Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
10
Installation Instructions G5 Release A
PAR
Drive-thru Headset Battery Charger, G5 12-Slot
The battery charger uses the same power adapter as the basestation.
Perform the following steps to install and use the 12-slot battery charger.
•
Select a placement location, either:
-
A flat, dry surface such as a desktop or shelf.
-
An easy-to-reach wall.
•
The power outlet must be near the equipment and be accessible, and
cord placed where it cannot be pinched or bent.
•
If wall mounting is to be used: Due to the many different wall types
avail-able, hardware is not included. Secure the product to the wall with
(2) anchors suitable for the type of wall, and which can support a
1.3lb/0.6kg minimum load.
•
Place the charger on the surface.
•
Connect the PAR supplied power adapter between the wall receptacle
and the charger.
•
Insert each battery to be charged into a slot on the charger. The LED
lights on the battery will light up indicating the level of charge. Each LED
indicates a charge of 25%. When all LEDS are lit steady green, the battery
is fully charged.
•
When charging is complete, the batteries are ready for use.
Figure 5.
PAR
Drive-Thru Headset Charging Station, G5
Headset Charging Station, G5 uses the same power adapter as the basestation. Perform the following steps to install
and use the Headset Charging Station, G5:
•
Select a placement location, either
•
A flat, dry surface such as a desktop or shelf.
•
An easy-to-reach wall.
•
The power outlet must be near the equipment and be accessible, and cord placed where it cannot be pinched
or bent.
•
If wall mounting is to be used: Due to the many different wall types available, hardware is not included. Secure
the product to the wall with anchors suitable for the type of wall, and which can support a 2.9lb/1.3kg mini-
mum load.
•
Place the charger on the surface.
•
Connect the PAR supplied power adaptor between the wall receptacle and the charger.
•
Insert a G5 Headset (with a G5 battery in it) into the Headset bay on the charger.
•
Alternatively, you may insert the G5 battery to be charged into a slot on battery bay of the charger.
•
The LED lights on the battery will light up indicating the level of charge. Each LED indicates a charge of 25%.
When all LEDS are lit green, the battery is fully charged.