Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
1
Table of Contents
1.
Overview ................................................................................................
3
A.
Safety Information .................................................................................................. 3
B.
Other Conventions .................................................................................................. 5
2.
Installation .................................................................................................
7
A.
Overview of Installation ............................................................................................... 7
B.
Required Materials (Not Supplied) .............................................................................. 7
C.
Design the Installation ................................................................................................. 7
D.
Install the Battery Charger ........................................................................................... 9
E.
Install the Order Point Speaker and Microphone Assemblies .................................... 12
F.
Install the Vehicle Detector(s) ..................................................................................... 13
G.
Assemble the
PAR
Drive Thru Headset G5. ............................................................. 13
H.
Install the Basestation .................................................................................................. 15
I.
Connect the Components ........................................................................................... 17
J.
Basestation to Component Wiring ......................................................................... 20
K.
Auxiliary Detector Relays ............................................................................................. 21
L.
Installing Accessory Boards in the Basestation ............................................................23
M.
Power Up ................................................................................................................. 26
3.
Configuration .........................................................................................
28
A.
Enter Configuration Mode ...................................................................................... 28
B.
Navigating the Basestation Display ........................................................................ 28
C.
Finding the MAC Address of the G5 Basestation ......................................................... 30
D.
Configuring with a Computer .................................................................................. 30
E.
Logging into the Base Station with a PC ...................................................................... 31
F.
Switching Between Lane1 and Lane2 .......................................................................... 31
G.
Menu Options for Lane1 and Lane2 ............................................................................. 32
H.
Change Basic Volume Settings ................................................................................ 33
I.
Change Noise Reduction Level ............................................................................... 39
J.
Set System Date and Time ...................................................................................... 39
K.
Change Global Settings ........................................................................................... 39
L.
Haptics “Vibration” Alerts and Blue LED Alerts on Headsets ................................ 42
M.
Order Taking Modes Setup ..................................................................................... 43
N.
Change Site Scheduling ........................................................................................... 43
O.
Change Site Information ......................................................................................... 44
P.
Digital IO Setup ........................................................................................................ 45
Q.
Change Passcodes ................................................................................................... 45
R.
Split and Cross Lane Mode ....................................................................................... 46
S.
Installer Setup ................................................................................................................ 46
T.
Factory Setup (Restore Factory Defaults) .............................................................. 47
U.
Create and Load Templates .................................................................................... 47
V.
Reboot System ........................................................................................................ 47
W.
Check the Revision Levels ........................................................................................48
4.
Troubleshooting .....................................................................................
49