Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
35
IMPORTANT NOTE
To avoid feedback and echo, set the outbound talk volume as low as possible.
To change the outbound talk monitoring settings:
•
Enter the configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System Menu
.
•
Select
02 Monitor Volume
.
•
To enable or disable the monitor playing the outbound talk, change the value for
Outbound Talk: Enable
to
ON
or
OFF
.
•
To change the volume level, select a new value for
Outbound Talk: Volume
. The range is 0 (silent) to 20
(maximum).
Vehicle Present
Changing the vehicle present volume affects how loudly the monitor plays the vehicle present tone. You can also
disable the monitor playing the vehicle present tone.
To change the vehicle present monitoring settings:
•
Enter the configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System Menu
.
•
Select
02 Monitor Volume
.
•
To enable or disable the monitor playing the vehicle present tone, change the value for
Vehicle Present:
Enable
to
ON
or
OFF
.
•
To change the volume level, select a new value for
Vehicle Present: Volume
. The range is 0 (silent) to 20
(maximum).
Vehicle Approach
Some sites are equipped with a vehicle approach detector, which alerts you when a vehicle enters the parking lot or
drive through approach lane. If your site is equipped with the detector, you can change the volume at which the tone
is played on the monitor. Also, if you do not wish to hear the tone, you can disable it.
To change the vehicle approach monitoring settings:
•
Enter the configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System Menu
.
•
Select
02 Monitor Volume
.
•
To enable or disable the monitor from playing the vehicle approach tone, change the value for
Vehicle
Approach: Enable
to
ON
or
OFF
.
•
To change the volume level, select a new value for
Vehicle Approach: Volume
. The range is 0 (silent) to 20
(maximum).
Page Messages
Paging is headset-to-headset communications. Changing the page message volume affects how loudly the monitor
plays internal paging messages. You can also disable the monitor playing internal paging messages.
IMPORTANT NOTE
To avoid feedback and echo, set the volume as low as possible.
To change the page message volume monitoring settings:
•
Enter the user service mode, see “Enter Configuration Mode” on page 28, and choose
1 System Menu
.
•
Select
02 Monitor Volume
.
•
To enable or disable the monitor playing internal paging messages, change the value for
PAGE Messages:
Enable
to
ON
or
OFF
.