MODEL F325R Framing Nailer IMPORTANT! OPERATING MANUAL AND SCHEMATIC DO NOT DESTROY It is the customers responsibility to have all operators and service personnel read and understand this manual. PRINTED IN U.S.A. © 2014, Illinois Tool Works Inc.
INTRODUCTION The Paslode® F325R remodeling framing nailer is a quality-built tool designed for use in residential framing applications. This tool will deliver efficient, dependable performance when used according to the manufactures guidelines. Please study this manual including the safety instructions to fully understand the operation of this tool. TOOL AND FASTENER SPECIFICATIONS ................................................................. 3 SAFETY INSTRUCTIONS .......................................
TOOL AND FASTENER SPECIFICATIONS TOOL SPECIFICATIONS MODEL NO. F325R (Part# 513000) HEIGHT 12.9” WIDTH 4.3" LENGTH 12.3" WEIGHT 5.9 lbs. OPERATING PRESSURE 90 to 120 p.s.i. (6.2 to 8.3 bar) MAGAZINE TYPE 30 degree, Single Strip FASTENER SPECIFICATIONS NAIL LENGTH SHANK DIAMETER 2” - 3-1/4" .113 - .131 TOOL AIR FITTINGS: This tool uses a 3/8” N.P.T. male plug. The tting must be capable of discharging tool air pressure when disconnected from the air supply.
SAFETY INSTRUCTIONS SAFETY FIRST These safety instructions provide information necessary for safe operation of Paslode® framing tools. DO NOT ATTEMPT TO OPERATE THE TOOL UNTIL YOU READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND MANUAL INSTRUCTIONS. DISCONNECT THE TOOL WHEN NOT IN USE Always disconnect the tool from the air line when it is not in use, when you leave the work area or when moving the tool to a new location.
TOOL INSTALLATION TOOL OPERATION Depth of Drive Adjustment Your Paslode tool comes ready for immediate use and can be installed by following these steps: ® 1. SAFETY - All tool operators and their immediate supervisors must become familiar with the operator safety instructions before operating the tool. The instructions are on page 4 of this manual. The depth of drive adjustment can be adjusted two ways. 1.
TOOL OPERATION continued Loading of Nails Step 1 - Grasp the handle firmly. Step 2 - Insert one strip of nails into the rear of the magazine. Step 3 - Pull the follower to the rear of the magazine until it is engaged behind the nails. Sequential Operation The sequential operating kit prevents succesive or "bounce" driving. Depress the work contacting element and hold it against the work surface before pulling the trigger.
AIR SYSTEMS Air hoses are not longer than 150 feet. For air-powered tools to work their best, the air supply system must be properly installed and maintained regularly. A drawing in this section shows a properly installed air supply system. Handy checklists for installing and maintaining air supply systems follow. The air system is lubricated regularly. A regular maintenance program is followed.
AIR SYSTEMS - Continued Calculating Compressor Size Use the air consumption chart in the Tool Schematic for each tool when calculating the operating requirements for the tools. Paslode® tools are designed to operate efficently between 90 and 120 psi and should never be operated at pressure greater than 120 psi. The air consumption chart will help you find the correct compressor size for your application that will quickly replenish tool air pressure.
F325R FEATURES & BENEFITS Nonslip No-Mar Protection Tool-Less Depth of Drive Prevents scratches of interior work surfaces and prevents the tool from sliding on smooth surfaces Provides precise control of nail depth (on other side) Metal Exhaust Cap For maximun durability. Aggressive Work Contact Grabs the wood when toe nailing. Dual Mode Trigger Lock Out Switches from sequential to bounce fire. Eliminates blank firing.
F325R , 513000 PARTS LEGEND 1 2 3 4 5 * 6 * 7 * 8 * 9 10 * 11 * 12 13 14 15 16 17 * 18 * 19 20 * 21 * 22 * 23 24 25 26 27 28 29 30 31 32 33 34 35 * 36 37 38 511943 511444 511847 408302 513003 511413 513042 201756 202398 511960 539676 511876 511719 1011802 511799 511411 511409 511410 511970 511407 511447 511576 511585 511448 502050 404361 502046 502049 502061 502036 502047 513002 502058 502333 502324 502042 511713 502033 1 1 4 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 Nut, Nyl
F325R 513000 Piston Assembly 513008 1 2 55 56 16 3 70 # 120 # 59 58 57 65 # 32 4 4 5 34 35 36 37 33 6 7 Main Valve Assembly 511465 8 9 24 38 40 25 51 52 26 ➔ 11 12 Note: Install check band with thick side down.
MAINTENANCE ❑ Open the drain on the air compressor tank to drain any moisture at least daily in extremely cold or humid weather. A few ounces of anti-freeze in the tank will keep the air free of frost. Paslode® tools are built for ease of maintenance. A few simple details will assure trouble-free operation and long tool life. Anyone who uses or maintains the tool must read the safety and maintenance instructions. Study the schematic drawing before starting any repairs on the tool.
