Installation Guide

Installation & Operating Instructions for the
F4601
Parrotuncle Owner’s Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Parrotuncle Lighting, 218 Black Tie Lane, Chapel Hill, NC www.parrotuncle.com
Parrot Uncle YOU CAN BE SURE OF are trademarks of Eileen Grays LLC. Used under license by Eileen Grays LLC. All rights reserved. Made in China
MAKE THE ELECTRIC CONNECTIONS
AFTER INSTRUCTION
WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring
NOTE: Do not connect the motor supply cable to a dimmer switch.
1. Insert the receiver into the mounting bracket with the flat side of the receiver facing the ceiling.
2. Motor to Receiver Electrical Connections: Connect the Black wire from the fan to Black wire from the receiver. Connect the white
wire from the fan to the white wire from the receiver. Connect the blue wire from the fan to the Blue wire from the receiver. Secure
wire connections with the wire nuts provided.
3. Receiver to House supply wires Electrical Connections: Connect the black(hot) wire from the ceiling to the black wire from the
receiver. Connect the white(neutral) wire from the ceiling to the white wire from the Receiver. Secure the wire connections with the
wire nuts provided.
4. Light kit to motor wires Electrical Connections: Connect the two white wires from light pan to the black and blue wires from fan.
Secure the wire connections with the wire nuts provided. provided.
WOBBLE
The fan blades have been adjusted in the factory to minimize any wobble
NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW
CENTIMENTERS IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING BRACKET AND DOWNROD ARE SECURE.
BALANCING A WOBBLING CEILING FAN:
For your convenience, a Balancing Kit is included; please follow this procedure when balancing the fan:
1) Install fan without light dome before balancing the fan.
2) Define the base plate into four areas(point A,B,C&D). Use one weight from the balance kit to lightly stick on the edge of the base plate(Point A), if the wobble worsens, then take off the balance kit to lightly stick on the opposite side(Point B); if the wobble is
worse,then go to the adjacent point C or D, if the wobble gets better, then securely stick on the weight at this location on the base plate.
3) After balancing the fan, assemble the light dome to the light base.
NOISE
When it is quiet(especially at night) you may hear occasional small noises. Slight power fluctuations and frequency signals superimposed in the electricity for off-peak hot water control,may cause a change in fan motor noise. This is normal. Please allow a
24-hour “breaking-in” period, most noises associated with a new fan disappear during the time. The manufacturer’s warranty covers actual faults that may develop and NOT minor complaints such as hearing the motor run – All electric motors are audible to
some extent.
CARE AND CLEANING
1. Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please make sure to turn off electricity power before you maintain your fan
2. Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
3. Motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY CLEANING OR REPAIRS.
INSTALLING THE DECORATIVE PENDANTS
5 bags of chains with small crystals in 5 different length, marked with A,B,C,D ,E and 61 crystal beads
Please follow the below steps to assemble properly
You should have below contents for assembly:
1. Unpack bag E, take out the chain from the bag (1 pc)
2. Connect the crystal bead to the chain with the clip at
the end of the chain.(refer to the below fig)
3. Hang the assembled crystal prism to the light pan
with hook on the top of the chain as shown in Fig x.
Make sure to hang on the light pan at E point
4. Unpack bag D and take out the chains from the
bag(total 6pcs). Repeat Step 2 and 3. Make sure to hang
on the light pan at 6 points on the circle D as shown in
below Fig
5. Unpack bag C and take out the chains from the
bag(total 12pcs). Repeat Step 2 and 3. Make sure to
hang on the light pan at 12 points on the circle C as
shown in below Fig.
6. Unpack bag B and take out the chains from the
bag(total 18pcs). Repeat Step 2 and 3. Make sure to
hang on the light pan at 18 points on the circle B as
shown in below Fig.
7. Unpack bag A and take out the chains from the
bag(total 23pcs). Repeat Step 2 and 3. Make sure to
hang on the light pan at 23 points on the circle A as
shown in below Fig
8. Double check all connections and make sure all are
secured. You light kit is ready for operation.
NOTE: Make sure to
hang the crystal
prisms in order:
E-D-C-B-A
Safety
Safety
Safety
Safety
Safety