Installation Guide

Installation & Operating Instructions for the
F4503
Parrotuncle Owner’s Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Parrotuncle Lighting, 218 Black Tie Lane, Chapel Hill, NC www.parrotuncle.com
Parrot Uncle YOU CAN BE SURE OF are trademarks of Eileen Grays LLC. Used under license by Eileen Grays LLC. All rights reserved. Made in China
MAKE THE ELECTRIC CONNECTIONS
AFTER INSTRUCTION
INSTALLING THE LIGHT KIT
WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main
fuse box before wiring.
1. Insert the receiver into the mounting bracket with the flat side of the receiver facing the
ceiling.
2. Motor to Receiver Electrical Connections: Connect the Black wire from the fan to Black
wire from the receiver. Connect the white wire from the fan to the white wire from the
receiver. Connect the blue wire from the fan to the Blue wire from the receiver. Secure wire
connections with the wire nuts provided.
3. Receiver to House suppliy wires Electrical Connections: Connect the black(hot) wire from
the ceiling to the black wire from the receiver. Connect the white(neutral) wire from the
ceiling to the white wire from the Receiver. Secure the wire connections with the wire nuts
provided.
4. Ligt kit to motor wires Electrical Connections: Connect the two white wires from light pan
to the black and blue wires from fan. Secure the wire connections with the wire nuts
provided.
WOBBLE
The fan blades have been adjusted in the factory to minimize any wobble
NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS
VIBRATION. MOVEMENT OF A FEW CENTIMENTERS IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING BRACKET AND DOWNROD ARE SECURE.
BALANCING A WOBBLIGNG CEILING FAN:
For your convenience, a Balancing Kit is included; please follow this procedure when balancing the fan:
1) Install fan without light dome before balancing the fan.
2) Define the base plate into four areas(point A,B,C&D). Use one weight from the balance kit to lightly stick on the edge of the base plate(Point A), if the wobble worsens, then take off the balance kit to lightly stick on the
opposite side(Point B); if the wobble is worse,then go to the adjacent point C or D, if the wobble gets better, then securely stick on the weight at this location on the base plate.
3) After balancing the fan, assemble the light dome to the light base.
NOISE
When it is quiet(especially at night) you may hear occasional small noises. Slight power fluctuations and frequency signals superimposed in the electricity for off-peak hot water control,may cause a change in fan motor
noise. This is normal. Please allow a 24-hour “breaking-in” period, most noises associated with a new fan disappear during the time. The manufacturer’s warranty covers actual faults that may develop and NOT minor
complaints such as hearing the motor run – All electric motors are audible to some extent.
CARE AND CLEANING
1. Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please make sure to turn off electricity power before you maintain your fan
2. Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
3. Motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY CLEANING OR REPAIRS.
1.Remove the 4 garnish nuts preassembled from the garnish screws on the base plate.
Connect two white wires from light kit to the black and blue wires from fan, using wire
nuts provided. Attach the light fixture onto the base plate. Aligning the 4 holes on the light
fixture with the 4 preassembled garnish bolts on the base plate. Reinstall the 4 garnish
nuts that were just removed. And tighten all nuts and screws securely.
2. Install 5 X Max.40 watt bulbs (bulb not included)
WARNING: Over lamping the fan will result in the fan lights shutting down until the proper
wattage of bulbs are installed. Replace bulbs with the correct wattage bulbs, turn the
power on.
WARNING: Do not replace bulb until it cools down.