Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
43
•
Gently vibrate and/or
•
Flash a Blue LED (at the tip of the mic boom)
when a vehicle is detected at the Order Point. These options are, by default, set to
YES
.
This option only applies to G5 headsets. If you currently have no G5 headsets and only XT-1 headsets, then enabling
or disabling this option will not affect the normal functioning of the XT-1 headset.
Haptics “Vibration” Alerts on Headsets
Perform the following procedure to enable or disable the Haptics “Vibration” Alerts on the Headset upon a vehicle
detect at the Order Point.
•
Enter the base station configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Change the value for
07 Global Settings
>
Vibe Alerts on Headsets
to
YES
or
NO
.
Blue LED Alerts on Headsets
Perform the following procedure to enable or disable the Blue LED Alerts on the Headset upon a vehicle detect at the
Order Point.
•
Enter the base station configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Change the value for
07 Global Settings
>
Blue LED Alerts on Headsets
to
YES
or
NO
.
M.
Order Taking Modes Setup
Perform the following procedure to enable or disable some of the seven different order taking modes from appearing
on the Run Menu:
•
Enter the base station configuration mode, see “Enter Configuration Mode” on page 28, and choose
1 System
Menu
.
•
Navigate to
09 O.T. Modes Setup
.
•
Change the value for each of the following options to
Yes
or
No
:
•
Manual Listen/Push To Talk
•
Manual Listen/Manual Latching Talk
•
Auto Listen/Push To Talk
•
Auto Listen/Manual Latching Talk
•
Hands Free
•
Outside
•
Always On (Bypass Vehicle Detector)
(Press the directional arrows to scroll up and down the list)
IMPORTANT NOTE
Order taking modes are described in the Operation section.
PAR recommends you do not set up more than three order taking modes.
N.
Change Site Scheduling
The site schedule is the calendar of store open and closing times.
IMPORTANT NOTE
All timekeeping is done using a 24 hour clock (e.g., 6:00 p.m. appears as 18:00).