02595 P12597RB Instruction manual Manuel d’instructions Manuale di istruzioni Anleitungshandbuch Manual de las instrucciones Instructieboekje Please read these instructions carefully and make sure you understand them before using this machine. Bitte lesen Sie diese Anleitungen sorgfältig durch und vergewissern Sie sich, daß Sie diese verstehen, bevor Sie die Maschine in Betrieb nehmen. 532 43 41-42 Rev. 2 Merci de lire trés attentivement le manuel d'instructions.
1 Safety rules. Sicherheitsvorschriften. Règles de sécurité. Montaje. Montaggio. Montering. 2 Assembly. Zusammenbau. Montage. Descripción del funcionamiento. Funzionamento. Beschrijving van functies. 18 3 Functional description. Funktionsbeschreibung. Description du fonctionnement. Antes del arranque. Prima dell’avviamento. Maatregelen vóór het starten. 37 4 Before starting. Maßnahmen vor dem Anlassen. Avant de démarrer. Conducción. Guida. Rijden. 45 5 Driving. Betrieb. Conduite.
1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. III. OPERATION I. TRAINING • • Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. • Never allow children or people unfamiliar with the instructions to use the lawnmower.
• • Stop the engine and disengage drive to attachment - before refueling; - before removing the grass catcher; - before making height adjustment unless adjustment can be made from the operator’s position. Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing. IV. MAINTENANCE AND STORAGE • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.
1. Sicherheitsvorschriften Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN. • I. SCHULUNG • Die Anleitungen sorgfältig durchlesen. Mit den Bedienungselementen und der vorschriftsmäßigen Bedienung der Maschine vertraut machen.
• • • • • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstellen und das (die) Zündkerzenkabel abziehen bzw. den Zündschlüssel abziehen: - vor dem Entfernen von Verstopfungen aus dem Mähwerk oder dem Auswurf; - vor dem Prüfen, Reinigen oder Reparieren des Rasenmähers; - nachdem auf ein Fremdkörper gestoßen wurde.
1. Règles de Sécurité Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS. L’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES. • • I. PRÉCAUTIONS D’UTILISATION • Lisez toutes les instructions soigneusement. Familiarisez vous avec les commandes pour appprendre à utiliser efficacement cette machine.
• • • • • Débrayer les lames, arrêter le moteur, et débrancher le (s) fil (s) de (s) bougie (s) d’allumage ou retirer la clef de contact : - avant de retirer l’insert broyeur ou avant de retirer la goulotte d’éjection pour la nettoyer. - avant de contrôler, nettoyer ou travailler sur le carter de coupe, - avant de retirer un objet coincé dans le tracteur de pelouse.
1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. I. INSTRUCCIÓN • • Lea todas las instrucciones cuidadosamente.
• • • • Desenganche la transmisión a los accesorios, pare el motor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora; - después de golpear un objeto extraño.
1. Norme Antinfortunistiche Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. • • I. ADDESTRAMENTO ALL’USO Studiare attentamente le istruzioni. Acquisire dimestichezza con i comandi e conoscere a fondo l’uso corretto dell’equipaggiamento.
• • • • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele oppure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e prima di stasare lo scivolo; - prima di interventi o controlli sul tosaerba e prima delle operazioni di pulizia; - dopo aver colpito un oggetto estraneo.
1. Veiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. • I. TRAINING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken.
• • • • • Schakel de aandrijving naar de hulpstukken uit, stop de motor en maak de bougiekabel(s) los of verwijder het contactsleuteltje, - voordat u opgehoopt materiaal weghaalt of een verstopte afvoer leeg maakt; - voordat u de maaimachine controleert, schoonmaakt of eraan werkt; - nadat u een ongewenst voorwerp heeft geraakt. Inspecteer de maaimachine op schade en voer reparaties uit voordat u de machine weer start en gebruikt; - als de machine abnormaal begint te trillen (onmiddellijk controleren).
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent se montrer sur votre machine ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent se montrer sur votre machine ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
01738 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLETZUNGEN VERURSACHEN. ZU VERMEIDEN: • FUNKEN • FEUER • RAUCHEN SCHWEFELSÄURE KANN ERBLINDUNG ODER SCHWERE VERÄTZUNGEN VERURSACHEN. AUGEN UNVERZÜGLICH MIT WASSER AUSSPÜLEN. SOFORT ÄRZTLICHE HILFE AUFSUCHEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. GEEN • VONKEN • VUUR • ROKEN ZWAVELZUUR KAN BLINDHEID OF ERNSTIGE BRANDWONDEN VER-OORZAKEN. OGEN ONMIDDELLIJK MET WATER SPOELEN.
