Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
16
Installation Instructions G5 Release A
Removing and Replacing the Cover
To remove the basestation cover:
•
Disconnect power from the basestation.
•
Loosen the two screws located at the bottom of the cover.
•
Lift the cover upward and away. The display and keypad remain with the base, not with the cover.
To replace the basestation cover:
•
Verify there are no obstructions (tools, etc.) in the way of the cover being closed.
•
Align the top edge of the cover with the base.
•
Swing the bottom half of the cover down into place and gently push it against the base until it locks into place.
Tighten the two screws located at the bottom of the cover.
Mount the Station
Perform the following procedure to install the basestation (See Figure 12).
•
Remove the base station cover:
Figure 12.
•
Attach the basestation to the wall using (4) screws and possibly wall anchors.
•
The power outlet must be near the equipment and be accessible, and cord placed where it cannot be pinched
or bent.
•
Due to the many different wall types available, hardware is not included. Secure the product to the wall with
anchors suitable for the wall type, and which can support a 4.0lb/1.8kg minimum load.