Installation Manual
Table Of Contents
- A. Safety Information 3
- B. Other Conventions 5
- A. Overview of Installation 7
- B. Required Materials (Not Supplied) 7
- C. Design the Installation 7
- D. Install the Battery Charger 9
- E. Install the Order Point Speaker and Microphone Assemblies 12
- F. Install the Vehicle Detector(s) 13
- G. Assemble the PAR Drive Thru Headset G5. 13
- H. Install the Basestation 15
- I. Connect the Components 17
- J. Basestation to Component Wiring 20
- K. Auxiliary Detector Relays 21
- L. Installing Accessory Boards in the Basestation 23
- M. Power Up 26
- A. Enter Configuration Mode 28
- B. Navigating the Basestation Display 28
- C. Finding the MAC Address of the G5 Basestation 30
- D. Configuring with a Computer 30
- E. Logging into the Base Station with a PC 31
- F. Switching Between Lane1 and Lane2 31
- G. Menu Options for Lane1 and Lane2 32
- H. Change Basic Volume Settings 33
- I. Change Noise Reduction Level 39
- J. Set System Date and Time 39
- K. Change Global Settings 39
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets 42
- M. Order Taking Modes Setup 43
- N. Change Site Scheduling 43
- O. Change Site Information 44
- P. Digital IO Setup 45
- Q. Change Passcodes 45
- R. Split and Cross Lane Mode 46
- S. Installer Setup 46
- T. Factory Setup (Restore Factory Defaults) 47
- U. Create and Load Templates 47
- V. Reboot System 47
- W. Check the Revision Levels 48
- 1. Overview
- 2. Installation
- A. Overview of Installation
- B. Required Materials (Not Supplied)
- C. Design the Installation
- D. Install the Battery Charger
- E. Install the Order Point Speaker and Microphone Assemblies
- F. Install the Vehicle Detector(s)
- G. Assemble the PAR Drive Thru Headset G5H1
- H. Install the Basestation
- I. Connect the Components
- J. Basestation to Component Wiring
- K. Auxiliary Detector Relays
- L. Installing Accessory Boards in the Basestation
- M. Power Up
- 3. Configuration
- A. Enter Configuration Mode
- B. Navigating the Basestation Display
- C. Finding the MAC Address of the G5 Basestation
- D. Configuring with a Computer
- E. Logging into the Basestation with a PC
- F. Switching Between Lane1 and Lane2
- G. Menu Options for Lane1 and Lane2
- H. Change Basic Volume Settings
- Inbound Microphone Volume
- Outbound Talk Volume
- Vehicle Alert Volume
- Outbound Greeter Message Volume
- Change the Monitor Volume
- Inbound Listen
- Outbound Talk
- Vehicle Present
- Vehicle Approach
- Page Messages
- Greeter Messages
- Monitoring Audio Separately for the Two Lanes
- Change the Night Volume
- Registering Headsets
- Add Headsets
- Remove Headsets
- List All Headsets
- Resetting Inactive Days
- Checking Headset Software Revision
- Identifying Headset Serial Number
- I. Change Noise Reduction Level
- J. Set System Date and Time
- K. Change Global Settings
- L. Haptics “Vibration” Alerts and Blue LED Alerts on Headsets
- M. Order Taking Modes Setup
- O. Change Site Information
- P. Digital IO Setup
- Q. Change Passcodes
- R. Split and Cross Lane Mode
- S. Installer Setup
- T. Factory Setup (Restore Factory Defaults)
- U. Create and Load Templates
- V. Reboot System
- W. Check the Revision Levels
- X. Change the Microphone Preamp Gain
- Y. Installer Access
- 4. Troubleshooting
- 6. Appendix: Basestation Specifications
- 7. Appendix: Induction Loop and Vehicle Detector Board Specifications
- 8. Appendix: G5 Charger Specifications
- 9. Appendix: Best Practices
- 10. Appendix: PAR Acoustic Kit Installation Guide
- 11. Appendix: Loop and Cable Condition Test
- 12. Appendix: Upgrading a Single Lane Basestation to a Dual Lane
- 13. Index
13.
Index
12V IN/ OUT 18
A
Acoustic Echo 39
Acoustic Echo Canceller 39
Adding Headsets 37
air hose 9
alert tone, none 52
Audio mode 40
B
Basestation Cover Removal 16
Battery Charger Installation 9
Best Practices 66
C
cable 7
CAUTION Definition 3
Charger 54
Component Wiring 20
conduit 7
Configuration 7
Cover 16
Create templates 47 cut
out, headset 52
D
Date 39
Dead battery 50
Dimensions 63, 65
Display 29
Display, navigating 28
Dual Drive-Thru 9
E
Echo 39
Enter (Select) button 29
Ethernet port 30
F
Factory Settings 47
FCC 6
feedback 52
Full duplex 40
G
Global Settings 39
GND 18
Green light, charger 54
Greeter Messages 36
H
Half duplex, definition 40
Hands free, not working 53
Holiday scheduling 44
I
IC Information 6
Inbound Listen 34
Input Power 65
Installation 7
Installation Settings 46
Intended Use 3
L
Lane crossing 46
Language, prompts 40
Listing headsets 38
Location, basestation 15
M
Materials Required 7
MIC 19
Microphone Preamp Gain 48
Mode (Exit) button 29
Mode, audio 40
Mode, Order Taking 43
Mode, Service 29
Mode, Split lane 46
Mode, talking 52
Monitor Volume 34
N
Night Volume 36
No alert tone 52
No communication 51
Noise Reduction 39
Noise Reduction Level 39
Number of Basestations 9
Number of Vehicle Detectors 9
O
Outbound Greeter Message
Volume 34
Outbound Talk Volume 34
Overview 3
P
Page Channel 40
Page Messages 35
Paging 35
Passcode 45
Power Up 26
presence 25
Presence detectors 24
prompt, language 40
Prompt, store is now closed 40
Pull Ahead Prompt 41
pulse 24
R
Reboot 47
Registering Headsets 37
Regular Site Schedule 44
Remove Headsets 37
Revision Levels 48
S
Safety Rules 3
Schedule 44
screws 7
Sensitivity 24
Service (Shift) button 29
Side-by-Side Drive-Thru
8
Site Information 44
Site Scheduling 43
Specifications 63, 64, 65
Store is Now Closed Prompt 40
T
talking mode 52
Tandem Drive-Thru 8
Templates 47
Terminal 17
Time 39
Troubleshooting 49
U
User Passcodes 45
V
Vehicle Alert Volume
34 Vehicle Approach 35
Vehicle Detector 9, 13, 24
Vehicle Present 35
Volume 33
Volume, inbound microphone 33
Volume, Monitor 34
Volume, night 36
Volume, outbound greeter
message 34
Volume, outbound talk 34
Volume, vehicle alert 34
W
Warning, definition 3
Wiring 20