2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Before the tractor can be used certain parts must be assembled, which for transportation reasons are enclosed in the packing. Antes de poder utilizar el tractor, hay que montar algunas piezas que, por razones de transporte, van empaquetadas en el embalaje. Vor der Anwendung des Aufsitzmähers müssen gewisse Teile eingebaut werden, die aus Transportgründen in der Verpack-ung lose beigefügt sind.
2 1 2 02701 1 02466 02617 Asiento Seat Remueva la manilla de ajuste y la arandela plana que aseguran el asiento al empaque de cartón y póngalos de lado para poder utilizarlos durante la instalación del asiento sobre el tractor. Gire el asiento hacia arriba y remuevalo del embalaje de cartón. Remueva y desechese del embalaje de cartón. Colocar el asiento y en el asiento del recipiente de manera que la cabeza del bulón de la espalda esté posicionada en el agujero ancho ranurado en el recipiente.
2 NOTE! Check that the flex connector is correctly connected to the safety switch (3) on the seat holder. HINWEIS! Prüfen, daß das Kabel richtig an dem Sicherheitsschalter (3) auf dem Halter des Sitzes angeschlossen ist. REMARQUE: Vérifier que le câble électrique est bien connecté sur le contacteur de sécurité (3) placé sous l'embase du siège. NOTA! 3 Controlar que el cable está correctamente acoplado al interruptor de seguridad (3) en el soporte del asiento.
2 1. 2. 3. 4. 5. 6. Battery Cover Cable Positive (+) Cable Negative (-) Fender Battery terminal Battery 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. Batterieabdeckung Positives Kabel (+) Negatives Kabel (-) Schutzblech Batterieklemme Batterie 1. Coperchio dellí accumulatore 2. Cavo elettrico positivo (+) 3. Cavoelettriconegativo(-) 4. Paraurti 5. Polo della batteria 6. Batteria 1. 2. 3. 4. 5. 6. Capotage de batterie Câble (+) Câble (-) Carrosserie Borne de la batterie Batterie 1. 2. 3. 4. 5. 6.
2 WARNING: Positive terminal must be connected first to prevent sparks from accidental grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth cable to -. Screw tight the cables. Grease the battery poles with vaseline to prevent corrosion. Replace battery cover. WARNUNG! Um einen Kurzschluß zu vermeiden, muß der Pluspol zuerst angeschlossen werden. Die Schutzkappen von den Anschlußklemmen entfernen und entsorgen. Die Batterie in Position neben den Fahrersitz bringen.
2 PARA AJUSTAR LAS RUEDAS CALIBRADORAS (si está provisto) Las ruedas calibradoras están bien ajustadas cuando se encuentran un poco a distancia del terreno al mismo tiempo que la segadora esté a la altura de corte deseada. Entonces las ruedas calibradoras mantienen el conjunto segador en posición para prevenir el corte raspeo en casi todos los terrenos. • Ajuste las ruedas calibradoras con el tractor en una superficie nivelada plana.
2 To install bagger components to tractor 2 1 3 2 1. Discharge Chute 2. 3/8 Nut 3. Flat Washer • • 3 02 1. 2. 3. 4. 5. Support Bracket Clevis Pin 10 x 17mm 3/8 Lock Nut 3/8 x 63,5mm Hex Bolt 10,3mm (13/32") flat washer 6. Retainer Spring 27 7 Remove discharge chute from rear of tractor. Unhook the two (2) straps and pull chute out and away from tractor. Remove the two (2) 3/8 nuts and flat washers from the bolts at the tractor back plate.
2 1. Front bagger tube 2. Vinyl binding To Assemble Bagger • 02 1 90 Unfold bag by pivoting front bagger tube all the way forward and pressing the bottom vinyl binding onto the tube. • Inside the bag, install spreader bars and retainer springs onto pins on both sides of bag as shown. • Press the vinyl bindings onto the sides of front bagger tube. • Slide the bagger dump handle through the hole in the bagger top, install the clevis pin 10 x 44mm and secure with retainer spring.