MAINTENANCE - Continued CAUTION Disconnect the tool when performing repairs or clearing jams. MAINTENANCE TABLE ACTION WHY HOW Drain air line filter(daily). Prevent accumulation of mositure and dirt. Open manual petcock (most air supply systems have such a valve). Keep lubricator filled. Keep tool lubricated. Fill with pneumatic tool lubricant. Part No. 403720. Clean filter element-then blow air through filter in direction opposite to normal flow. Prevent clogging of filter with dirt.
OPERATOR TROUBLESHOOTING CAUTION Disconnect the tool when performing repairs or clearing jams. PROBLEM CORRECTIVE ACTION Adjust work contacting element (retract length). Fasteners will not drive completely into wood. Increase air pressure (do not exceed 120 psi). Increase air flow to tool -- use larger air lines (3/8 inch ID minimum). Fasteners penetrate properly during normal operation, but won't drive fully at faster speeds. Reduce air pressure. Fasteners drive too deeply into wood.
TOOL WARRANTY An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 MODEL F325R Framing Nailer TOOL WARRANTY AND LIMITATIONS Paslode® warrants that newly purchased power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below, after the date of delivery to the original user. ONE-YEAR LIMITED WARRANTY A one-year warranty will apply to all parts, except those which are specifically covered by an extended warranty.
ACCESSORIES Lubricants and Loctite Loctite 242 (Blue) .20 oz. Lubricating Oil 16 oz. Lubricating Oil with Antifreeze 8 oz. Chemplex 710 Lubricant 1lb. Part No. Part No. Part No. Part No. 093500 403720 219090 403734 Tool Cleaner Ideal cleaner for all Paslode ® tools in a 12 oz. aerosol can. Safety Glasses Part No. 219348 Clear Part No. 401382 No Mar Work Contact Part No. 502234 For technical support call 1-800-222-6990. To purchase parts and accessories, visit www.itwconstructionparts.com.
ACESORIOS Lubricantes Y Loctite Loctite 242 (Azul ) Acetite Lubricante 16 oz. Acetite Lubricante 8 oz . Lubricante Chemplex 710 1lb. Pieza No. Pieza No. Pieza No. Pieza No. 093500 403720 219090 403734 Limpiador El limpiador ideal para todas las herramientas Lentes de Seguridad Claros Pieza No. 219348 Pieza No. 401382 Kit de reparación de parte de F325R Pieza No. 219389 Contacto de elemento "no-mar" Pieza No. 502234 Para llamada técnica de apoyo, 1-800-222-6990.
GARANTÍA An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 TERMINOS DE LA GARANTÍA Paslode ® garantías que sus herramientas mecánicas, sus piezas y accesorios, que hayan sido comprados nuevos, están libres de defectos de material y fabricación por el período indicado más abajo, a partir de la fecha de compra del comprador original.
DETECCION Y CORRECCION DE FALLAS PRECAUCIÓN Desconecte la herramienta al hacer cualquier reparación o eliminar cualquier obstrucción. PROBLEMA SOLUCIÓN Los sujetadores no penetran completamente en la madera. Cambie la posición del elemento de contacto (Retraiga la longitud). Aumente la presión de aire (no debe exceder 120 psi). Los sujetadores penetran bien durante las operaciones normales, pero fallan a velocidades más altas.
MANTENIMIENTO (continuación) PRECAUCIÓN Desconecte la herramienta al hacer cualquier reparación o eliminar cualquier obstrucción. TABLA DE MANTENIMIENTO ACTIVIDAD POR QUE COMO Drene el filtro de la línea de aire a diario. Para evitar que se acumulen la humedad y la suciedad. Abra la llave de escape. (La mayoría de los sistemas neumáticos la tienen.) Mantenga lleno el lubricador. Para mantener lubricada la herramienta. Llene con lubricante neumático N° 403720 (474 ml).
MANTENIMIENTO El mantenimiento de cualquier herramienta Paslode ® es simple. Su funcionamiento sin problemas y la prolongación de la vida de la herramienta se logran siguiendo un sencillo procedimiento. Las personas encargadas de usar y mantener la herramienta deben leer las instrucciones de seguridad y mantenemiento. Estudie los diagramas antes de hacer cualquier reparación.
F325R 513000 Montaje del Pistón 1 513008 2 55 56 16 3 70 # 59 58 57 120 # 65 # 32 4 4 33 5 34 6 7 Válvula Principal 511465 8 9 24 38 40 25 11 12 51 52 26 ➔ Nota: Manga de instalación verificación banda gruesa hacia abajo.
