
Slow cooking CSG 427 Slow cooking Please note: There is no slow cook on the second oven. The slow cook setting gives a very low heat in the oven. It is particularly useful when you are cooking soups, stews and casseroles because the long slow cooking will make cheaper, tougher cuts of meat more tender. You need to cook food at gas mark 6 for 30 minutes before you turn the oven down to the slow cook setting. This makes sure that the temperature of the food gets hot enough to start the food cooking.
Soups, casseroles and stews l Do not cook casseroles over 2.7 kg (6lb). l Bring to the boil on the hotplate then cook on slow cook. l Cook in the middle of the oven or above. l Cover food with a tight fitting lid or tin foil. Vegetables l Cut into small pieces. l Dried beans must be pre-soaked then boiled in an open pan for 15 minutes before adding to any dish. l Place vegetables under meat in casseroles. l Cover food with a tight fitting lid or tin foil.
Care and cleaning CSG 427 Care and cleaning For your safety For hygiene and safety reasons you must keep this gas appliance clean. A build up of fat or other foodstuff could cause a fire. Try to mop up spills and splashes as soon as they happen. But be careful as parts of the appliance will be hot. Do not use any polishes, caustic cleaners, abrasives, washing soda or soap powder except those recommended in this booklet.
Clean the hotplate top using a mild abrasive such as 'Cif'. Take care not to damage the spark electrodes. If the spark electrodes are damaged the burners will not light. You can remove the pan supports, burner caps and burner crowns to clean them. Again take care not to damage the spark electrodes. If any food spills do occur during cooking you can place the pan on another burner to finish cooking. Then you can remove the dirty parts and clean them before the spill 'burns on'.
Care and cleaning CSG 427 The grill Do not clean the grill burner itself. The burner is designed to be self cleaning. Cleaning the grill may cause the holes in the burner to become blocked preventing it from operating correctly. Please note that due to the nature of stainless steel the grill burner may tarnish through use over a period of time. This is quite normal and is not a fault on the appliance. Clean the area around the grill frequently using hot soapy water.
The Main Oven The top, sides and back of your main oven are coated in a special material which helps to keep itself clean. Follow these simple rules to maintain the appearance of the special finish. Do not overfill dishes or they will boil over. Do not put dishes too high in the oven. If you do they may stick to the oven roof. Cover your roasting tins with foil. This will prevent fat splashing. Use a roasting tin which is just large enough for the meat and potatoes.
Care and cleaning CSG 427 Main Oven Cleaning Cycle You need to follow the cycle to keep the inside of the oven in good condition. The type of cooking you do will affect how often you need to follow the cycle. If you do a lot of roasting and very little other baking you should follow the cleaning cycle once a week. If you do very little roasting you will only need to follow the cleaning cycle every 2-3 weeks. To carry out a cleaning cycle: 1. Remove the oven shelves. 2.
Cleaning between the outer and inner door glass You can remove the glass from the main oven door if you need to. To remove the outer glass 1 Open the oven door so you can get at the two cross head screws on the top of the door. 2 Loosen these screws using a pozidrive screwdriver. 3 You should hold the door glass securely in place with one hand, whilst removing the screws completely, with the other hand. If you do not do this, the door glass could fall forward.
Installation CSG 427 Cleaning The Door Glass To prevent damaging or weakening the door glass panels avoid the use of the following: Household detergents and bleaches Impregnated pads unsuitable for non-stick saucepans Brillo/Ajax pads or steel wool pads Chemical oven pads or aerosols Rust removers Bath/Sink stain removers If the door glass panel becomes chipped or has deep scratches the glass will be weakened and must be replaced to prevent the possibility of the panel shattering.
Positioning The diagram shows how close to the appliance cupboards, shelves, curtains and so on can be fitted. Refer to the diagram and carefully read the instructions to make sure your appliance is fitted safely. If you are in doubt your installer will give you advice. Do not fit any materials which may catch fire for example wood or curtains behind the appliance. Base units which are higher than the hotplate must be 100mm away. If a cooker hood is fitted refer to the cooker hood installation instructions.
General information CSG 427 General information For your safety Do not block any of the appliance vents. Never line any part of the appliance with foil. Do not let items which can catch fire or electric mains leads such as kettle flexes trail over any part of the appliance. Moving your appliance You may damage some soft or badly fitted floor coverings when you move the appliance. The floor covering under the appliance should be securely fixed so it does not ruck up when you move the appliance across it.