2 Installation der Aufhängung der Grasfangbox des Traktors 2 1 1. Auswurfkanal 2. Kontermutter 3/8 3. Flache unterlegscheibe 3 Strebe Fixierfeder 10x17mm 1 Kontermutter 3/8 Sechskantbolzen 3/8 x 63,5mm 5. Flache Unterlegscheibe 10,3mm (13/32) 6. Splintstift 1. 2. 3. 4. 2 3 02 27 7 • • • Nehmen Sie den Auswurfkanal aus dem hinteren Teil des Traktors. Lösen Sie beide (2) Klammern und ziehen Sie den Kanal aus dem Traktor.
2 1. 2. • 02 1 3. 4. 5. 90 5 2 3 Spreizstäbe Splintstift Vinylverkleidung 4 Justieren der Grasfangbox Um die einwandfreie Funktion der Grasfangbox zu gewährleisten, ist es notwendig, daß die Box richtig justiert wird. Zwischen dem oberen Teil der Box und dem Schutzblech des Trakors soliten 6 mm (1/4") -9mm (3/8") Abstand eingehalten werden. Desweiteren sollte die Oberseite der Box und das Schutzblech des Traktors in einer Flucht liegn: 5 4 6 90 02 • 6. 7. 8. 9.
2 Assemblage des composants du collecteur 2 1. Bras support supérieur 2. C h e v i l l e d e f i x a t i o n 10x17mm 3. Ecrou frein 3/8 3 4. Vis H 3/8 x 63,5 5. Rondelle plate diam. 10,3 mm (13/32") 1 5 6. Epingle 1 2 1. Goulotte d'éjection 2. Ecrou 3/8 3. Rondelle plate 3 02 4 6 03 02 8 27 7 • • Retirer la goulotte d'éjection (1). Pour cela, libérer les deux attaches élastiques à l'arrière du tracteur et tirer la goulotte d'éjection hors du tracteur.
2 1. 2. • 3. 4. 5. Déplier le sac en faisant basculer complètement vers l’avant le tube antérieur de l’ensacheuse et en poussant la bordure inférieure en vinyle sur le tube. • Dans le sac, placer les entretoises et les ressorts de retenue sur les goupilles des deux côtés du sac, de la façon illustrée. • Enfoncer les bordures en vinyle sur les deux côtés du tube antérieur de l’ensacheuse.
2 Para montar los componentes del contenedor para costales al tractor 1. Consola portadora 2. Resorte fijador 10x17mm 3. Contratuerca 3/8 4. 3/8x63,5mm arandelas planas 5. Arandela plana 10,3mm (13/32î) 6. Clavija hendida 1 2 1. Descarga de adaptarse 2. Tuercas de 3/8 3. Arandelas planas 3 • 3 1 5 4 6 02 27 03 02 7 8 • • 2 Quite el colector de la parte trasera del tractor. Desbloquee las dos (2) grapas y tire el colector fuera del tractor.
2 1. 2. Tubos frontales del contenedor Capas de vinil • 9 02 1 3. 4. 5. Desplegar la bolsa pivoteando el tubo frontal del saco completamente hacia adelante y presionado la atadura de vinilo del fondo hacia el tubo. • En el interior de la bolsa, instalar las barras extendedoras y los resortes de retención en las clavijas en ambos lados de la bolsa como mostrado. • Presionar las ataduras de vinilo en los lados del tubo frontal del saco.
2 1. Staffa di supporto 2. Perno di fissaggio 10x17mm 3. Dadi 3/8 4. Bullone a testa esagonale (3/8 x 63,5mm) 5. Rondella piatta 6. Coppiglia Per montare i componenti del cesto di raccolta 1 2 1. Convogliatore di scarico 2. Dadi 3/8 3. Rondella Piatta • • 3 2 3 1 5 4 6 03 02 02 8 27 7 Rimuovere il convogliatore dalla parte posteriore del trattore. Allentare le due graffe, sganciare ed estrarre il convogliatore.
2 1. Piastrina d'arresto dell'asta di scarico 2. Rivestimento in plastica • 02 1 90 Svolgere il sacchetto ruotando completamente in avanti il tubo anteriore dell’insaccatrice e premendo la parte inferiore in vinile sul tubo. • All’interno del sacchetto, installare le barre distanziatrici e le molle di tenuta sui perni di entrambi i lati del sacchetto, come mostrato in figura. • Premere i collegamenti in vinile sui lati del tubo anteriore dell’insaccatrice.
