Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
37
Registering Headsets
Each headset must be registered to a basestation before it can be used.
XT-1 headsets have a single serial number. This number is imprinted on the headset.
G5 headsets have 2 serial numbers - one for the G5 Control Pod and the other for the G5 Carrier. The G5 Control
Pod serial number is the primary tracking number for the G5 headset and this is the serial number that gets registered
on the basestation. Once registered, it should not need to be registered again unless it is intentionally removed.
Add Headsets
The procedure below applies to both G5 and XT-1 headsets. Each headset has a unique serial number. This number
is broadcast to the basestation whenever the headset signs on.
To register a headset:
•
Enter the base station configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Select
04 Registration
>
1 Add New Headsets
.
•
Power on the headset when prompted.
Or in the case of a G5 headset, insert the battery to automatically power on the headset.
•
Wait up to two minutes for
{Headset xxxxxxx Has Been Registered!}
to appear at the bottom of the display.
•
Repeat the steps above for additional headsets.
•
Press
Mode
when finished.
IMPORTANT NOTE
Alternatively, you may use the Special Short Cut Keys. While on the Run Mode and no fields are selected for
editing, the left, and right buttons act as short cut keys to two frequently accessed configuration screens.
Press the left arrow – Launches the Add New Headsets screen.
Remove Headsets
Perform the following steps to un-register a lost, destroyed, or otherwise removed headset from the system,
including a headset that is sent back to PAR for repair. The headset would have to be registered again at a later date.
•
Enter the base station configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Select
04 Registration
>
2 Remove Headsets
.
•
Scroll to the number of the headset you want to un-register.
•
Press
Enter
.
IMPORTANT NOTE
If you do not know or have access to the number of the headset to be unregistered, identify the headsets that
you want to remain in service and unregister any that remain on the list.
Another method to identify the headset’s serial number without having to disassemble the headset is through the
Basestation’s Headset Setup Menu.
•
Enter the base station configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Select
08 Headset Setup
.
•
Pay attention to the Serial Number displayed to the right of Currently Editing Headset field.
•
Conduct a Page with the operational XT-1 or G5 headset on hand.
•
The Headset Selection field will jump to the headset that is currently paging, which is the headset in your
hand.