Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
33
Menu
Available on Lane1
Available on Lane2
- PAGE Messages Can Cross Lanes?
Yes
No
- Order Point TALK With No Vehicle
Yes
No
- “Pull Ahead” Prompt (Tandem ONLY)
No
Yes
- Vehicle Detector #1 Type
Yes
No
- Vehicle Detector #2 Type
No
Yes
- Vehicle Detector #1 Minimum
Yes
No
- Vehicle Detector #2 Minimum
No
Yes
- Auto Un-Mute HS Mic in Hfree Mode
Yes
No
- External Audio-In Routing Mode
Yes
No
- Ext. Audio-In Gate Threshold Level
Yes
No
- Mute External Audio-In When Busy
Yes
No
- Kitchen Noise Reduction
Yes
No
- Haptic Alerts on Headsets
Yes
No
- Blue LED Alerts on Headsets
Yes
No
- 08 Headset Setup
Yes
No
- 09 O.T. Modes Setup
Yes
No
- 10 Site Scheduling
Yes
No
-
11
Site Information
Yes
No
- 12 Digital IO Setup
Yes
No
- 13 Change Passwords
Yes
No
- 14 Installer Setup
Yes
No
- 15 Factory Setup
Yes
No
- 16 Network Settings
Yes
No
- 17 Reboot System
Yes
No
- 18 Revision Levels
Yes
No
Greeter Menu
H.
Change Basic Volume Settings
IMPORTANT NOTE
All volume settings should be adjusted during normal or peak business hours. Adjusting them during slow times
will likely produce volume settings that are too low.
IMPORTANT NOTE
Inbound and outbound are always defined from the perspective of the headset.
Inbound Microphone Volume
Changing the inbound microphone volume affects the sound volume coming from the customer order point
microphone.
To turn up or down the inbound microphone:
•
Enter the configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System Menu
.
•
Select a new value for
01 Drivethru Volume
>
Inbound Mic volume
. The range is 0 (silent) to 20 (max).