2 Hetmonteren van componenten van de grascontainer op de trekker 2 1 3 2 1. Afvoertrechter 2. 3/8 borgmoer 3. Vlakke sluitring • • 3 1. 2. 3. 4. 5. 6. Stennijzer 1 Vorkbout 10x17mm 5 4 3/8 borgmoer 3/8 Zeskantbout Vlakke sluitring 10,3 mm (13.32") Sluitveer • Bevestig de twee bovenste steunbeugels door de achterplaat en aan het frame. Bevesting de trekpen Vorkbout 10x17mm en zet hem vast met de sluitveer.
2 • Vouw de zak open door de voorste zakkenvulbuis helemaal naar voren te draaien en de onderste band van vinyl op de buis te drukken. • Installeer in de zak de spreiders en de borgveren op de pinnen aan de beide zijden van de zak, zoals op de afbeelding. • Druk de banden van vinyl op de zijkanten van de voorste zakkenvulbuis. • Voer de hendel voor het legen van de container door het gat in de bovenkant van de container, bevesting de trekpen en zet hem vast met de sluitveer.
2 1 2 A 3 A 4 1. 2. 3. 4. Handle Retainer Spring Pin Plug 1. 2. 3. 4. Mango Resorte fijador Clavija Tapon o tapa 1. 2. 3. 4. Handgriff Fixierfeder Stift Stöpsel 1. 2. 3. 4. Impugnatura Coppiglia Perno Kit Mulching 1. 2. 3. 4. Poignée de l'insert Epingle Axe de fixation Tête de l'insert 1. 2. 3. 4. Hendel Sluitveer Pen Plug To assemble and install mulcher plug (if equipped) • • • Para ensamblar y montar la tapa mulching (si está provisto) Remove spring retainer and pin from handle.
3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies 7 5 11 1 6 3 2 8 4 Anordnung der Bedienungseinrichtungen 1. Lichtschalter (sofern vorhanden) 2. Gashebel 3. Brems- und Kupplungspedal 4. Schalthebel 5. Ein- und Ausschalten des Mähaggregats 6. Schnelles Heben und Senken des Mähaggregats 7. Zündschloß 8. Feststellbremse 11. Kalstartregler Positioning of controls 1.
3 7 5 11 1 6 3 2 8 4 Emplacement des commandes 1. 2. 3. 4. 5. 6. 7. 8. 11. Comandi 1. Interruttore luci (se installato) 2. Acceleratore 3. Pedale freno/frizione 4. Leva del cambio 5. Inserimento/disinserimento del dispositivo di taglio. 6. Sollevamento/abbassamento del tagliaerba 7. Chiave di accensione 8. Freno di parcheggio 11.
3 1. Light switch 1. Lichtschalter 7 34 1. Interrupteur des phares 01 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2. Gashebel Mit dem Gashebel wird die Drehzahl des Motors und damit die Drehgeschwindigkeit des Mähaggregats geregelt. = Vollgas = Leerlauf 2.
3 3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abgebremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus. 01 3 3. Pédale d'embrayage et de frein 58 En appuyant sur cette pédale, la transmission se débraye et le frein entre en action simultanément. 3.
3 4. Palanca de cambios La caja de cambios tiene posiciones hacia adelante, punto neutro y marcha atrás. Los cambios pueden efectuarse desde el punto neutro a la marcha más alta sin detenerse en cada posición de cambio. Antes de cambiar de marcha, desembragar el motor. El arranque puede hacerse independientemente de la posición de la palanca de cambios. NOTA! Pare la máquina antes de pasar de la marcha atrás a una marcha adelante, o inversamente.
3 5. Commande d'embrayage et de débrayage du carter de coupe Pousser le levier vers l'avant et le verrouiller pour embrayer le carter de coupe. Les courroies d'entraînement seront alors en tension et les lames commenceront à tourner. Ramener le levier vers l'arrière pour débrayer le carter de coupe, les lames seront alors freinées par le frottement des patins de frein sur les poulies d'entraînement. 5.
3 02927 OFF ROS ON ON 7. Ignition Lock There are three different positions for the ignition key: OFF All electric current broken. ROS ON Reverse Operation System (ROS) connected ON Electric current connected. START Start motor connected. Reverse Operation System (ROS) - Allows operation of mower deck or other powered attachment while in reverse (See section 5 - "Driving") WARNING! Never leave the key in the ignition lock when leaving the machine on its own. 7.
