PLBS 30 SOLDERING IRON WITH HOLDER Operation and Safety Notes 6
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.
1 2 3 4 4 5 5 8 6 7 A C 9 10 11 B 3 D
Table of contents Introduction Proper use ...............................................................................Page Features and equipment.........................................................Page Included items .........................................................................Page Technical information .............................................................Page 7 8 8 8 Safety advice 1. Workplace safety...............................................................Page 2.
Introduction The following pictograms are used in these operating instructions / on the device: Read instruction manual! Observe caution and safety notes! Caution – electric shock! Danger to life! Risk of explosion! Risk of fire! Warning - Hot surfaces! V~ Volt (AC) W Watts (Effective power) Wear a breathing / dust mask, protective glasses, gloves and clothing.
Introduction Do not eat! Do not drink! Dispose packaging and appliance in an environmentally-friendly way! Soldering iron with holder Introduction Please make sure you familiarise yourself fully with the way the device works before you use it for the first time and that you understand how to handle it correctly. Please read the operating instructions below. Be careful to keep these advice notes and if necessary pass them on to a third party.
Introduction Features and equipment 1 2 3 4 5 6 7 8 9 10 11 Soldering pencil Soldering tip Helical spring Clips Third hand Holder for copper attachments Multifunctional holder Soldering sponge Universal attachment Pointed attachment Conical attachment Included items 1 1 1 2 4 1 1 Soldering pencil Multifunctional holder Tin solder, 10 grams Soldering tips (1x installed) Copper attachments (engraving tips) Solder sponge Operating instructions Technical information Electricity supply: 230 V ~ F
Safety advice Safety advice CAUTION! Failure to observe the instructions and advice given below may result in electric shock, fire and/or serious injury. 1. Workplace safety a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents. b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes.
Safety advice c) Use a residual current device (RCD) for protection if operating the electrical power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock. d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device.
Safety advice drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. DANGER OF BURNS! Never touch the hot soldering tip or the molten solder. You could suffer burn injuries. Always let the device cool before you replace components on the device, clean it or check its condition. After use let the soldering pencil cool down in air only.
Safety advice Do not eat, drink or smoke in rooms where soldering is carried out. Otherwise your hands may transfer any adhering traces of lead via food or cigarettes into your body. Always wash your hands immediately after soldering . Do not dispose of soldering waste with the household rubbish. Soldering waste must disposed of as special waste. 4. Careful handling and use of electrical power tools a) When not in use always ensure that electrical power tools are kept out of reach of children.
Safety advice / Before first use Original accessories / attachments Use only the accessories detailed in the operating instructions. The use of attachments or accessories other than those recommended here could lead to you suffering an injury. Before first use Fitting the helical spring Insert the narrower end of the helical spring 3 into the opening of the multifunctional holder 7 .
Operation Operation Switching on and off Switching on: Insert the mains plug into a suitable mains socket. Switching off: Pull the plug out of the mains socket to switch off the device. Third hand CAUTION! DANGER OF BURNS! The clips on the third hand 5 can become hot while you are soldering the workpiece. 1. Fold out the third hand 5 upwards. 2. Rotate the clips 4 until they are oriented in the required direction. 3. Clamp the workpiece between the two clips 4 .
Operation Soldering — The soldering pencil has a rated output of 30 watts and is therefore ideal for electronics soldering. The design of the soldering pencil makes it especially suitable for use where access is difficult or for fine soldering work. To achieve the best results use electronics solder 1.0 (10 g electronics solder with integrated flux is included) or 1.5 mm diameter 100 % Sn. We recommend the use of soldering paste (not soldering grease or soldering fluid) as a flux.
Operation / Maintenance and cleaning You can fashion and decorate various materials with your soldering pencil. Remove the parts of the surface or engrave design elements into it (see Fig. D). You can carry out these decorations in, for example, wood, leather, paper, papier mâché, smooth fabrics, thin plastics or candle wax. Try every application out on surplus material and see if you get the effect you wish to have. This means you will avoid damaging the item you wish to work on. Universal attachment 9 : E.
Service centre / Warranty Service centre WARNING! Have your device repaired only by qualified specialist personnel using original manufacturer parts only. This will ensure that your device remains safe to use. WARNING! If the plug or mains lead needs to be replaced, always have the replacement carried out by the manufacturer or his service centre. This will ensure that your device remains safe to use. Warranty The warranty for this appliance is for 3 years from the date of purchase.
Warranty / Disposal made unter warranty. This applies also to replaced and repaired parts. Any damage and defects extant on purchase must be reported immediately after unpacking the appliance, at the latest, two days after the purchase date. Repairs made after the expiration of the warranty period are subject to payment. GB DES UK LTD Tel.: 0871 5000 700 (£ 0.10 / minute) e-mail: support.uk@kompernass.com IE Kompernass Service Ireland Tel: 1850 930 412 (0,082 EUR/Min.) Standard call rates apply.
Disposal / Declaration of conformity / Producer Contact your local refuse disposal authority for more details of how to dispose of your worn-out devices. Declaration of conformity / Producer We, Kompernaß GmbH, the person responsible for documents: Mr Dennis Dohm, Burgstr.
IAN 46461 KOMPERNASS GMBH Burgstraße 21 D-44867 Bochum © by ORFGEN Marketing Last Information Update: 02 / 2010 Ident.-No.