Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
13
F.
Install the Vehicle Detector(s)
Follow the instructions provided with the vehicle detectors for installing the detector loop(s), speakers, and
microphones.
For information on wiring and configuring the vehicle detector(s) to the basestation see see “Basestation to
Component Wiring” on page 20.
For information on installing the vehicle detector circuit boards in the basestation, see “Installing Accessory Boards in
the Basestation” on page 23.
G.
Assemble the
PAR
Drive Thru Headset G5H1
The components that make up a
PAR
Drive Thru Headset G5 are packaged and shipped as individual parts:
PAR
Control Pod, G5 (includes a pack of ID Tags)
PAR
Carrier, G5 (includes a pack of ID Tags) and
PAR
Battery, G5
Use the instructions below to assemble these parts to make a fully functional headset.
Installing ID Tags
In
PAR
drive-thru systems with Reminder and Alert features (in V5 release software) installed, you can (by installing
ID tags on each headset) easily.
•
Assign and identify headsets to crew members
•
Attend to hygiene concerns
Each Control Pod and Carrier shipped has a bag enclosed with 8 different colored tags that can be interchanged by
the staff. The Control Pod and Carrier come pre-installed with Black ID Tags. The colors included in the bag are:
Red, Green, Blue, Yellow, Purple, Black, White, Orange, Pink
Follow the procedure below to install ID Tags:
•
Control Pod
Remove the existing ID Tag from the Control Pod, replace with the color of your choice. Gently apply pres-
sure (using the tip of a ball point pen, for example) so the ID Tag securely holds its position.
•
Carrier
Flip open the Head Pad as shown below.
From the outside, gently push the ID Tag out Replace this Tag with one of your choice from the bag of ID Tags
After removing the ID Tag replace with the color of your choice, gently apply pressure (using the tip of a ball
point pen, for example) so the ID Tag securely holds its position.
Close the Head Pad.
Figure 8.