3 8. Frein de stationnement 01 3 Pour enclencher le frein de stationnement : 1. Enfoncer à fond la pédale d'embrayage/frein. 2. Relever vers le haut le levier du frein de stationnement et le maintenir dans cette position. 3. Relâcher la pédale d'embrayage/frein. Relâcher le levier du frein de stationnement qui restera dans sa position verrouillée (en haut).
4. Before starting. 4. Maßnahmen vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Reposición de combustible Filling up The engine should be run of pure (not oil mixed) unleaded petrol. Do not fill beyond the lower edge of the filling hole. Do not fill over max level. El motor ha de funcionar con gasolina pura (sin mezcia de aceite), sin plomo. El nivel no ha de sobrepasar el borde inferior del orificio de llenado.
4 Oil level Nivel de aceite The combined oil refilling cap and the oil stick is accessible when the bonnet is lifted forwards. The oil level in the engine should be checked before each run. Make sure that the tractor is horizontal. Unscrew the oil stick and wipe clean. Replace the oil stick and screw tight. Remove again and check the level. La tapa combinada para el llenado de aceite y para la varilla de nivel queda accesible después de haber levantado hacia adelante el capó del motor.
5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Démarrage du moteur S'assurer préalablement que le carter de coupe est en position de transport (c'est à dire : relevé au maximum) et que le levier d'embrayage et de débrayage du carter de coupe est en position "débrayée" (voir figure).
5 Bei warmem Motor: Gashebel in die Vollgasstellung " schieben. " Si le moteur est chaud: pousser la commande des gaz à mi-distance de sa position d'accélération maximale" ". Moter caliente: Empuje el acelerador hasta la mitad de su recorrido hacia la posición de plenos gases " ". Motore caldo: Portare il comando del gas sul massimo " ". Bij een warme motor: Schuif de gashendel halverwege naar de volgaspositie " ". Warm motor: Push the gas control half-way to full gas position " ".
5 NOTE! NOTA! The machine is equipped with a safety switch which immediately breaks the current to the engine if the driver leaves the seat with engine running and with the connection/disconnection lever in position “connection”.Your machine is also equipped with a system that will not allow mower to operate if the bagger or optional rear discharge deflector is not installed properly.
5 ROS "ON" ROS "AN" ROS "ON" ROS "ON" ROS "ON" ROS "ON" 02828 Engine "ON" (Normal Operating) Motor "AN" (Normalbetrieb) Moteur "ON" (Fonctionnement normal) Motor "ON" (Funcionamiento Normal) Motore "ON" (Funzionamento normale) Motor "ON" (normaal functioneren) Sécurité Marche Arrière (ROS) Reverse Operation System (ROS) Votre tracteur est équipé d’un dispositif de sécurité de fonctionnement en marche arrière (ROS).
5 Sistema per operazioni in retromarcia (ROS) Cutting tips Il Vostro trattore possiede un Sistema per operazioni in retromarcia (ROS). Qualsiasi tentativo da parte dell’operatore di guidare nella direzione opposta con la frizione abbassata comporterà lo spegnimento del motore se la chiave di accensione non è inserita nel ROS nella posizione "ON". ATTENZIONE! Fare retromarcia con la frizione abbassata durante la guida è sconsigliato.
5 Conseils pour la tonte • • • • • • • Consigli per il taglio dell’erba Retirer de la pelouse, les pierres et autres objets qui pourraient être propulsés par les lames et devenir ainsi des projectiles dangereux. Localiser et marquer les pierres et autres obstacles fixes afin d'éviter une éventuelle collision pendant la tonte. Commencer par couper assez haut, puis réduire progressivement cette hauteur de coupe jusqu'à obtention du résultat souhaité.
5 Pour vider le bac Votre tracteur est muni d’une alarme de bascule du sac. Pour désactiver l’alarme, désengager la commande de l’embrayage. • Amener le tracteur là ou vous souhaitez le décharger. • Vérifier que la boîte de vitesse est au point mort. Engagez le frein de stationnement. • Tirer le leiver de vidange du bac vers le haut puis vers l'avant afin d'ouvrir le bac et vider l'herbe coupée. • Remettre ensuite le levier dans sa position initiale.
5 To convert mower • (Converting to mulching or rear discharging will require the purchase of these accessories.) • To mulching Place deck into the high cut position. Remove bagger or optional rear discharge deflector. Unhook the two (2) straps and remove discharge chute. • Insert plug and handle assembly through back plate and onto the mower deck chute adaptor. • Retain the plug assembly by connecting the two straps over the handle and hook into the holes provided.
