Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
49
4.
Troubleshooting
A.
Headset Indicator Lights
The following table describes the operating modes of the headsets according to the indicator lights. Use it as a
troubleshooting reference.
Table B. G5 Battery Indicator Light Modes
Indicator
Mode Description
Green LEDs
The battery is out of the G5 battery Charger and the button has been pressed and
held down.
Each LED represents 25% charge.
A fully charged battery would have all 4 LEDS lit Green.
From the top (in the diagram on the left) if
4 successive LEDs lit green indicates a charge between 75% and 100%
3 successive LEDs lit green indicates a charge between 50% and 74%
2 LED lit green indicates a charge between 25% and 49%
1
LED lit green indicates a charge between 0% and 24%
One of the LEDs is blinking Green
The battery is in the Charger and is currently charging
From the top:
1st LED flashing Green – Battery currently between 0 and 25% charge
2nd LED flashing Green – Battery currently between 26 and 50% charge
3rd LED flashing Green – Battery currently between 51 and 75% charge
4th LED flashing Green – Battery currently between 76 and 100% charge
Top and Bottom LEDs are Green
Battery End of Life.
Replace the battery
Bottom LED blinking Green
(Battery not in charger)
Charge on the battery has depleted below 5% of its State of Charge.
The battery needs to be charged immediately.
Table C. G5 Headset Indicator Light Modes
Indicator
Mode Description
Off (no light)
Indicates power is off.
Headset is in sleep / hibernate mode. Picking up (or moving) the headset awakens it
and the headset will begin to sign on to the base.
Headset was signed on, and then went to SLEEP (lights off after 5 minutes of inactiv-
ity). When the headset is moved, it wakes up to SOLID GREEN.
Headset was signed on, and then went to SLEEP and then HIBERNATE (total 10
minutes of inactivity). When the headset is moved, it wakes up to Flashing Green
(see below).
Headset battery is completely out of charge or dead.
Solid Green
Headset is signed on, Lane 1, no car present, standby
Solid Red/Green
Headset is signed on, Lane 2, no car present, standby
Solid Red
Headset is in transmitting mode, ie, headset microphone is live. Either Order Taking,
or Page mode.
Flashing Red & Green
Headset has not registered, but found an open base to which it will try to register.
Flashing Green
(immediately after power on)
Headset is registered but has not yet synchronized or signed on to the basestation.
Headset is out of range of basestation.
Flashing Red & Green
Headset is not registered and has not found a base station.
Steadily Flashing Red
Headset is the active order taker, but the outbound talk to the customer is muted.