F325R , 513000 LIS TA DE PIEZAS 1 2 3 4 5 * 6 * 7 * 8 * 9 10 * 11 * 12 13 14 15 16 17 * 18 * 19 20 * 21 * 22 * 23 24 25 26 27 28 29 30 31 32 33 34 35 * 36 37 38 * ** 511943 511444 511847 408302 513003 511413 513042 201756 202398 511960 539676 511876 511719 1011802 511799 511411 511409 511410 511970 511407 511447 511576 511585 511448 502050 404361 502046 502049 502061 502036 502047 513002 502058 502333 502324 502042 511713 502033 1 1 4 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1
F 325 R Características y Beneficios Antideslizante Protección No-Mar Ajuste de Profundidad Sin Uso de Herramienta Evita los arañazos de las superficies de trabajo interiores y evita que la herramienta se deslizamiento sobre superficies lisas Proporciona control preciso de la profundidad de clavo (sobre lado opuesto) Tapa de Escape Hecha de Metal Contacto Agresivo Para máxima durabilidad Agarra la madera cuando sujeta clavos oblicuos Gatillo en modo dual Cambia de disparos en secuencia a disparos en
SISTEMAS NEUMATICOS (continuación) Cómo Calcular la Tubería Necesaria Por ejemplo, si un compresor eléctrico de 20 hp proporciona aproximadamente 80 pies³/min. de aire a 120 psi y la longitud de la línea principal es de 106.70 m, la tabla indica que el diámetro interior de la línea principal necesario para esta aplicación debe ser de 1-1/4 pulgadas como mínimo.
SISTEMAS NEUMÁTICOS ■ Las mangueras de aire no midan más de 45.70 m de longitud. ■ El sistema neumático sea lubricado periódicamente. ■ Se siga un programa regular de mantenimiento. El sistema neumático debe estar correctamente instalado y recibir mantenimiento periódicamente para que todas las herramientas de potencia neumática funcionen bien. El diagrama de más abajo muestra un sistema neumático correctamente instalado.
FUNCIONAMIENTO DE LA HERRAMIENTA (continuación) Funcionamiento en secuencia El juego de funcionamiento en secuencia evita los impulsos sucesivos o "de rebote". Sujetadores ■ Oprima el elemento de contacto y manténgalo apoyado contra el material de trabajo antes de apreter el gatillo. Paso 1 Tome firmamente el mango. Paso 2 Insertar uno o uno tiras de clavos en parte atras del cargador.
INSTALACION DE LA HERRAMIENTA FUNCIONAMIENTO DE LA HERRAMIENTA Regulación de la profundida de colocación (en herramientas que tienen esta car- PELIGRO La presión de aire en la herramienta nunca debe exceder 120 psi. acterística) PELIGRO Apunte la herramienta en alguna dirección en que no haya peligro. Deconéctela de la fuente de aire comprimido y quítele todos los sujetadores. Su herramienta Paslode está lista para usarse y se puede unstalar siguiendo estos pasos: ® 1.
INSTRUCCIONES DE SEGURIDAD LA SEGURIDAD ESTA PRIMERO DESCONECTE LA HERRAMIENTA CUANDO NO LA ESTE USANDO Estas instrucciones proporcionan la información necesatia para el funcionamiento sin peligrode las herramientas Paslode®. No trate de usar su herramienta hasta que no haya léido y entendido todas las precauciones de seguridad y las instrucciones de este manual. Siempre desconecte la herramienta de la línea de aire comprimdo cuando no la esté usando o al dejar su lugar de trabajo.
SPECIFICACIONES DE LA HERRAMIENTA Y LOS SUJETADORES SPECIFICACIONES de la HERRAMIENTA MODELO NO. F325R (5130000) ALTURA 12.9” ANCHO 4.3" LARGO 12.3" PESO 5.9 lbs. PRESION de OPERACION 90 hasta 120 p.s.i. (6.2 hasta 8.3 bar) TIPO DE CARGADOR 30 grados, la Franja de SPECIFICACIONES de los SUJETADORES LONGITUD DEL CLAVO 2”- 3-1/4" DIAMETRO .113 - .131 ACOPLAMIENTO DE AIRE: Esta herramienta utiliza un enchufe de 3/8" N.P.T.
INTRODUCCION La herramienta Paslode® F325R clavadora remodelación es una herramienta de calidad, diseñada para uso en aplicaciones residencial. Esta herramienta le provera confiabilidad y eficencia cuando sea usada acorde con las reglas del fabricante. Lea cudadosamente este manual y las instrucciones de seguridad para comprender como usar le herrminienta correctamente. CONTENIDO SPECIFICACIONES DEL LA HERRAMINETA Y SUS SUJETADORES.............................3 INSTRUCCIONES DE SEGURIDAD.....................
MODELO F325R Framing Clavadora ¡IMPORTANTE! NO DESTRUYE ESTE MANUAL El cliente tiene la responsibilidad de que todo el personal de operaciones y servicio lea y entienda este manual.