Brochure

Pipe Wrap Tape & Sealants
E-2
Lynwood, CA [phone]
Curtis Bay, MD [phone]
3/25/18
Pipe Wrap Primer
• PASCO Pipe Primer is a quick drying
rubber base primer that permeates pits
and irregularities on the pipe surface and
prepares the metal for tape application.
• PASCO Pipe Primer is made to be
compatible with the adhesives on PASCO
Pipe Protection Tape.
• PASCO Pipe Primer is easily brushed on
the pipe and fittings. The application of the
primer enhances the surface preparation
and adds strength adhesion at low cost.
• Pint and quart sizes with dauber.
Pipe Tape Coverage Chart
PART
NUMBER
SIZE
COVERAGE
IN SQUARE
FEET*
9043 Pint 65
9046 Quart 125
1 Square = 100 Square feet of tape
1” Width = 12 Rolls per square
2” Width = 6 Rolls per square
4” Width = 3 Rolls per square
APPLICATION DIRECTIONS
1. Surfaces to be wrapped
must be clean and dry.
Any oil or grease must be
removed.
2. Any burrs or sharp edges
must be removed or
smoothed.
3. Before tape application,
all bare pipe and fittings
to be wrapped must be
coated with PASCO PIPE
PRIMER.
4. Weld beads shall be
covered with one wrap or
layer of tape prior to spiral
wrapping.
5. Tape shall be spirally
wrapped the length of the
pipe using one half lap for
double thickness or 1/2”
overlap, depending on the
individual installation.
6. When pipe is mill coated,
tape must be used on
the fittings and joints. To
wrap a joint, first coat joint
with primer. Joint shall be
wrapped with tape spirally
beginning on the mill coat-
ing 3” from joint. Cover
joint and end tape on mill
coating 3” past joint.
* Approximate:
Depends on surface condition of the pipe
IMPORTANT:
Always use PASCO Pipe Primer
on ALL Pipe-wrapping Jobs!
ID OD
RECOM-
MENDED
TAPE
WIDTH
MINIMUM
TAPE
OVERLAP
SQUARES OF
TAPE NEEDED
PER 100 LINEAL
FEET OF PIPE
––––––––
MINIMUM
OVERLAP
SQUARES OF
TAPE NEEDED
PER 100 LINEAL
FEET OF PIPE
––––––––
HALF-
LAPPED
NUMBER OF
SQUARE FEET PER
100 LINEAL FEET
OF PIPE
1/2” .84” 1” 1/4” .294 .44 22.0
3/4” 1.05” 1” 1/4” .367 .55 27.5
3/4” 1.05” 2” 3/8” .338 .55 27.5
1” 1.32” 1” 1/4” .461 .691 34.6
1” 1.32” 2” 3/8” .425 .691 34.6
1” 1.32” 4” 1/2” .395 .691 34.6
1-1/4” 1.66” 2” 3/8” .535 .869 43.5
1-1/4” 1.66” 4” 1/2” .497 .869 43.5
1-1/2” 1.90” 2” 3/8” .612 .995 49.7
1-1/2” 1.90” 4” 1/2” .568 .995 49.7
2” 2.38” 2” 3/8” .767 1.246 62.3
2” 2.38” 4” 1/2” .712 1.246 62.3
2-1/2” 2.88” 2” 3/8” .928 1.508 75.4
2-1/2” 2.88” 4” 1/2” .862 1.508 75.4
3” 3.50” 2” 3/8” 1.128 1.833 91.6
3” 3.50” 4” 1/2” 1.047 1.833 91.6
3-1/2” 4.00” 2” 3/8” 1.289 2.094 104.7
3-1/2” 4.00” 4” 1/2” 1.197 2.094 104.7
4” 4.50” 2” 3/8” 1.450 2.356 117.8
4” 4.50” 4” 1/2” 1.346 2.356 117.8
4-1/2” 5.00” 4” 1/2” 1.496 2.618 130.9
5” 5.75” 4” 1/2” 1.667 2.916 145.8
6” 6.63” 4” 1/2” 1.984 3.471 173.6
6” 6.63” 6” 1/2” 1.894 3.471 173.6
7” 7.63” 4” 1/2” 2.283 3.995 199.7
7” 7.63” 6” 1/2” 2.179 3.995 199.7
8” 8.63” 4” 1/2” 2.582 4.519 255.9
8” 8.63” 6” 1/2” 2.465 4.519 255.9
Pipe Diameter