For your safety Do not try to disconnect the appliance from the gas supply if the supply pipe does not have a bayonet connection, as described in the installation instruction. If this is the case contact the person who installed the appliance.
What is wrong and why? CSG 427 What is wrong and why? We strongly recommend that you carry out the following checks on your appliance before calling your local Service Force Centre. Problem The oven, grill or hotplate will not light. Check l l l If you cannot hear any sparking or if the sparking is slow when you press the ignition button it may not be strong enough to light the appliance. You will probably need to replace the battery. For instructions on how to do this see page 32.
Service and spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning:- 08705 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
Servicing CSG 427 For your safety Maintenance must only be carried out by a competent /qualified person. Do not try to repair or alter/modify the appliance yourself as this could be dangerous. We recommend that your appliance has an annual gas safety check carried out by our approved service organisation.
INSTALLATION INSTRUCTIONS Serial number at the front Rating Plate on top rear of panel. Please note that the handle and pan supports may differ in type and shape from that shown in the diagram. For your safety Where applicable Natural Gas and L.P. Gas versions of this appliance are available. Check that this model is suitable for the type of supply available.
TECHNICAL DATA DIMENSIONS Height to hotplate Space for fixing at hotplate level Minimum space above hotplate Space for fixing above hotplate level Weight of appliance Minimum distance from rear wall Height 907mm (nominal) Width 500mm (nominal) Depth 603 mm (to front of door panel) 2mm minimum clearance 787mm (If a cooker hood is fitted refer to the cookerhood installation instructions). See important note "Location of Appliance", page 40. 62.0kg. 5mm (spacer given by pressed spacer on vent panel).
MAIN OVEN Heat Input Injector Marking Marking SECOND OVEN Heat Input Injector Marking Dual Control By-pass Natural Gas 2.4kW (8189Btu/h) 108 69 L.P. Gas 2.4kW (172.4 g/h) 78 78 Natural Gas 2.4kW (8189 Btu/h) 108 Fixed Internal L. P. Gas 2.4kW (172.4g/h) 78 Fixed Internal GENERAL Ignition Spark Gap H. T. Spark 3-4mm GAS CATEGORY COUNTRIES OF DESTINATION CAT. I2H CAT.
LOCATION OF APPLIANCE 787 787 This appliance must not be installed in a bed-sitting room of volume less than 20m³ or in a bathroom, shower room or garage. It is essential that the appliance is positioned as stated below (see Fig. 1) i.e. shelves, wall cabinets and cooker hoods must be fitted a minimum of 787mm directly above the top of hotplate and 400mm above the hotplate when fitted in line with the outside of the appliance.
INSTALLATION 1. PARTS REQUIRED The loose hotplate parts and battery are packed in the polystyrene fitment on top of the hotplate. 2. LEVELLING THE APPLIANCE Adjustable levelling feet at the front and at the rear are provided on the base of the appliance. Adjustment to suit floor conditions is obtained by rotating in or out the hexagonal feet from the underside of the appliance. A spirit level should be placed on one of the oven shelves to confirm that the appliance is correctly levelled. 3.
4. CONNECTING TO GAS 650 This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less that R³/8. Connection is made to the Rc ½ (½" B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE: ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED TO RESET VALVE I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Fig.
9. CHECKING LID CUT-OFF DEVICE 1. 2. 3. 4. 5. Lift the lid. Turn on and ignite hotplate burner. Close lid. There should be no gas supply to the hotplate and the burner will go out. Turn off the hotplate tap Lift the lid. The gas supply should now be restored to the hotplate when the tap is turned on. 10. CHECKING THE MAIN OVEN 1. 2. 3. 4. 5. 6. Turn the oven thermostat knob to Mk 9 and press the ignition button. As soon as the burner is alight the button can be released.
NOTES 44
NOTES 45
NOTES CSG 427- 311691400 46
Contents Check List Note: If you require replacements of the item listed below please contact your local Service Force Centre quoting the relevant part number. No.
IMPORTANT NOTICE In line with our continuing policy of research and development, we reserve the right to alter models and specifications without prior notice. This instruction booklet is accurate at the date of printing, but will be superseded if specification or appearance are changed. Description Burner Cap - Rapid Burner Cap - Normal Burner Cap - Simmer Burner Crown - Rapid - N.G. Burner Crown - Rapid - L.P.G. Burner Crown - Normal Burner Crown - Simmer Pan Support No.
