350 GB INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference.
IDENTIFICATION (WHAT IS WHAT?) Front Hand Guard Chain Adjustment Tool (Bar Tool) Front Handle Starter Rope ON/STOP Switch Muffler Chain Bar Oil Fill Cap Primer Bulb Starter Housing Fuel Mix Fill Cap Cylinder Cover Throttle Lockout Rear Handle Throttle Trigger Chain Direction of Travel Adjusting Screw Choke Knob Chain Brake Chain Brake Chain Nuts Catcher Guide Bar Bar Sprocket Hole IDENTIFICATION OF SYMBOLS WARNING! This chain saw can be dangerous! Careless or improper use can cause serious o
SAFETY RULES S Carefully plan your sawing operation in advance. Do not start cutting until you have a clear work area, secure footing, and, if you are felling trees, a planned retreat path. WARNING: Always disconnect spark plug wire and place wire where it cannot contact spark plug to prevent accidental starting when setting up, transporting, adjusting or making repairs except carburetor adjustments.
lated place; and use an approved, marked container for all fuel purposes. Wipe up all fuel spills before starting saw. S Move at least 10 feet (3 meters) from fueling site before starting engine. S Turn the engine off and let saw cool in a non-combustible area, not on dry leaves, straw, paper, etc. Slowly remove fuel cap and refuel unit. S Store the unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.
Symmetrical Guide Bar Large Radius Tip Elbow locked S Low--Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow wood to gradually ride into the cutter. Thumb on underside of handlebar Low-Kickback Chain Contoured Depth Gauge Elongated Guard Link Deflects Kickback Force And Allows Wood To Gradually Ride Into Cutter S Keep a good, firm grip on the saw with both hands when the engine is running and don’t let go.
SAFETY NOTICE: Exposure to vibrations loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.
Checking the tension: Use the screwdriver end of the chain adjustment tool (bar tool) to move the chain around the bar. If the chain does not rotate, it is too tight. If too loose, the chain will sag below the bar. Place chain onto the sprocket 7. Place chain over and behind clutch, fitting the drive links in the clutch drum sprocket. 8. Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar. 9. Fit chain drive links into bar groove. 10.
OPERATING YOUR UNIT BEFORE STARTING ENGINE WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CARBURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns. To stop the engine, move the ON/STOP switch to the STOP position. To start the engine, hold the saw firmly on the ground as illustrated below. Make sure the chain is free to turn without contacting any object.
5. Push the choke/fast idle lever in to the HALF CHOKE position. place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer. S This saw is equipped with a chain brake. The brake is designed to stop the chain if kickback occurs. S The inertia activated chain brake is activated if the front hand guard is pushed forward, either manually or by centrifugal force.
S Allow the chain to cut for you. Exert only light downward pressure. S Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. If you run the saw at full throttle without a cutting load, unnecessary wear can occur. S To avoid losing control when cut is complete, do not put pressure on saw at end of cut. S Stop the engine before setting the saw down.
BUCKING USING A LOG OR SUPPORT STAND S Do not cut in an area where logs, limbs, and roots are tangled. Drag the logs into a clear area before cutting by pulling out exposed and cleared logs first. S Remember your first cut is always on the pressure side of the log. S Your first cut should extend 1/3 of the diameter of the log. S Finish with your second cut. TYPES OF CUTTING USED FOR BUCKING Using a log for support WARNING: If saw becomes pinched or hung in a log, don’t try to force it out.
S Keep the tree between you and the chain as much as possible. S Remove larger, supporting branches with the cutting techniques described in BUCKING WITHOUT A SUPPORT. S Always use an overcut to cut small and freely hanging limbs. Undercutting could cause limbs to fall and pinch saw. S Make your fist cut 1/3 of the way through the bottom of the limb. S Next make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch collar from the trunk of the tree.
Air Filter Cylinder Cover Screws Cylinder Cover SPARK PLUG The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and nonadjustable. 1. Loosen 3 screws on cylinder cover. 2. Remove the cylinder cover. 3. Pull off the spark plug boot. 4. Remove spark plug from cylinder and discard. 5. Replace with Champion RCJ--7Y spark plug and tighten securely with a 19 mm socket wrench. Spark plug gap should be 0,5 mm. 6. Reinstall the spark plug boot.
TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE Engine will not start or will run only a few seconds after starting. 1. Ignition switch off. 2. Engine flooded. REMEDY Engine will not idle properly. 1. Idle speed requires adjustment. 2. Carburetor requires adjustment. 1. See “Carburetor Adjustment” in the Service and Adjustments Section. 2.
TECHNICAL DATA SHEET MODEL: Partner 350 ENGINE 36 Cylinder volume, cm3 Stroke, mm 32 Idle speed, rpm 3,000 Recommended max speed, unloaded, rpm 13,000 Power, kW 1,4 IGNITION SYSTEM Manufacturer Walbro Type of ignition system CD Spark plug Champion Electrode gap, mm 0,5 FUEL AND LUBRICATION SYSTEM Manufacturer Walbro Carburetor type WT--662 Fuel capacity, litre 0,38 Oil pump capacity at 8,500 rpm ml/min 4 -- 8 Oil capacity, litre 0,2 Type of oil pump Automatic WEIGHT Without bar and chain, kg 4,7 NOISE LEVEL
Electrolux Home Products, Inc. 104 Warren Road Augusta, GA 30907 UNITED STATES Visit our website at www.electrolux.com/partner Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Electrolux Home Products, Inc. manufacture products for a number of well--known brands under various registered patents, designs and trademarks in several countries. Copyright E2004 Electrolux Home Products, Inc.