Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
41
•
Enter the base station configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Change the value for
07 Global Settings
>
’’Store is Now Closed’’ Prompt?
to
Yes
or
No
.
Pull Ahead Prompt
You can let customers know to pull ahead when they are at order point #2 in a tandem drive-thru when:
•
it is out-of-service.
•
no car is present at order point #1.
Figure 27.
This option is available on Lane2 settings only. Perform the following procedure to enable or disable the automatic
pull ahead for Order Point #2:
•
Enter the base station user service mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Press the
Lane
button.
•
Change the value for
07 Global Settings
>
’’Pull Ahead’’ Prompt (Tandem Only)?
to
Yes
or
No
.
Customer Order Point Prompt Language
Perform the following procedure to select the language(s) of the store closed and pull ahead prompts. The prompts
can be spoken in English, Spanish, French, German, or repeated in multiple languages:
•
Enter the base station configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Change the value for
07 Global Settings > Order Point Prompts in English?
to
Yes
or
No
.
•
Press
Enter
to implement the change or press
Mode
to abandon the change and leave the option at its pre-
vious setting.
•
Change the value for
07 Global Settings
>
Order Point Prompts in Spanish?
to
Yes
or
No
.
•
Press
Enter
to implement the change or press
Mode
to abandon the change and leave the option at its pre-
vious setting.
•
Change the value for
07 Global Settings
>
Order Point Prompts in French?
to
Yes
or
No
.
•
Press
Enter
to implement the change or press
Mode
to abandon the change and leave the option at its pre-
vious setting.
•
Change the value for
07 Global Settings
>
Order Point Prompts in German?
to
Yes
or
No
.
Order
Point #2
Order
Point #1
Cash
Pick Up