INSTRUCTION BOOK COOKER HOOD MCH 662 cod.
Thank you for buying an Moffat product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Moffat Products, please contact our Customer Care Department. For general enquiries concerning your Moffat appliance or for further information, visit our website at http:\\www.electrolux.co.
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation • Child Safety Any installation work must be undertaken by a qualified electrician or a competent person.
YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing. Cooker Hood Controls M. L.
To Operate Open the visor and select the required functions. The appliance can be installed to recirculate or extract contaminated air. The cooker hood is more effective when used in the extraction mode. Recirculation The hood is supplied specified for use in the recirculation mode with the charcoal filter/s fitted. The contaminated air is cleaned by passing through the filters and then back into the kitchen.
MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Always wear protective gloves when cleaning the hood. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel.
3. Clean the metal inlet grille/s and motor support/ s before replacing the charcoal filter/s. 4. Place the new charcoal filter/s (B) over the motor support/s (A), and while holding the filter securely insert the disk (C) and turn clockwise. This appliance can be a fire hazard if the grease and charcoal filters are not replaced as recommended. Changing the Lamps If a lamp fails to function check that the lamp is securely screwed into the holder.
SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Solution Symptom The cooker hood will not start • Check the hood is connected to the electricity supply. • Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively • The fan speed is set high enough for the task. • The grease filter is clean. • The kitchen is adequately vented to allow the entry of fresh air.
GUARANTEE CONDITIONS STANDARD GUARANTEE CONDITIONS We, Moffat, undertake that if within twelve months of the date of the purchase this Moffat built-in appliance or any part there of is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: • • • • • The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.
INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way.
INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas.
Clearance Height A clearance height of 650mm (25 1/2 ”) is required when installed above a built-in electric hob, or 700mm (27 1/2 ”) when installed above a built-in gas hob. A clearance height of 685mm (27”) is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ”) when installed above a slot-in gas cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm.
Venting The hood is more effective when used in the extraction setting (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 100mm (4 ins) minimum. The ducting used must be manufactured from fire retardant material. When the cooker hood is ducted externally the charcoal filter/s must be removed. To Fit the Ducting 1.
Fitting the Cooker Hood to the Wall 1. Fit the brackets with the round ends facing downwards. 2. Once the brackets are secured, lift the hood squarely to the wall slightly higher than the brackets and lower the cooker hood until it is located onto the two brackets. Ensure that the cooker hood is correctly located before letting go. 3. By loosening the screws in the extension arm the hood can be aligned with the front of the adjoining wall cabinets. 4.
To Refit the Hood with Decor Panel Attached 1. Insert the upper visor guides into the upper track in the front of the casing. 2. Pull down the bottom edge of the visor and insert the lower guides into the track in the bottom of the casing. 3. Push the visor in until an audible click is heard. 4. The visor can now be opened and closed in its normal function.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning: 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. Before calling out an engineer, please ensure you have read the details under the heading Something Not Working. When you contact the Service Force Centre you will need to give the following details: 1.
55 - 77 High Street - Slough BERKSHIRE SL1 1DZ © Electrolux plc 2002
