Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
9
•
A Dual Drive-Thru (see Figure 4) is comprised of two completely separate drive-thru systems, each with its own
lane, usually on opposite sides of the building, its own order point, and one or two drive-thru windows for
payment and pick up. The simplest dual drive-thru is two single drive-thrus, but it is possible to have dual
tandem, dual side-by-side, or even a combination of different drive-thru types.
Number and Configuration of Basestations
Figure 4.
Only one G5 Basestation Model G5B1 is required to support a Single Lane or Dual Lane operation. Single Lane
basestations do not have the Dual Lane functionality activated. Dual Lane basestations come with Dual Lane
functionality already enabled at factory.
Regardless of the type of Dual Lane, in the event you are attempting to upgrade a previously purchased Single Lane
basestation to operate in Dual Lane, the basestation’s Dual Lane functionality must be activated. To activate this Dual
Lane functionality, you must purchase the
PAR
Drive-Thru System G5 Dual Lane Upgrade Package SKU# 78-6911-
5206-6. See “Appendix: Upgrading a Single Lane Basestation to a Dual Lane” on page 71, on how to upgrade from
a Single to a Dual with the software purchase.
Number and Type of Vehicle Detectors
G5 Basestation Model G5B1 can accommodate up to two vehicle detectors; one for each Lane’s Order Point.
There are two basic types of vehicle detector output signal: presence and pulse.
•
Presence detectors are most common. They tell the base station when a vehicle is present over the detector.
They remain active as long as the vehicle stays within the range of detection.
•
Pulse detectors are less common. They tell the base station when a vehicle has arrived, but have no mecha-
nism to know if or when the vehicle leaves. An air hose is typically used to provide the pulse signal when a
vehicle rolls over it.
D.
Install the Battery Charger
The G5 headset batteries can be charged while the battery is still in the headset using the G5 Headset Charging
Station G5 or separately using a standalone
PAR
Drive-thru Headset Battery Charger, G5 12-slot. All lights and
indications will flash on the battery and not on the chargers.
The XT-1 headset uses the 6-slot or 3-slot battery charger.