Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
12
Installation Instructions G5 Release A
XT-1 6-Slot or 3-Slot Battery Charger
Perform the following steps to install and use the 6-slot or 3-slot battery charger (see Figure 7).
Figure 7.
•
Select a placement location:
•
A flat, dry surface such as a desktop or shelf.
•
An easy-to-reach wall location if you have the optional wall-mount bracket.
•
The power cord should be in place where it cannot be pinched or bent.
•
Install the wall-mount bracket on the wall, if applicable.
•
Place the charger on the wall-mount bracket or surface.
•
Connect the power supply transformer between the wall receptacle and the charger. The charge indicator
lights will flash.
•
Insert each battery to be charged into a slot on the charger. The charge indicator lights for each slot will light
steadily red to indicate that the battery is charging or green to indicate that the battery is fully charged.
•
When charging is complete, the batteries are ready for use.
IMPORTANT NOTE
A fully discharged (dead) battery can take as long as 3 ½ hours to recharge. Fully charged batteries should be
stored whenever they are not in use. Leaving them on the charger does not harm them or waste energy.
E.
Install the Order Point Speaker and Microphone Assemblies
Use the recommended speaker and microphone systems listed below and follow the included instructions:
•
PAR
Microphone Assembly. Part # 78-6911-4935-1
•
PAR
Speaker Assembly, Duplex, 5 inch. Part # 78-6911-4411-3
•
PAR
Speaker Assembly, Duplex, 4 in 78-6911-5202-5
•
PAR
Microphone Duplex, Foam block assembly 78-6911-5201-7
For information on wiring the speaker and microphone to the base station, see “Basestation to Component Wiring”
on page 20.
IMPORTANT NOTE
Solder and insulate, using heat shrinkable crimp caps, all connections including loop, microphone and speaker.
When using Part
#
78-6911-4935-1 and Part
#
78-6911-4411-3 for Microphone and Speaker, respectively, it is
recommended that the two be acoustically separated by treating the speaker post with the PAR Acoustic Kit.
For more information refer to “Appendix:
PAR
Acoustic Kit Installation Guide” on page 67.