Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
36
Installation Instructions G5 Release A
•
To change the volume level, select a new value for
PAGE Messages: Volume
. The range is 0 (silent) to 20
(maximum).
Greeter Messages
Changing the greeter message volume affects how loudly the monitor plays the greeter messages. You can also
disable the monitor playing the greeter messages.
To change the greeter message volume monitoring settings:
•
Enter the configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System Menu
.
•
Select
02 Monitor Volume
.
•
To enable or disable the monitor playing greeter messages, change the value for
Greeter Messages: Enable
to
ON
or
OFF
.
•
To change the volume level, select a new value for
Greeter Messages: Volume
. The range is 0 (silent) to 20
(maximum).
Monitoring Audio Separately for the Two Lanes
The “Lane Monitor Outputs” option only appears when the basestation is operating in a Dual Lane. It has two choices
– “Mixed” or “Separate”.
In Mixed mode, all Monitor audio from both lanes 1 and 2, are played on the single Speaker.
In
Separate
mode, if you have hooked up two separate speakers for the two lanes, then traffic on Lane1 is played on
Speaker1; traffic from lane2 is played on speaker2.
Change the Night Volume
You can assign a standard reduction in the volume level of the customer order point speaker for night hours when
lower volume is typically required. With the night volume set, the system automatically adjusts the volume during night
hours, then back to normal during the day.
To change the night volume setting:
•
Enter the configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System Menu
.
•
Select a new value for
03 Night Volume
>
Reduce DriveThru Volume At Night By
. The range is 0 (No
reduction) to the current day volume level (silent).
IMPORTANT NOTE
Night Volume is never higher than Day Volume.
Night volume reduction is a subtracted value, not the resulting level; therefore, if it is the same as the day
volume level, the speaker will turn off at night.
You cannot change the day outbound talk volume on this screen, only the reduction amount identified above.