Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
C.
Installation Guidelines - Single Housing
Microphone and speaker are contained within a single housing. Component installation is the same for both
microphone and the speaker. The microphone and speaker must be separated from each other by foam.
•
Ensure that the inside of the housing is clean and dry.
•
Install the
PAR
Vibration Control Tape to the inside of the top and side walls of
the housing (fig.4).
•
Using a pair of scissors, cut one piece of tape to be approximately 1"
less than the length of the inside of the top wall. The four pieces of tape
used for the side walls can be used as is from the kit and do not require
trimming.
•
Peel and discard the release liner from the back of the tape.
•
Center a piece of tape on the inside of the top of the housing. Locate
the position of the microphone (speaker) and center a piece of tape on
the inner wall of the housing centered with the microphone. Repeat for
the opposite wall. Repeat this step for the speaker.
•
Install the TUFCOTE® TBK Faced Foam to the inside of the housing and over the
vibration control tape (fig. 5).
•
Standard method:
Cut one piece of foam to be positioned between the speaker and
microphone. In order for the foam to fit securely, cut it slightly larger
than the inner dimensions of the housing. It should fit snugly between
the walls of the housing without buckling.
Check the fit of the faced foam to the inside of the housing, in the areas
adjacent to the microphone and the speaker. Cut into individual pieces
to fit the inside of each wall of the housing as shown in the illustration.
•
Alternative method:
Form one piece of insulation into a “u” shape and position it in the upper
pan of the housing.
Form the second piece of insulation into an upside-down “u” shape and
position it in the lower pan of the housing.
•
Peel and discard the release liner from the back of the faced foam.
•
Align the center of the foam with the centerline of the top wall of the
cavity and then work toward the edges until the foam is centered on
the inside of the top and side walls of the cavity.
•
When positioned correctly, press the foam firmly to secure it in place.
•
Install the Thinsulate™ Acoustic Insulation (fig. 6)
•
Loosely line the housing with the acoustic insulation. For the best
appearance, position the black side of the insulation toward the outside
of the housing.
•
If there is excess insulation, overlap it against the inside of the first layer.
61 Installation Instructions G5 Release A