5 • • Para cambiar el ajuste de la segadora (Un cambio de ajuste para no recoger la hierba o usarla tipo mulching requiere la compra de los mecanismosdispositivos siguientes) • • • • • • • • • • • • • Para cortar tipo mulching Meta la plataforma en posicion de siega alta Quite el recogedor y/o el deflector Desmonte las dos (2) grapas y quite el deflector Introduzca el tapón y el mango por la placa de atras y sobre la alargadera (adaptador) del canal de descarga inferior de la segadora Fije el bloque lig
5 ATTENTION! • • • Ne jamais utiliser un tracteur sur des pentes excédant 15°. Les risques de renversement étant alors très importants. Ne jamais rouler parallèlement à la pente du fait des risques de renversement. Toujours rouler perpendiculairement à la pente, aussi bien en montant, qu'en descendant. Ne jamais arrêter ou démarrer un tracteur en pente. ADVERTENCIA! • • • WARNING! • • • PERICOLO! Do not drive in terrain at an angle of more than max. 15°. The risk for roll-over backwards is large.
5 Switching off the engine Move the attachment clutch control to disengaged position. Move the throttle control between half and full speed (fast) position. Lift up the cutting unit and turn the ignition key to “STOP” position. Abschalten des Motors Stellen Sie die Steuerung der Anhängerkupplung auf ausgekuppelt. Bewegen Sie die Gassteuerung auf die (fixe) Position zwischen halber und voller Geschwindigkeit. Heben Sie das Mähgerät hoch und drehen Sie den Zündschlüssel auf „STOPP“-Position.
6. Maintenance, adjustment. 6. Wartung (Instandhaltung), Einstellung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! ADVERTENCIA! Antes de proceder a efectuar el servicio en el motor o en el equipo de corte, hay que hacer lo siguiente: • Apretar el pedal del embrague/freno y acoplar el freno de estacionamiento. • Poner la palanca de cambios en punto neutro. • Poner la palanca de embrague en posición desembragada. • Parar el motor.
6 Engine hood • • • 1 • • Raise hood. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt forward and lift off of tractor. To reinstall, slide hood pivot brackets into slots in frame. Reconnect headlight wire connector and close hood. Motorhaube • • • • 02495 • Motorhaube hochklappen. Scheinwerferanschluß lösen. Vor den Mäher treten. Motorhaube an den Seiten anfassen, nach vorn kippen und aus dem Mäher herausheben.
6 Maintenance Mantenimiento NOTE: Periodic maintenance should be performed on a regular basis in order to keep your tractor in good running condition. WARNING: Disconnect spark plug wire to prevent accidental starting before attempting any repair, inspection, or maintenance. Before each use: • Check oil, lubricate pivot points as necessary. • Check to see all bolts, nuts, and cotter pins are in place and secure. • Check the battery, terminals and vents. • Recharge slowly at 6 amperes if needed.
6 PARA CAMBIAR EL ACEITE ATENCIÓN: El aceite estará caliente si el motor ha estado funcionando durante un tiempo prolongado inmediatamente antes de drenarlo. • Deslice el extensor de drenaje del aceite sobre el chasis situado por debajo del orificio de drenaje. • Coloque un recipiente debajo del extensor de drenaje para recoger el aceite. • Afloje y retire el tapón de drenaje del aceite con una llave de vaso de 1/2 pulgadas (12 puntos) (recomendada para el extensor).
6 SERVICE RECORD Fill in dates as you complete regular service. As Needed Every 8 hours Every 25 hours Change engine oil (without oil filter) ................................................... Every . 50 hours Every . 100 hours • Change engine oil (with oil filter) ................................................................................................. Lubricate pivot points ......................................................................... Check brake operation .....................
6 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Selon les besoins Toutes les 8 H Toutes les 25 H Vidange de l'huile moteur Toutes les 50 H Toutes les 100 H Toutes les 200 H • (sans filtre à huile) .................................................................................... Vidange de l'huile moteur (avec filtre à huile) ...............................................................................................................................
6 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio. Necessità Ogni 8 ore Ogni 25 ore Cambio dell'olio (Senza filtro dell’olio)................................................ Ogni . 50 ore Ogni 100 ore • Cambio dell'olio (Con filtro dell’olio) ............................................................................................ Lubrificazione punti di articolazione ................................................... Controllo freni ......................................
