Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
Installation Instructions G5 Release A
64
12.
Appendix: Upgrading a Single Lane Basestation to a Dual Lane
A 7-digit code is necessary in order to upgrade the software on the single lane G5 basestation to enable the dual lane
capabilities. This 7-digit code is unique to each basestation and is based on the MAC IP Address. Once the
PAR
Drive-
Thru System G5 Dual Lane Upgrade Package SKU#78-6911-5206-6 has been purchased, you will need to provide the
following information to PAR in order to receive the upgrade code:
Customer (Store) Name:
Street address: City: State: Zip:
Basestation Serial #:
MAC Address:
- - - - -
To find the MAC address of the G5 Basestation, enter the configuration mode and choose
1
System. Then select 16 Network Setup. You will see 6
pairs of alpha-numeric characters enclosed in square brackets following the words MAC ADDRESS. Please put those 12 alpha-numeric characters
in the boxes above in the order as shown on the basestation menu screen.
PAR Invoice
#
used to purchase the Upgrade Software: PZ
PAR Invoice Date:
Once you have completed the information above, please call PAR at 800-328-0033 and select Option 1, option 3.
Or you can email this information to tacsupport@mmm.com.
After you receive the 7-digit code from PAR, go to the G5 Basestation Main Menu Screen:
Figure 30.
From the Main Menu Screen:
1.
Enter the 7-digit code you received from PAR on the keypad.
2.
Press <MODE> key and the base station display will indicate it has been upgraded.
3.
Enter the installer pass code 12345 on the keypad and press <MODE> key twice.
4.
Select the SYSTEM MENU and press <ENTER>.
5.
Press Arrow Down to “14 Installer Setup” and press <ENTER>.
6.
Select “Save Installation Settings”, Toggle to YES and press <ENTER>.
7.
Press Arrow Down to the 3rd page to “Number of Lanes at This Site”, press <ENTER>, press Arrow UP
and then press <ENTER>.
8.
The number of Lanes at this site will now show “2”.
9.
Press <MODE> key 3 times to return to the main menu.
Changing Your Settings
From the Main Menu Screen:
1.
Enter the installer pass code 12345 on the keypad and press <MODE> key twice.
2.
Select the SYSTEM MENU and press <ENTER>.
3.
Select “1 Drive Thru Volume” and press <ENTER>.
4.
Once settings are complete for LANE 1, press <LANE> key in order to change to LANE 2.
5.
If you need to set up a Tandem Lane, Select “7 Global Settings”, switch to LANE 2 and turn on “Please
Pull Ahead” Message.
6.
Press <MODE> key 3 times to return to the Main Menu.