6 Operator Presence System and Reverse Operation System (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.
6 Sistema de Presencia Operador y Sistema de Funcionamiento Atrás (ROS) Asegurarse de que los sistemas de presencia operador y funcionamiento atrás funcionen adecuadamente. Si tu tractor no funciona como descrito, hay que reparar el problema inmediatamente. • El motor no tiene que arrancar hasta que le pedal del freno no esté completamente presionado, y el mando del embrague esté en la posición desembragada.
6 Blades Cuchillas The blades should be sharp to achieve best cutting results. Sharpening can be carried out with a file or grinding disc. NOTE: It is very important that both blades are sharpened equally to avoid imbalance. Las cuchillas han de estar afiladas para proporcionar el mejor corte posible. El afilado puede hacerse con lima o muela. NOTA: Es muy importante que los dos lados de la cuchilla sean afilados igual a in de impedir desequilibrios.
6 8 7 LH 1. 2. 3. 4. 5. 6. 7. 8. Hex bolt right hand threaded. Lock Washer Flat Washer Blade 5 Star Center Hole 5 Star Pattern Trailing Edge Mandrel Assembly 1. Sechskantschraube mit Rechtsgewinde 2. Federscheibe 3. Flache Unterlegscheibe 4. Schneidmesser 3 6 2 1 5. Orifice de fixation central (étoile) à cinq branches. 6. Moyeu 7. Volute 8. Support de lame 1. 2. 3. 4. 5. 6. 7. 8. Hex bolt left hand threaded.
6 8 7 1. 2. 3. 4. 5. 6. 7. 8. 1. 2. 3. 4. 1. 2. 3. 4. Tornillo de cabeza de cinco facetas, dextrogiro Arandela elastica Arandela plana Filo cortador Orifico de centrajeestrella de cinco puntas Mandril-estrella de cinco puntas Canto (auxiliar cortador) trasero Nudo del mandril LH 3 6 2 5 4 1 Bullone a testa esagonale 5. con filettatura destrorsa Rondella elastica 6. Rondella piatta 7. Lama 8.
6 For best results mower blades must be kept sharp. Replace bent or damaged blades. BLADE REMOVAL • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and flat washer securing blade. • Install new or resharpened blade with trailing edge up towards deck as shown. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. • Reassemble hex bolt, lock washer and flat washer in exact order as shown.
6 Controlar El Freno To Check Brake Si el tractor requiere más de cinco (5) pies para pararse a la velocidad más alta en la marcha más alta en una superficie nivelada seca en hormigón o adoquinada, hay que reparar el freno. If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1.
6 Desmontaje de la unidad de corte 2 3 Trabajar desde el lado derecho de la máquina. 1. Quitar después la correa de la polea del motor (1). 2. Quitar los dos resortes posteriores (2) y golpear con un martillo los muñones de eje hasta sacarlos. 3. Quitar los resortes (3), (4), (5) y los ejes respectivos. 4. Tirar hacia atrás de la palanca para la elevación y descenso de la unidad de corte. 5. Extraer la unidad de corte de la máquina.
6 Cambio de la correa propulsora del equipo de corte Replacement of drive belt for cutting unit 1. Dismantle the cutting unit as described previously. 2. Work off the belt from the unit's left pulley and then from the other wheels. 3. Pull the belt away from the cutting unit. 4. The new belt is mounted in the reverse order. Check that the belt lies inside all the belt guides. 1. Desmontar el equipo de corte del tractor. 2. Quitar la polea izquierda de la unidad y después de las otras poleas. 3.
6 2 A 1 B Adjustment of the cutting unit 1. 2. 3. 4. A. In the direction of travel Check that the air pressure is correct in all four tires. Make sure that the machine is on a horizontal surface. Lift up the cutting unit to its highest position. Measure the distances A and B. To achieve best cutting results the cutting unit’s front edge (B) should be about 10 mm (0.375") lower than the back edge (A). Adjust in the following way to raise the back edge: 1.
6 1 • • Relever le carter de coupe au maximum. A partir du milieu de chaque extrémités latérales du carter de coupe, mesurer la distance du bord du carter par rapport au sol . • La distance (A) doit être la même des deux côtés à 6 mm près. • Si un réglage est nécessaire, ne l'effectuer que d'un seul côté en se référant à l'autre côté. • Abaisser ou soulever un côté du carter de coupe en ajustant la position de l'écrou de réglage de ce côté.
6 Cambio de correa propulsora 1. Desmontar el equipo de corte del tractor. 2. Desmontar el limitador de movimientos del acoplamiento (1). 3. Aplicar el freno de estacionamiento y tirar hacia arriba de la correa para sacarla de la rueda libre (2), de la acoplamiento (3). 4. Introducir la correa entre dos aspas del ventilador y hacer girar éste a izquierdas hasta que queda libre la correa (4). 5. Quitar después la correa de la polea del motor (5). 5 2 Sostituzione della cinghia di trazione 3 1.
6 1 EINSTELLUNG DES SCHALTHEBELS DES DIFFERENTIALGETRIEBES 02239 3 Das Differentialgetriebe muß sich in Leerlaufstellung befinden, wenn der Schalthebel in der Neutral-Stellung (N) (Verschlußsperre) steht. Diese Einstellung wird bereits vom Hersteller im Werk durchgeführt. Sollte es jedoch dennoch erforderlich sein, weitere Einstellungen vorzunehmen, so muß folgendermaßen vorgegangen werden: • Zunächst muß sichergestellt werden, daß sich das Differentialgetriebe in Leerlaufstellung (N) befindet.
6 1 02239 3 2 REGOLAZIONE DELLA LEVA DEL MECCANISMO DEL CAMBIO DI VELOCITÀ CON DIFFERENZIALE Il meccanismo del cambio con differenziale deve essere in posizione di folle quando la relativa leva è in posizione di folle (N) (blocco). Tale condizione viene impostata al momento della fabbricazione.
7. Troubleshooting. 7. Störungssuche. 1. 2. 3. 4. 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 1. 2. 3. 4. 5. 6. Engine will not start 1. 2. 3. 4. No fuel in fuel tank. Plug defective. Plug connection defective. Dirt in carburetor or fuel pipe. Start motor will not turn engine 1. 2. 3. 4. 5. 6. 7. Battery flat. Poor contact between cable and battery pole. Connection/disconnection level in wrong position. Main fuse defective. Ignition lock defective.
7. Recherche des pannes. 7. Búsqueda de averías. 1. 2. 3. 4. Le moteur ne démarre pas 1. 2. 3. 4. Manque de carburant dans le réservoir. Bougie d'allumage défectueuse. Le câblage de la bougie d'allumage défectueux. Il y a des impuretés dans le carburateur ou dans le circuit du carburant. Le démarreur n'entraîne pas le moteur 1. 2. 3. 4. 1. Batería descargada. 2. Mal contacto entre cable y borne de batería. 3. La palanca de acoplamiento/desacoplamiento en mala posición. 4. Fusible principal estropeado.
7. Ricerca guasti. 7. Het localiseren van fouten. 1. 2. 3. 4. 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 1. 2. 3. 4. 5. 6. Il motore non parte Manca il carburante. Difetto di candela. Collegamento della candela difettoso. Sporco nel sistema di alimentazione e o nel carburatore. 1. 2. 3. 4. Il motorino di avviamento non fa girare il motore Batteria scarica. Difetto di contatto tra cavo e polo della batteria. Leva di inserimento del tagliaerba in posizione errata. Fusibile principale bruciato.
8. Storage. 8. Aufbewahrung. 8. Remisage. 8. Conservación. The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cutting unit cover. Do not use high pressure washer for cleaning. Water can enter engine and transmission and shorten the useful life of the machine. • Touch up all chipped paint surfaces in order to avoid corrosion. • Change engine oil. • Drain the fuel tank. Start the engine and allow it to run until it is out of fuel.
8. Rismessaggio. 8. Stallen. Aan het einde van elk maaisezoen moeten de volgende maatregelen worden genomen: • Maak de hele machine schoon, in het bijzonder de binnenkant van de kap van de maaikast. Geen water onder hoge druk gebruiken om het voertuig te reinigen. Er kan water in de motor en in de transmissieorganen komen, wat de levensduur van het voertuig verkort. • Herstel lakbeschadigingen om roest te voorkomen. • Ververs de olie in de motor. • Maak de benzinetank leeg.
2006/42/EC P12397RB 7,72/5,76 0-6,3 97 38-102 235 ISO 11094 2005/88/EC * ISO 3744 2000/14/EC EMC 2004/108/EC EN 1033 A (8) ≤ 2.5 EN 1032 A (8) ≤ 0.5 *As rated by the engine manufacturer Notified Body SNCH 11, Route de Luxembourg L-5230 Sandweiler TUV Rheinland No. 0499 09.21.10 AP Printed in the U.S.A.